Hi Vasi, Wow, what a fantastic package! Very clever, and it's just missing the little bit I need! Too bad, but maybe someone else knows. By the way, I have a few UNOs here that I occasionally use to try out a program from the internet. But often, it doesn't work.
On Wednesday, I linked a program for the D1 mini V3 I ordered; let's hope it works. Then I can use a PIC instead of the pushbuttons and continue. https://github.com/gtmans/homewizard/blob/main/socketswitch/ApiSwitchDual-D1-git.ino Thanks for your reply and regards, Hans Op vrijdag 26 september 2025 om 17:31:52 UTC+2 schreef vasi vasi: > Hi Hans, > > Unfortunately, my knowledge does not contain the required information. > Many times ago I developed my own CMS (content manager system or blog) > written in PHP language and using a MySQL database, then later developed > some plug-ins for the sNewsCMS (porting also some Wordpress plugins for the > same system) but after a couple of years I got bored and decided that > further web programming is not something satisfying enough - that time, my > access to Internet was limited and expensive. I went back to PC programming > in other languages and then entered in the embedded world. Now I > gather/realize projects with ATmega micros in C, Wiring, LunaAVR and > GCBasic (maybe even FreePascal, not decided yet) languages for a book. > Probably, next is PICO, exactly what I recommended to you... Circuit Python > and Micro Python are unknown to me for now. I could go with C or FreePascal > but a future book is the main target. > > On Fri, Sep 26, 2025 at 5:49 PM Hans van Veldhuizen <[email protected]> > wrote: > >> HELLO Vasil, >> >> If I were 30 years younger, I would definitely embrace your proposal. >> Unfortunately, there are limits. >> >> Another question that you, with all your knowledge, can surely answer. >> >> When I open this on my PC, I get the correct data response from the >> Homewizard socket. >> >> http://<IP ADDRESS>/api/v1/data >> >> also http://<IP ADDRESS>/api/v1/state gives the correct answer >> >> The instruction I used also tells me how to get it to "ÖN", but I can't >> get it to work in a single line on my PC. >> >> http://<IP ADDRESS>/api/v1/state\ >> >> -X PUT\ >> >> -H "Content-Type: application/json"\ >> >> -d '{"power_on": true}' >> >> >> >> Perhaps you can do that and would like to tell me. >> >> Thanks in advance. >> >> Regards Hans >> >> Op vrijdag 26 september 2025 om 12:20:08 UTC+2 schreef vasi vasi: >> >>> Hans, >>> >>> It will be much easier for you to learn CircuitPython and use a >>> Raspberry Pi Pico board with WiFi support than torture yourself with Jal >>> and PIC... Then, along the way, you can migrate to MicroPython for >>> complete freedom and a plus of performance. >>> >>> I think this is the best long term solution for Jal users that cannot >>> learn C/C++/Wiring. I thought and searched for solutions and there is no >>> other solution better than this. There is FreePascal for Pico boards but it >>> has so limited support that you cannot call that a solution. >>> >>> If you cannot enter in the wonderful world of craftsmen using Arduino, >>> then skip it altogether for the next world that uses PICO boards with >>> CircuitPython. That is the future you are about to miss if chose not to >>> act. >>> >>> >>> https://learn.adafruit.com/networking-in-circuitpython/networking-with-the-wifi-module >>> >>> https://docs.circuitpython.org/en/latest/shared-bindings/wifi/index.html >>> >>> Ask ChatGPT to translate that source you linked to, into CircuitPython >>> source. See if it is easier for you to understand and use. Act accordingly. >>> >>> >>> On Thu, Sep 25, 2025 at 10:28 PM Hans van Veldhuizen < >>> [email protected]> wrote: >>> >>>> I found something I'd like to make but that's arduino again; >>>> >>>> https://github.com/gtmans/homewizard/blob/main/socketswitch/ApiSwitchDual-D1-git.ino >>>> >>>> Op woensdag 24 september 2025 om 18:19:54 UTC+2 schreef Hans van >>>> Veldhuizen: >>>> >>>>> Hi everyone, >>>>> Has anyone done anything with the D1 Mini V3.0.0 yet? >>>>> I found a lot of writing about the WEMOS D1 Mini V3.0.0, but that was >>>>> all in the Arduino world. This thing should also work with AT commands. >>>>> Curious! >>>>> Regards, >>>>> Hans >>>> >>>> -- >>>> You received this message because you are subscribed to the Google >>>> Groups "jallib" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to [email protected]. >>>> To view this discussion visit >>>> https://groups.google.com/d/msgid/jallib/d95b7f66-0a43-4bfd-bfa2-e054a1d028b9n%40googlegroups.com >>>> >>>> <https://groups.google.com/d/msgid/jallib/d95b7f66-0a43-4bfd-bfa2-e054a1d028b9n%40googlegroups.com?utm_medium=email&utm_source=footer> >>>> . >>>> >>> >>> >>> -- >>> Vasi >>> >> -- >> You received this message because you are subscribed to the Google Groups >> "jallib" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> > To view this discussion visit >> https://groups.google.com/d/msgid/jallib/934b98bb-3fa0-48c5-936d-9a14b850e81en%40googlegroups.com >> >> <https://groups.google.com/d/msgid/jallib/934b98bb-3fa0-48c5-936d-9a14b850e81en%40googlegroups.com?utm_medium=email&utm_source=footer> >> . >> > > > -- > Vasi > -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion visit https://groups.google.com/d/msgid/jallib/99ea143e-6cc5-4a37-a121-dbe6039716edn%40googlegroups.com.
