I was following a tutorial that I had downloaded and it said: Windows Install: 1. Download jalpack (installer executable) from http://jaledit.googlecode.com/files/JALPack_2.4_0.4_0.6.1.0.exe, This will install JALv2 + JalEdit 2. Update your installation (very important) - Download jallib-pack or jallib-pack-bee from http://code.google.com/ p/jallib/downloads/list, copy the .zip contents into your Jallib installation directory
I guess the tutorial was old as well. Anyway I finally found the 4.60 and 4.62 version though neither of those has an installer for windows so I guess it means just extract it anywhere and run it from that directory. Thanks for the info as I did not realize i was using an older version. Do you know if there is an updated tutorial anywhere? On Apr 6, 6:13 am, Sunish Issac <[email protected]> wrote: > Looks like you mixed a new version of jallib and used the old compiler ? > From where did you download the jalpack ? > > Sunish > > > > > > > > On Fri, Apr 6, 2012 at 2:46 PM, <[email protected]> wrote: > > I am really new to the JAL compiler. I thought I would try a simple blink > > led from the samples. So, I created a new folder in the project folder and > > copied the 16F88 blink file to that folder. Then I compiled it and I got > > like 31 errors. Anyone have any idea what I am doing wrong. > > > code: > > include 16f88 -- target PICmicro > > -- > > -- This program assumes that a 20 MHz resonator or crystal > > -- is connected to pins OSC1 and OSC2. > > -- (unspecified configuration bits may cause a different frequency!) > > pragma target clock 20_000_000 -- oscillator frequency > > -- configuration memory settings (fuses) > > pragma target OSC HS -- HS crystal or resonator > > pragma target WDT disabled -- no watchdog > > pragma target DEBUG disabled -- no debugging > > pragma target LVP disabled -- no Low Voltage Programming > > pragma target MCLR external -- reset externally > > -- These configuration bit settings are only a selection, sufficient for > > -- this program, but other programs may need more or different settings. > > -- > > enable_digital_io() -- make all pins digital I/O > > -- > > -- Specify the pin to which the LED is connected. > > -- A low current (2 mA) led with 2.2K series resistor is recommended > > -- since not all pins may be able to drive an ordinary 20mA led. > > alias led is pin_A0 > > pin_A0_direction = output > > -- > > forever loop > > led = on > > _usec_delay(250_000) > > led = off > > _usec_delay(250_000) > > end loop > > > errors: > > Compilation started at :4/6/2012 1:52:27 AM > > jal 2.4l (compiled Aug 7 2009) > > [Error] (lib/16f88.jal) [Line 54] unexpected token: 'id' > > [Error] (lib/16f88.jal) [Line 54] "id" not defined > > [Error] (lib/16f88.jal) [Line 54] '=' expected (got '0x2000') > > [Error] (lib/16f88.jal) [Line 54] unexpected token: "0x2000" > > [Error] (16f88_blink.jal) [Line 32] unknown pragma target: osc > > [Error] (16f88_blink.jal) [Line 32] "osc" not defined > > [Error] (16f88_blink.jal) [Line 32] '=' expected (got 'hs') > > [Error] (16f88_blink.jal) [Line 32] "hs" not defined > > [Error] (16f88_blink.jal) [Line 32] '=' expected (got 'pragma') > > [Error] (16f88_blink.jal) [Line 33] unknown pragma target: wdt > > [Error] (16f88_blink.jal) [Line 33] "wdt" not defined > > [Error] (16f88_blink.jal) [Line 33] '=' expected (got 'disabled') > > [Error] (16f88_blink.jal) [Line 33] '=' expected (got 'pragma') > > [Error] (16f88_blink.jal) [Line 34] unknown pragma target: debug > > [Error] (16f88_blink.jal) [Line 34] "debug" not defined > > [Error] (16f88_blink.jal) [Line 34] '=' expected (got 'disabled') > > [Error] (16f88_blink.jal) [Line 34] '=' expected (got 'pragma') > > [Error] (16f88_blink.jal) [Line 35] unknown pragma target: lvp > > [Error] (16f88_blink.jal) [Line 35] "lvp" not defined > > [Error] (16f88_blink.jal) [Line 35] '=' expected (got 'disabled') > > [Error] (16f88_blink.jal) [Line 35] '=' expected (got 'pragma') > > [Error] (16f88_blink.jal) [Line 36] unknown pragma target: mclr > > [Error] (16f88_blink.jal) [Line 36] "mclr" not defined > > [Error] (16f88_blink.jal) [Line 36] '=' expected (got 'external') > > [Error] (16f88_blink.jal) [Line 36] "external" not defined > > [Error] (16f88_blink.jal) [Line 36] '=' expected (got 'enable_digital_io') > > [Error] (16f88_blink.jal) [Line 40] "enable_digital_io" not defined > > [Error] (16f88_blink.jal) [Line 45] "pin_a0" not defined > > [Error] (16f88_blink.jal) [Line 45] '=' expected (got 'pin_a0_direction') > > [Error] (16f88_blink.jal) [Line 46] "pin_a0_direction" not defined > > [Error] (16f88_blink.jal) [Line 49] "led" not defined > > 31 errors, 0 warnings > > Compiler CommandLine: > > C:\JALPack\compiler\jalv2.exe "C:\JALPack\project\PIC16F88 > > Blink\16f88_blink.jal" -s "C:\JALPack\lib" -no-variable-reuse > > > -- > > You received this message because you are subscribed to the Google Groups > > "jallib" group. > > To post to this group, send email to [email protected]. > > To unsubscribe from this group, send email to > > [email protected]. > > For more options, visit this group at > >http://groups.google.com/group/jallib?hl=en. -- You received this message because you are subscribed to the Google Groups "jallib" group. To post to this group, send email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/jallib?hl=en.
