Hi,
Sorry for the late reply... so the switching to PAL was because i was
setting it to that in my modules.conf. I was messing wiht all the
settings... trying different tuner types just to see if anythign would
work.
my modules.conf now has just the following
alias char-major-81 videodev
alias char-major-81-0 ivtv
alias tveeprom tveeprom-ivtv
so here is my output from
dmesg | tac |
sed -n '/=\ \ END INIT IVTV\ \ =/,/= START INIT IVTV =/p;
/= START INIT IVTV =/q' |
tac
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.2.0 (rc3g) loading
ivtv: Linux version: 2.6.11-rc4-kraxel2 preempt PENTIUMIII gcc-3.3
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 350 card
ivtv: Found an iTVC15 based chip
PCI: Found IRQ 9 for device 0000:01:07.0
PCI: Sharing IRQ 9 with 0000:00:01.0
ivtv: XXX PCI device: 0x7124 vendor: 0x8086
ivtv: i2c attach [client=tveeprom,ok]
ivtv: i2c attach [client=(tuner unset),ok]
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
saa7115: detecting saa7115 client on address 0x42
saa7115: writing init values
ivtv: i2c attach [client=saa7115[2],ok]
saa7115: status: (1E) 0xa4, (1F) 0xa0
saa7127: Selecting NTSC video Standard
saa7127: Selecting S-Video+Composite
saa7127: Turn WSS off
saa7127: Widescreen Mode 4:3 Full Format
saa7127: Selecting Normal Encoder Input
saa7127: Enable Video Output
ivtv: i2c attach [client=saa7127[2],ok]
msp34xx: ivtv version
msp34xx: init: chip=MSP3448W-A2, has NICAM support, simple (D) mode,
simpler (G) no-thread mode
msp34xx: $Id$ compiled on: Feb 23 2005 22:05:06
ivtv: i2c attach [client=MSP3448W-A2,ok]
tveeprom: Hauppauge: model = 48132, rev = K268, serial# = 7683271
tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio_processor = MSP3440 (type = 11)
ivtv: Tuner Type 47, Tuner formats 0x00001000, Radio: yes, Model
0x00ad2598, Revision 0xd0bde88c
ivtv: NTSC tuner detected
ivtv: Radio detected
ivtv: Encoder revision: 0x02040011
ivtv: Decoder revision: 0x02020023
ivtv: Configuring WinTV PVR 350 card with 9 streams
ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes total
ivtv: Registered v4l2 device, streamtype 0 minor 0
ivtv: Create DMA stream 1
ivtv: Registered v4l2 device, streamtype 1 minor 32
ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 224
ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 3 minor 24
ivtv: Create stream 4
ivtv: Registered v4l2 device, streamtype 4 minor 64
ivtv: Create DMA stream 5 using 16 65536 byte buffers 1048576 kbytes total
ivtv: Registered v4l2 device, streamtype 5 minor 16
ivtv: Create stream 6 using 1024 2048 byte buffers 262144 kbytes total
ivtv: Registered v4l2 device, streamtype 6 minor 228
ivtv: Create stream 7
ivtv: Registered v4l2 device, streamtype 7 minor 232
ivtv: Create DMA stream 8
ivtv: Registered v4l2 device, streamtype 8 minor 48
ivtv: Setting Tuner 47
tuner 1-0061: type set to 47 (LG NTSC (TAPE series))
ivtv: Setting audio matrix to input 3, output 1
ivtv: Switching standard to NTSC.
ivtv: ivtv_enc_thread: pid = 7264, itv = 0xd0bd3780
ivtv: ivtv_dec_thread: pid = 7265, itv = 0xd0bd3780
saa7115: decoder set norm NTSC
saa7115: set audio: 0x01
saa7127: Setting Encoder Video Standard
saa7127: Set NTSC Video Mode
saa7127: Selecting NTSC video Standard
ivtv: Initialized WinTV PVR 350, card #0
ivtv: ==================== END INIT IVTV ====================
ive been using ptune-ui to change frequencies and using mplayer -vo
xv /dev/video0 to view.
All channels still come in static except channel 14 when using
ntsc-cable-jp. channel 14 comes in black and white with some static,
but you can see the silhouettes of the images. Also I dual boot
windows xp and have tested the card under xp and it works fine when
using the hauppauge software with ntsc hrc cable.
