On Sunday 19 June 2005 01:09 pm, William Powers wrote: > Have you tried swapping the second card with the first card to see if > you can get it to work in a single card config?
Just did, and this is not a two card config problem... I have just booted with ONLY the card I can't get working, and it does not seem to be working by itself. Here is the IVTV initialization: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.3 (t) loading ivtv: Linux version: 2.6.10-gentoo-r6-badram preempt PENTIUM4 4KSTACKS gcc-3.3 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 250 card ivtv: Found an iTVC15 based chip ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 11 (level, low) -> IRQ 11 ivtv: Unreasonably low latency timer, setting to 64 (was 32) ivtv: VIA PCI device: 0x3168 vendor: 0x1106 tveeprom: Hauppauge: model = 48432, rev = I110, serial# = 6143256 tveeprom: tuner = Philips FI1236 MK2 (idx = 10, type = 2) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio_processor = MSP3440 (type = 11) ivtv: i2c attach [client=tveeprom[50],ok] ivtv: Tuner Type 2, Tuner formats 0x00001000, Radio: yes, Model 0x00a51450, Revision 0x00000000 ivtv: NTSC tuner detected ivtv: Radio detected tuner: Ignoring new-style parameters in presence of obsolete ones tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach [client=(tuner unset),ok] saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005) saa7115: detecting saa7115 client on address 0x42 saa7115: writing init values ivtv: i2c attach [client=saa7115[50],ok] saa7115: status: (1E) 0x48, (1F) 0xc0 msp34xx: ivtv version msp34xx: init: chip=MSP3448W-A2, has NICAM support, simple (D) mode, simpler (G) no-thread mode msp34xx: $Id$ compiled on: May 22 2005 22:53:54 ivtv: i2c attach [client=MSP3448W-A2,ok] ivtv: Encoder revision: 0x02040024 ivtv: Encoder Firmware may be buggy, use version 0x02040011 ivtv: Decoder revision: 0x02020023 ivtv: Configuring WinTV PVR 250 card with 5 streams ivtv: Registered v4l2 device, streamtype 0 minor 0 ivtv: Create DMA stream 0 using 1024 16384 byte buffers 0 kbytes total ivtv: Allocate DMA stream 0 using 1024 16384 byte buffers 16777216 kbytes total ivtv: Registered v4l2 device, streamtype 1 minor 32 ivtv: Create DMA stream 1 ivtv: Allocate DMA stream 1 ivtv: Registered v4l2 device, streamtype 2 minor 224 ivtv: Create DMA stream 2 using 80 52224 byte buffers 0 kbytes total ivtv: Allocate DMA stream 2 using 80 52224 byte buffers 4194304 kbytes total ivtv: Registered v4l2 device, streamtype 3 minor 24 ivtv: Create DMA stream 3 using 455 4608 byte buffers 0 kbytes total ivtv: Allocate DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 4 minor 64 ivtv: Create stream 4 ivtv: Allocate stream 4 ivtv: Setting Tuner 2 tuner: type set to 2 (Philips NTSC (FI1236,FM1236 and compatibles)) by ivtv i2c driver #0 saa7115: decoder set input (4) saa7115: now setting Composite input ivtv: Setting audio matrix to input 3, output 1 ivtv: Switching standard to NTSC. ivtv: ivtv_enc_thread: pid = 5293, itv = 0xe0ae83a0 spurious 8259A interrupt: IRQ7. saa7115: decoder set norm NTSC saa7115: set audio: 0x01 ivtv: Initialized WinTV PVR 250, card #0 ivtv: ==================== END INIT IVTV ==================== Seems fine, but then I get this kind of junk: msp34xx: I/O error #1 (write 0x12/0x00) msp34xx: I/O error #2 (write 0x12/0x00) msp34xx: I/O error #3 (write 0x12/0x00) msp34xx: giving up, reseting chip. Sound will go off, sorry folks :-| msp3400: chip reset failed msp34xx: I/O error #1 (write 0x12/0x06) msp34xx: I/O error #3 (write 0x12/0x06) ivtv: Failed api call 0x000000b7 with result 0xfffffff0 ivtv: Failed api call 0x000000b7 with result 0xfffffff0 ivtv: Failed api call 0x000000b7 with result 0xfffffff0 ivtv: Failed api call 0x000000b7 with result 0xfffffff0 saa7115: decoder disable output saa7115: decoder enable output ivtv: Failed api call 0x00000081 with result 0xfffffff0 ivtv: Error starting capture!!! ivtv: Failed to start capturing for stream 0 If anybody knows what options I need to pass this tuner, I'll try them and let you know how it works out! Mat -- mythtv [at] matmrosko [dot] com ------------------------------------------------------- SF.Net email is sponsored by: Discover Easy Linux Migration Strategies from IBM. Find simple to follow Roadmaps, straightforward articles, informative Webcasts and more! Get everything you need to get up to speed, fast. http://ads.osdn.com/?ad_id=7477&alloc_id=16492&op=click _______________________________________________ ivtv-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/ivtv-devel
