Hi. I've installed a new PVR-150 card but can't get any audio out of it. The video works fine with 'v4l2-ctl -i 0' (etc) then 'mplayer /dev/video0', 'VDR' or 'cat /dev/video0'. But nothing produces any audio!
If I play this under windows, there are 2 audio tracks, but no sound. IVTV-radio also produces no sound: ivtv-radio -f 90.9 Any ideas? ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.8.2 (tagged release) loading ivtv: Linux version: 2.6.18-1.2257.fc5 mod_unload 686 REGPARM 4KSTACKS gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 185 PCI: VIA IRQ fixup for 0000:00:10.2, from 11 to 9 uhci_hcd 0000:00:10.2: UHCI Host Controller uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:10.2: irq 185, io base 0x0000dc00 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ieee1394: Initialized config rom entry `ip1394' ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 185 PCI: VIA IRQ fixup for 0000:00:10.3, from 11 to 9 uhci_hcd 0000:00:10.3: UHCI Host Controller uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:10.3: irq 185, io base 0x0000e000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ivtv0: Autodetected Hauppauge card (cx23416 based) ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 193 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 1:0:0:0: Attached scsi generic sg1 type 0 ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) tveeprom 0-0050: Hauppauge model 26559, rev F089, serial# 10187014 tveeprom 0-0050: tuner model is TCL MFPE05 2 (idx 89, type 38) tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74) tveeprom 0-0050: audio processor is CX25843 (idx 37) tveeprom 0-0050: decoder processor is CX25843 (idx 30) tveeprom 0-0050: has radio, has no IR remote ivtv0: Autodetected Hauppauge WinTV PVR-150 tuner 0-0043: chip found @ 0x86 (ivtv i2c driver #0) tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner) tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0) cx25840 0-0044: loaded v4l-cx25840.fw firmware (16382 bytes) wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0) ivtv0: Encoder revision: 0x02050032 ivtv0: Registered device video0 for encoder MPEG ivtv0: Registered device video32 for encoder YUV ivtv0: Registered device vbi0 for encoder VBI ivtv0: Registered device video24 for encoder PCM audio ivtv0: Registered device radio0 for encoder radio tuner 0-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== _______________________________________________ ivtv-users mailing list ivtv-users@ivtvdriver.org http://ivtvdriver.org/mailman/listinfo/ivtv-users
