I've got some bad news for you Jerry, I didn't have a problem at all
under Ubuntu AMD64. I have a fresh install of Ubuntu 5.02. I followed
my own guide from the Wiki:
http://ivtv.writeme.ch/tiki-index.php?page=KubuntuHowTo
I didn't add any module options, but I did remove all the conflicting
modules listed during `make install`. After the modprobe, I just cat
/dev/video0 > test.mpg, let it run for a minute, then played the file.
I'm using the newest firmware from Haupauge's site. Here's my dmesg,
and I can give you more info if you want to get in touch with me off-list.
Jerry Burgess wrote:
Oh that's right, you were the one with the
firmware load problem. I
run ubuntu with the 686 version of that same kernel,
with the exact same
PVR-150 card.
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.3.6 (i) loading
ivtv: Linux version: 2.6.10-5-amd64-k8 gcc-3.3
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 150 card
ivtv: Found an iTVC16 based chip
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 17 (level, low) -> IRQ 17
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: XXX PCI device: 0x00e1 vendor: 0x10de
tveeprom: Hauppauge: model = 26032, rev = C199, serial# = 7937296
tveeprom: tuner = TCL 2002N 5H (idx = 99, type = 50)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio_processor = TDA9850 (type = 3)
ivtv: i2c attach [client=tveeprom[50],ok]
ivtv: Tuner Type 50, Tuner formats 0x00001000, Radio: yes, Model 0x008d1659,
Revision 0x00000000
ivtv: NTSC tuner detected
ivtv: Radio detected
tuner: Ignoring new-style parameters in presence of obsolete ones
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach [client=(tuner unset),ok]
cx25840: starting probe for adapter ivtv i2c driver #0 (0x10005)
cx25840: detecting cx25840 client on address 0x88
cx25840: writing init values
cx25840: requesting /lib/modules/HcwMakoA.ROM
cx25840: firmware loaded
cx25840: Status: cx258413 (DEVICE_ID)
ivtv: i2c attach [client=cx25840[50],ok]
ivtv: i2c attach [client=wm8775[50],ok]
ivtv: Encoder revision: 0x02050032
ivtv: Encoder Firmware may be buggy, use version 0x02040011
ivtv: Configuring WinTV PVR 150 card with 5 streams
ivtv: Registered v4l2 device, streamtype 0 minor 0
ivtv: Create DMA stream 0 using 128 16384 byte buffers 0 kbytes total
ivtv: Registered v4l2 device, streamtype 1 minor 32
ivtv: Create DMA stream 1 using 194 10800 byte buffers 0 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 224
ivtv: Create DMA stream 2 using 240 8736 byte buffers 0 kbytes total
ivtv: Registered v4l2 device, streamtype 3 minor 24
ivtv: Create DMA stream 3 using 455 4608 byte buffers 0 kbytes total
ivtv: Registered v4l2 device, streamtype 4 minor 64
ivtv: Create stream 4
ivtv: Setting Tuner 50
tuner: type set to 50 (TCL 2002N) by ivtv i2c driver #0
cx25840: decoder set norm NTSC
ivtv: ivtv_enc_thread: pid = 9202, itv = 0xffffffffa03a6480
ivtv: ivtv_enc_vbi_thread: pid = 9203, itv = 0xffffffffa03a6480
cx25840: decoder set input (6)
cx25840: now setting Tuner input
cx25840: set audio input (0)
ivtv: Switching standard to NTSC.
ivtv: Initialized WinTV PVR 150, card #0
ivtv: ==================== END INIT IVTV ====================
