Hey guys, I was thinking about creating a timer library for general
setup of a timer. It would be nice to have a library that will allow
users to choose a timer for use with other libraries. I need some
advise/assistance.

My servo libraries allow the user to choose a timer via a constant for
example:
const SERVO_SLAVE_USE_TIMER = 1 -- choose a timer

Here's how it is setup in my libraries. After doing the alias, I can
use the new aliases in the rest of the lib for whatever timer the user
selected. It may be better to place these aliases in their own new
timer lib.

-- setup servo 1 to 8 timer aliases for the timer the user selected
if SERVO_SLAVE_USE_TIMER == 0 then
   -- set special timer0 settings
   t0con_psa  = 0  -- assign prescaler to timer0
   -- set timer registers to timer0
   alias servo_slave_tmr      is TMR0            -- timer interval
   alias servo_slave_cs       is T0CON_T0CS      -- timer clock source
bit
   alias servo_slave_ie       is INTCON_TMR0IE   -- interrupt enable
   alias servo_slave_if       is INTCON_TMR0IF   -- interrupt overflow
bit
   alias servo_slave_ps       is T0CON_T0PS      -- timer prescaler
select bits
   alias servo_slave_on       is T0CON_TMR0ON    -- timer on

   if defined(TMR0H) then
      const SERVO_SLAVE_TIMER_SIZE = 16
   else
      const SERVO_SLAVE_TIMER_SIZE = 8
   end if

elsif SERVO_SLAVE_USE_TIMER == 1 then
   -- set special timer1 settings
   ;t1con_tmr1on = 1               -- enables timer 1
   -- set timer registers to timer1
   alias servo_slave_tmr      is TMR1             -- timer interval
   alias servo_slave_cs       is T1CON_TMR1CS     -- timer clock
source bit
   alias servo_slave_ie       is PIE1_TMR1IE      -- interrupt enable
   alias servo_slave_if       is PIR1_TMR1IF      -- interrupt
overflow bit
   alias servo_slave_ps       is T1CON_T1CKPS     -- timer prescaler
select bits
   alias servo_slave_on       is T1CON_TMR1ON     -- timer on

   if defined(TMR1H) then
      const SERVO_SLAVE_TIMER_SIZE = 16
   else
      const SERVO_SLAVE_TIMER_SIZE = 8
   end if
elsif SERVO_SLAVE_USE_TIMER == 3 then
   ;t3con_tmr3on = 1               -- enables timer 3
   -- set timer registers to timer3
   alias servo_slave_tmr      is TMR3             -- timer interval
   alias servo_slave_cs       is T3CON_TMR3CS     -- timer clock
source bit
   alias servo_slave_ie       is PIE2_TMR3IE      -- interrupt enable
   alias servo_slave_if       is PIR2_TMR3IF      -- interrupt
overflow bit
   alias servo_slave_ps       is T3CON_T3CKPS     -- timer prescaler
select bits
   alias servo_slave_on       is T3CON_TMR3ON    -- timer on

   if defined(TMR3H) then
      const SERVO_SLAVE_TIMER_SIZE = 16
   else
      const SERVO_SLAVE_TIMER_SIZE = 8
   end if
end if



Timers are quite alike for all PIC's. There are a few differences
however:
1. Timer 0 can be either 8 bit or 16 bit. I am able to detect the
size, as seen above.
2. Timer 0 requires setting of t0con_psa  = 0. I suppose I can check
if a tXcon_psa is defined for the selected timer, and set it to 0 if
required. Not sure if this setting will be the same on all PIC's.
3. Prescaler means different things on different PIC's and timers.

So, mainly I have an issue with #3. Is there any way to detect what
prescaler settings are available? Can constants or a constant array be
added to the device files (to hold prescaler speeds that are
available), or is it better to place it in a timer lib for each PIC?

Is there even any efficient way to read these from any file microchip
provides?

18f4620 - Timer0 prescalers:

111 = 1:256
110 = 1:128
101 = 1:64
100 = 1:32
011 = 1:16
010 = 1:8
001 = 1:4
000 = 1:2

18f4620 - Timer1 prescalers:
11 = 1:8
10 = 1:4
01 = 1:2
00 = 1:1

18f4620 - Timer2 prescalers:
0 0= Prescaler is 1
01 = Prescaler is 4
1x = Prescaler is 16

18f4620 - Timer3 prescalers:
11 = 1:8
10 = 1:4
01 = 1:2
00 = 1:1

I haven't used timer2 much, not sure how it works (haven't had time to
check). For now, I only use timers 0, 1 & 3. I currently assume the
prescaler settings are the same as above for all PICs. Is it simply
safe enouf to assume this?

Matt.

-- 
You received this message because you are subscribed to the Google Groups 
"jallib" group.
To post to this group, send email to [email protected].
To unsubscribe from this group, send email to 
[email protected].
For more options, visit this group at 
http://groups.google.com/group/jallib?hl=en.

Reply via email to