Hello, For the Cisco initiated LSP it seems like you are missing a configuration line. I'm not sure they it is mandatory, but worth checking: tunnel mpls traffic-eng path-option 1 dynamic.
As for the Juniper initiated LSP, can you try debugging RSVP on the Cisco side? Regards Amos On Apr 21, 2008, at 10:21 PM, Supanekar, Harsh V wrote: > Hi, > > Has anyone configured RSVP LSP between Juniper M series router and the > Cisco ISO SR series router. >> From the error message on the Juniper side (see below), it show >> that the > Cisco side is not configured for RSVP. > Does anyone have any ideas? > > Thanks > > > [EMAIL PROTECTED] run show mpls lsp detail > Ingress LSP: 1 sessions > > 20.20.20.1 > From: 10.20.20.1, State: Dn, ActiveRoute: 0, LSPname: j-c > ActivePath: (none) > LoadBalance: Random > Encoding type: Packet, Switching type: Packet, GPID: IPv4 > Primary State: Dn > SmartOptimizeTimer: 180 > 2 Apr 21 19:17:10.383 10.10.90.2: Non-RSVP capable router > detected[50 times] > Total 1 displayed, Up 0, Down 1 > > > CISCO CONFIGURATION > > mpls traffic-eng tunnels > > interface Tunnel1 > ip unnumbered Loopback10 > tunnel destination 10.20.20.1 > tunnel mode mpls traffic-eng > tunnel mpls traffic-eng autoroute announce > ! > interface Loopback10 > ip address 20.20.20.1 255.255.255.255 > ip ospf 1 area 0 > ! > interface GigabitEthernet0/0/0 > mtu 9178 > ip address 10.10.90.2 255.255.255.252 > ip ospf 1 area 0 > negotiation auto > mpls traffic-eng tunnels > mpls ip > no cdp enable > ip rsvp bandwidth > ip rsvp resource-provider none > > ! > router ospf 1 > log-adjacency-changes > mpls traffic-eng router-id Loopback10 > mpls traffic-eng area 0 > ! > > JUNIPER CONFIGURATION > > ge-0/2/0 { > mtu 9192; > unit 0 { > family inet { > address 10.10.90.1/30; > } > family mpls; > } > } > > lo0 { > unit 0 { > family inet { > address 10.20.20.1/32; > } > } > } > > routing-options { > static { > route 0.0.0.0/0 next-hop 10.10.90.2; > } > } > protocols { > rsvp { > interface ge-0/2/0.0; > } > mpls { > label-switched-path j-c { > to 20.20.20.1; > no-cspf; > } > interface ge-0/0/0.0; > interface ge-0/2/0.0; > } > ospf { > traffic-engineering; > area 0.0.0.0 { > interface ge-0/2/0.0; > interface lo0.0; > } > } > } > > > This e-mail and its attachments are confidential and solely for the > intended addressee(s). Do not share or use them without Fannie Mae's > approval. If received in error, contact the sender and delete them. > > > _______________________________________________ > juniper-nsp mailing list juniper-nsp@puck.nether.net > https://puck.nether.net/mailman/listinfo/juniper-nsp _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp