Hello Rob, I don't think it will work. I need two ad inputs and pin_A2 is Vusb. I also don't understand why the programming pins are C0 and C1 instead of A0 and A1. regards hans
Op zaterdag 11 november 2023 om 17:02:34 UTC+1 schreef Rob CJ: > Hi Hans, > > I think you can. Is has sufficient ROM and RAM and a SPI interface. > > Kind regards, > > Rob > > ------------------------------ > *Van:* jal...@googlegroups.com <jal...@googlegroups.com> namens Hans van > Veldhuizen <hanz...@zeelandnet.nl> > *Verzonden:* zaterdag 11 november 2023 15:49 > > *Aan:* jallib <jal...@googlegroups.com> > *Onderwerp:* Re: [jallib] Camera_Gimbal > Hello Rob, > I have killed one of my 16F15325, is it possible to use the16F1455 for > this nrf24101 project? I have two of them. > Hans > > Op vrijdag 10 november 2023 om 08:17:30 UTC+1 schreef Hans van Veldhuizen: > > Hello Matthew, > More than 10 years ago I made Marieke with your lib, 8 servos and a very > expensive wireless command set > . (see https://youtu.be/U3uuH1cK8Dk) > I used a 16F1827 as transmitter and a 16F648a as receiver. I am now > trying to use this old set for this, but as always my old programs no > longer work in the changed JAL world. Time and again I experience that a > sample only works in that sample environment and as soon as I want to use > another PIC I have to complain to you. For me, electronics is still a tool > to achieve something and not a goal in itself. > I'll see what I can do with your advice, > Thank you > Hans > > Op vrijdag 10 november 2023 om 00:27:13 UTC+1 schreef Matthew Schinkel: > > Check your clock frequency. If it is half what it is supposed to be your > servo's would only get half pulses and half movement. > > Not sure if it helps here but I suggest you try the slip library sometime > for sending data packets. See samples 18f4620_slip_isr.jal > or 18f4620_slip_poll.jal. > > Matt. > > On Thursday, November 9, 2023 at 11:15:43 AM UTC-5 hanz...@zeelandnet.nl > wrote: > > Hi Mathew, > I've used your lib dozens of times on all kinds of servos and they always > worked perfectly!!!! These servos also work on the special tester that also > works on your lib. I'm pretty sure there is a conflict with the PIC here. > If I now go from 0 to max with the potentiometer, the servo only moves half > a turn. I just don't know what part of the frequency range they get. > In any case, very nice that you responded. > regards > Hans > > Op donderdag 9 november 2023 om 15:12:13 UTC+1 schreef Matthew Schinkel: > > Hi Hans, > > Servo's move depending on the PWM signal sent to them. It is possible your > servo's are expecting a different signal depending on the manufacturer. Do > you have other servo's to test? > > Do your servo's work correctly an un-modified Jallib sample? > > Do you have an oscilloscope you can test the signal with? The PWM signal > should be between 0.5ms and 2.5ms. > > Thanks, > Matt. > > On Wednesday, November 8, 2023 at 7:12:07 AM UTC-5 hanz...@zeelandnet.nl > wrote: > > I have now adapted both circuits for WiFi. (So the transmitter has a WiFi > master and the receiver a slave) > The data received is identical to the transmitter > . However, the servos only move half a turn. Apparently the Servo-lib > can't handle the pic. Or I have to set something else. The programs are > attached again. > > Op zaterdag 4 november 2023 om 10:50:22 UTC+1 schreef Hans van Veldhuizen: > > Hi Rob, > It has to do with the pin A2. If i change it to C2 the both are working > > Op zaterdag 4 november 2023 om 07:56:20 UTC+1 schreef Rob CJ: > > Hi Hans, > > The only difference that I see is the looptime. > > Instead of 1 second it is 1 ms but it depends on how fast the data is > received. If that is too fast will that disturb the servo movement? > > Kind regards, > > Rob > > > > ------------------------------ > *Van:* jal...@googlegroups.com <jal...@googlegroups.com> namens Hans van > Veldhuizen <hanz...@zeelandnet.nl> > *Verzonden:* vrijdag 3 november 2023 22:13 > *Aan:* jallib <jal...@googlegroups.com> > *Onderwerp:* Re: [jallib] Camera_Gimbal > > Have changed with attached basic. Same result. Changed 325 for 324 same > result > > Op vrijdag 3 november 2023 om 21:27:23 UTC+1 schreef Hans van Veldhuizen: > > Hi Rob, > If I add this before the original forever loop then just servo 2 moves. > Changed servo's same result > forever loop > > servo_move(60,1) > servo_move(60,2) > delay_1S(2) > > servo_move(150,1) > servo_move(150,2) > delay_1S(2) > > end loop > > Op vrijdag 3 november 2023 om 19:11:13 UTC+1 schreef Rob CJ: > > Hi Hans, > > I cannot see any errors. So the data is received correctly but the servo's > do not work? > > Have you tried to get the servo's working without the receive routines? So > just hard-code some values to see if the servo's are working? > > Kind regards, > > Rob > > > > ------------------------------ > *Van:* jal...@googlegroups.com <jal...@googlegroups.com> namens Hans van > Veldhuizen <hanz...@zeelandnet.nl> > *Verzonden:* donderdag 2 november 2023 13:09 > *Aan:* jallib <jal...@googlegroups.com> > *Onderwerp:* [jallib] Camera_Gimbal > > Hello all, > My question again. I'm trying to make a two-way camera Gimbal. I have > modified working programs. The transmitter now has two ADC inputs and the > receiver must control two servos. The signals arrive correctly at the > receiver in fits and starts. I can't get the servos to work. Attached are > the two files. > Please respond again, > regards > Hans > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to jallib+un...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/ff970ccd-ffb8-473f-991f-1441f768da3cn%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/ff970ccd-ffb8-473f-991f-1441f768da3cn%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to jallib+un...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/8093b573-4fb8-492a-ab0f-5db352424ffcn%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/8093b573-4fb8-492a-ab0f-5db352424ffcn%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to jallib+un...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/b592656c-ad20-4c53-a1f2-0557e960c26an%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/b592656c-ad20-4c53-a1f2-0557e960c26an%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to jallib+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/7d895e93-7337-448d-a123-a91d2afdb9d1n%40googlegroups.com.
