Oops! I found it in Bert's package... signed with your name! :). Why is not included in Jallib?
On Aug 13, 12:43 pm, vasile surducan <[email protected]> wrote: > On Fri, Aug 13, 2010 at 2:40 AM, funlw65 <[email protected]> wrote: > > BTW, I'm trying to "translate" the "One wire" library from Swordfish > > Basic to Jal (because we don't have one in Jallib)... > > there are at least three different 1w libraries in jal... > > > if I can't, I > > have also C AVR libraries.... > > > On Aug 13, 12:36 pm, funlw65 <[email protected]> wrote: > > > 'till then, nice assembly and interesting project. I suppose every > > > board can be tested before. > > > > Vasi(funlw65) > > > > On Aug 13, 7:50 am, vasile surducan <[email protected]> wrote: > > > > > Till then, my last hobby board, it's a differential thermo relay with > > two > > > > circuits (three temperature sensors on 1W bus, driving two > > electrovalves and > > > > one pump) for two solar heating panel systems situated on two different > > > > directions (south-east and south-west). Some day I'll write about how > > to > > > > build a professional heating panel using only what you can find in a > > shop. I > > > > have 125l of water at 54C in my attic from our God (read sun) during > > one day > > > > of good insolation. > > > > > This is an example of a bad design, caused by the leak of space and > > using > > > > through hole components instead of smds. Because we have spoken here > > about > > > > the jaluino stacked board, this is a staked board, difficult to build > > and > > > > test if need 100 pieces of that... Imagine a beginner testing his > > blinking > > > > LED (and other 10 different things in the same time) on a jalluino > > > > stack...:) > > > > > Vasile > > > > > On Thu, Aug 12, 2010 at 9:08 PM, vasile surducan <[email protected] > > >wrote: > > > > > > Joep, show us the bottom (solder side) too... > > > > > :) > > > > > I had the same boards...I should do a trip in my basement. > > > > > > Vasile > > > > > > On Thu, Aug 12, 2010 at 2:43 PM, funlw65 <[email protected]> wrote: > > > > > >> Thank you Joep, nice lab boards! > > > > > >> Vasi(funlw65) > > > > > >> On Aug 12, 9:24 pm, Joep Suijs <[email protected]> wrote: > > > > >> > Hi Vasi, > > > > > >> > > P.S. I have a proposal. All jallib and JAL developers present a > > photo > > > > >> > > with the board(s) used for development. > > > > > >> > Enclosed a photo of boards I hav mostly used for jallib > > development. > > > > >> > Top left is a dwarf board with zif socket, an extension board with > > > > >> > 7805, i2c connector and my own standard icsp/serial connector > > (onbe > > > > >> > day I'll but this board below the dwarf board). The slave board is > > > > >> > used for the startersguide (led, button. i2c eeprom + connector) > > > > > >> > Top right is an old board, fitted with a zif socket in case I need > > to > > > > >> > work on a 28-pin chip. > > > > > >> > Bottom left is a 18-pin board for work on 16f88 and 16f648. Note > > the > > > > >> > icsp/serial connector on the left and two jumpers required to > > support > > > > >> > these different chips. The 10-pin connector allows to connect > > dwarf > > > > >> > boards. > > > > > >> > Bottom right is the jaluino board with custom shield. This is > > probably > > > > >> > the only board I have without my icsp/serial connector. It is > > fitted > > > > >> > with a pic + bootloader and does have a serial-to-usb board (lower > > > > >> > left on the shield), my standard i2c pinout connector (left, below > > the > > > > >> > display), three leds, two buttons and of course the lcd. > > > > > >> > As you may have noticed, I use audio connector for power supply > > (7-12V > > > > >> > DC) and each board has its own regulator. My boards generally do > > not > > > > >> > contain a reset button, since this is on my programmer connector. > > > > > >> > Cheers, > > > > >> > Joep > > > > > >> > jalboards.jpg > > > > >> > 497KViewDownload > > > > > >> -- > > > > >> You received this message because you are subscribed to the Google > > Groups > > > > >> "jallib" group. > > > > >> To post to this group, send email to [email protected]. > > > > >> To unsubscribe from this group, send email to > > > > >> [email protected]<jallib%[email protected]> > > <jallib%[email protected]<jallib%[email protected]> > > > > > >> . > > > > >> For more options, visit this group at > > > > >>http://groups.google.com/group/jallib?hl=en. > > > > > diff thermorelay small.jpg > > > > 93KViewDownload > > > > > edge view.jpg > > > > 81KViewDownload > > > -- > > You received this message because you are subscribed to the Google Groups > > "jallib" group. > > To post to this group, send email to [email protected]. > > To unsubscribe from this group, send email to > > [email protected]<jallib%[email protected]> > > . > > For more options, visit this group at > >http://groups.google.com/group/jallib?hl=en. -- You received this message because you are subscribed to the Google Groups "jallib" group. To post to this group, send email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/jallib?hl=en.
