Hello,
I am trying to install a Hauppauge PVR500 card and am running into some issues.
No matter what I try, the driver always complains it can't talk to the
tveeprom.ko module. I installed ivtv from the ATrpms for RHEL4 using the
following steps.
yum install ivtv-firmware-audio
yum install ivtv-firmware
yum install ivtv-kmdl-`uname -r`
Here is my setup.
Hardware:
HP LP1000R Netserver dual processor Intel P3 833 with 512MB ram
CentOS 4.3 (RHEL4)
Kernel 2.6.9-34.ELsmp
/etc/modprobe.conf
alias scsi_hostadapter sata_promise
alias eth0 e100
alias eth1 e100
alias scsi_hostadapter1 sym53c8xx
alias usb-controller ohci-hcd
# ivtv setup
alias char-major-81 videodev
alias char-major-81-0 ivtv
alias char-major-81-1 ivtv
options ivtv ivtv_debug=1
lspci output:
01:08.0 Multimedia video controller: Internext Compression Inc iTVC16 (CX23416)
MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc. WinTV PVR 500 (1st unit)
Flags: bus master, medium devsel, latency 64, IRQ 7
Memory at f4000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
01:09.0 Multimedia video controller: Internext Compression Inc iTVC16 (CX23416)
MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc. WinTV PVR 500 (2nd unit)
Flags: bus master, medium devsel, latency 64, IRQ 7
Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
dmesg
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.4.5 (tagged release) loading
ivtv: Linux version: 2.6.9-34.ELsmp SMP 686 REGPARM 4KSTACKS gcc-3.4
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected WinTV PVR 150 card (cx23416 based)
ACPI: PCI interrupt 0000:01:08.0[A]: no GSI - using IRQ 7
ivtv0 warning: i2c client addr: 0x50 not found for command 0x0!
ivtv0: Error -19 reading Hauppauge eeprom.
ivtv0: Possible causes: the tveeprom module was not loaded, or
ivtv0: the eeprom kernel module was loaded before the tveeprom module.
ivtv0 warning: i2c client addr: 0x44 not found for command 0xc008561c!
ivtv0: Could not detect tuner standard, defaulting to NTSC.
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0 warning: Encoder mailbox not found
ivtv0 warning: Decoder mailbox not found
ivtv0: Error locating firmware.
ivtv0: Error -12 on initialization
ivtv: probe of 0000:01:08.0 failed with error -12
ivtv0: Autodetected WinTV PVR 150 card (cx23416 based)
ACPI: PCI interrupt 0000:01:09.0[A]: no GSI - using IRQ 7
ivtv0 warning: i2c client addr: 0x50 not found for command 0x0!
ivtv0: Error -19 reading Hauppauge eeprom.
ivtv0: Possible causes: the tveeprom module was not loaded, or
ivtv0: the eeprom kernel module was loaded before the tveeprom module.
ivtv0 warning: i2c client addr: 0x44 not found for command 0xc008561c!
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0 warning: Encoder mailbox not found
ivtv0 warning: Decoder mailbox not found
ivtv0: Error locating firmware.
ivtv0: Error -12 on initialization
ivtv: probe of 0000:01:09.0 failed with error -12
ivtv: ==================== END INIT IVTV ====================
Any help would be greatly appreciated!
Thank you,
Stew
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