also here is the output from lsmod
Module Size Used by
ivtv 818244 1
msp3400 29464 0
saa7127 13628 0
saa7115 13560 0
tuner 28104 0
tveeprom 13144 0
i2c_algo_bit 9864 1 ivtv
videodev 10240 2 ivtv
ipv6 269376 8
af_packet 22888 2
snd_intel8x0 32672 0
snd_ac97_codec 76544 1 snd_intel8x0
snd_pcm 94440 2 snd_intel8x0,snd_ac97_codec
snd_timer 26532 1 snd_pcm
snd 54724 4 snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
snd_page_alloc 10020 2 snd_intel8x0,snd_pcm
i2c_i801 8620 0
i2c_core 23120 7
msp3400,saa7127,saa7115,tuner,tveeprom,i2c_algo_bit,i2c_i801
shpchp 82388 0
pci_hotplug 35184 1 shpchp
hw_random 5620 0
intel_agp 23100 1
rtc 13304 1
pcspkr 3716 0
tsdev 7776 0
mousedev 12056 2
psmouse 29672 0
floppy 61328 0
evdev 9568 0
uhci_hcd 32688 0
usbcore 121592 2 uhci_hcd
i810_audio 36180 1
ac97_codec 19916 1 i810_audio
soundcore 10528 3 snd,i810_audio
3c59x 42152 0
mii 4992 1 3c59x
agpgart 35176 2 intel_agp
ide_cd 42308 0
cdrom 41632 1 ide_cd
ext3 145128 1
jbd 63160 1 ext3
mbcache 10692 1 ext3
ide_generic 1120 0 [permanent]
via82cxxx 12284 0 [permanent]
trm290 4228 0 [permanent]
triflex 3648 0 [permanent]
slc90e66 5824 0 [permanent]
sis5513 14536 0 [permanent]
siimage 12544 0 [permanent]
serverworks 7624 0 [permanent]
sc1200 7168 0 [permanent]
rz1000 2496 0 [permanent]
piix 10660 0 [permanent]
pdc202xx_old 11296 0 [permanent]
opti621 4676 0 [permanent]
ns87415 3688 0 [permanent]
hpt366 20192 0 [permanent]
ide_disk 18496 4 hpt366
hpt34x 5216 0 [permanent]
generic 3904 0 [permanent]
cy82c693 4480 0 [permanent]
cs5530 4864 0 [permanent]
cs5520 4640 0 [permanent]
cmd64x 12028 0 [permanent]
atiixp 6288 0 [permanent]
amd74xx 13116 0 [permanent]
alim15x3 10636 0 [permanent]
aec62xx 7520 0 [permanent]
pdc202xx_new 9024 0 [permanent]
ide_core 129164 28
ide_cd,ide_generic,via82cxxx,trm290,triflex,slc90e66,sis5513,siimage,serverworks,sc1200,rz1000,piix,pdc202xx_old,opti621,ns87415,hpt366,ide_disk,hpt34x,generic,cy82c693,cs5530,cs5520,cmd64x,atiixp,amd74xx,alim15x3,aec62xx,pdc202xx_new
unix 29460 474
one last thing, here is the output from
find /lib/modules/2.6.11-rc4-kraxel2/ -name "tuner*"
/lib/modules/2.6.11-rc4-kraxel2/kernel/drivers/media/video/tuner-3036.ko.bak
/lib/modules/2.6.11-rc4-kraxel2/kernel/drivers/media/video/tuner.ko
/lib/modules/2.6.11-rc4-kraxel2/v4l2/tuner.ko.bak
find /lib/modules/2.6.11-rc4-kraxel2/ -name "tveeprom*"
/lib/modules/2.6.11-rc4-kraxel2/kernel/drivers/media/video/tveeprom.ko
/lib/modules/2.6.11-rc4-kraxel2/extra/tveeprom.ko.bak
/lib/modules/2.6.11-rc4-kraxel2/v4l2/tveeprom.ko.bak
find /lib/modules/2.6.11-rc4-kraxel2/ -name "msp3400*"
/lib/modules/2.6.11-rc4-kraxel2/extra/msp3400.ko
/lib/modules/2.6.11-rc4-kraxel2/v4l2/msp3400.ko.bak
thanks,
Jeff
On Mon, 7 Mar 2005 00:10:40 -0800, Jarod Wilson <[EMAIL PROTECTED]> wrote:
> On Sunday 06 March 2005 19:13, Jeffrey Zellman wrote:
> > ivtv: Setting Tuner 47
> > tuner 0-0061: type set to 47 (LG NTSC (TAPE series))
>
> NTSC tuner...
>
> > ivtv: Setting audio matrix to input 3, output 1
> > ivtv: Switching standard to PAL.
> > ivtv: ivtv_enc_thread: pid = 2539, itv = 0xd09ab780
> > ivtv: ivtv_dec_thread: pid = 2540, itv = 0xd09ab780
> > spurious 8259A interrupt: IRQ7.
> > saa7115: decoder set norm PAL
> > saa7115: set audio: 0x01
> > saa7127: Setting Encoder Video Standard
> > saa7127: Set PAL Video Mode
> > saa7127: Selecting PAL video Standard
> > ivtv: Initialized WinTV PVR 350, card #0
>
> Then you're doing something that changes the card to PAL mode (bad
> modprobe.conf options?). Thus the static.
>
> --
> Jarod Wilson
> [EMAIL PROTECTED]
>
>
>
-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now.
http://ads.osdn.com/?ad_id=6595&alloc_id=14396&op=click
_______________________________________________
ivtv-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/ivtv-devel
