RE: [Ivtv-users] (no subject)

Fri, 07 Jan 2005 04:21:32 -0800

Hi, I just discovered that this (no firmware loading) happens only when module is loaded at boot time, when doing an rmmod ivtv and then reinserting the module there are no error messages in the log.
 
What can be causing this to fail at boot time? I am not entirely sure when the module is loaded, but I have followed the instructions on the fedora myth(tv)ology website, including generating a new initrd as described using "mkinitrd -f --with=tveeprom --with=saa7115 --with=tuner --with=saa7127 --with=ivtv --with=ivtv-fb /boot/initrd-`uname -r`.img `uname -r` ".
 
Geir 

From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Geir Ertzaas
Sent: Friday, January 07, 2005 12:39 PM
To: [email protected]
Subject: [Ivtv-users] (no subject)

I am attempting to install ivtv-0.2.0-58_rc3c under FC3 using rpms but I need some help on getting the ivtv module to load correctly.

A. I get the message "localhost kernel: tveeprom: no version for "struct_module" found: kernel tainted." in my messages log - should I worry about this message?

B. I am getting a message saying that ivtv was unable to open the firmware file /lib/modules/ivtv-fw-enc.bin. This file exists and is readable by everyone. What can be wrong?

Log included below.

Regards,

Geir


Jan  7 11:26:02 localhost kernel: ivtv: ==================== START INIT IVTV ====================
Jan  7 11:26:02 localhost kernel: ivtv: version 0.2.0 (rc3b) loading
Jan  7 11:26:02 localhost kernel: ivtv: Linux version: 2.6.9-1.724_FC3 686 REGPARM 4KSTACKS gcc-3.4
Jan  7 11:26:02 localhost kernel: ivtv: In case of problems please include the debug info
Jan  7 11:26:02 localhost kernel: ivtv: between the START INIT IVTV and END INIT IVTV lines when
Jan  7 11:26:02 localhost kernel: ivtv: mailing the ivtv-devel mailinglist.
Jan  7 11:26:02 localhost kernel: ivtv: Autodetected WinTV PVR 350 card
Jan  7 11:26:02 localhost kernel: ivtv: Found an iTVC15 based chip
Jan  7 11:26:02 localhost kernel: ACPI: PCI interrupt 0000:01:0b.0[A] -> GSI 5 (level, low) -> IRQ 5
Jan  7 11:26:02 localhost kernel: ivtv: XXX PCI device: 0x2570 vendor: 0x8086
Jan  7 11:26:02 localhost kernel: tveeprom: Hauppauge: model = 48134, rev = J347, serial# = 6594583
Jan  7 11:26:02 localhost kernel: tveeprom: tuner = LG TP18PSB01D (idx = 47, type = 28)
Jan  7 11:26:02 localhost kernel: tveeprom: tuner fmt = PAL(B/G) (eeprom = 0x04, v4l2 = 0x00000007)
Jan  7 11:26:02 localhost kernel: tveeprom: audio_processor = CS5331 (type = 9)
Jan  7 11:26:02 localhost rpcidmapd: rpc.idmapd oppstart succeeded
Jan  7 11:26:02 localhost kernel: ivtv: i2c attach [client=tveeprom[0],ok]
Jan  7 11:26:02 localhost kernel: saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
Jan  7 11:26:02 localhost kernel: saa7115: detecting saa7115 client on address 0x42
Jan  7 11:26:02 localhost kernel: saa7115: writing init values
Jan  7 11:26:02 localhost kernel: ivtv: i2c attach [client=saa7115[0],ok]
Jan  7 11:26:02 localhost kernel: saa7115: status: (1E) 0x48, (1F) 0xc0
Jan  7 11:26:02 localhost kernel: tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
Jan  7 11:26:02 localhost kernel: ivtv: i2c attach [client=(tuner unset),ok]
Jan  7 11:26:02 localhost netfs: Monterer andre filsystemer:  succeeded
Jan  7 11:26:02 localhost kernel: saa7127: Selecting NTSC video Standard
Jan  7 11:26:02 localhost kernel: saa7127: Selecting S-Video+Composite
Jan  7 11:26:02 localhost kernel: saa7127: Turn WSS off
Jan  7 11:26:02 localhost kernel: saa7127: Widescreen Mode 4:3 Full Format
Jan  7 11:26:02 localhost kernel: saa7127: Selecting Normal Encoder Input
Jan  7 11:26:02 localhost kernel: saa7127: Enable Video Output
Jan  7 11:26:02 localhost kernel: ivtv: i2c attach [client=saa7127[0],ok]
Jan  7 11:26:02 localhost kernel: ivtv: Tuner Type 28, Tuner formats 0x00000007, Radio: yes, Model 0x00a93517, Revision 0x00000001

Jan  7 11:26:02 localhost kernel: ivtv: PAL tuner detected
Jan  7 11:26:02 localhost kernel: ivtv: Radio detected
Jan  7 11:26:02 localhost kernel: Unable to open '/lib/modules/ivtv-fw-enc.bin'.
Jan  7 11:26:02 localhost kernel: ivtv: failed loading encoder firmware
Jan  7 11:26:02 localhost kernel: ivtv: Error loading firmware -3!
Jan  7 11:26:02 localhost kernel: ivtv: Error -3 initializing firmware.
Jan  7 11:26:02 localhost kernel: ivtv: Error -12 on initialization
Jan  7 11:26:02 localhost kernel: ivtv-iTVC15_16_mpg2_encoder_card: probe of 0000:01:0b.0 failed with error -12
Jan  7 11:26:02 localhost kernel: ivtv: ====================  END INIT IVTV  ==================


Reply via email to