You'll need to install this module to run snmpwalk... Sorry http://www.net-snmp.org/
-Ben -----Original Message----- From: sunnyday [mailto:[EMAIL PROTECTED] Sent: Tuesday, June 24, 2008 3:51 AM To: Boyd, Benjamin R; juniper-nsp@puck.nether.net Subject: RE: [j-nsp] (no subject) I tried what you said with no result this is what I get: And also to tell you that it on junose not junos. C:\Documents and Settings\jet\Desktop\SNMPWALK_OCT31>snmpwalk.exe -v 2c -c pop-RO 192.168.30.238 ifOutOctets Cannot find module (IP-MIB): At line 0 in (none) Cannot find module (IF-MIB): At line 0 in (none) Cannot find module (TCP-MIB): At line 0 in (none) Cannot find module (UDP-MIB): At line 0 in (none) Cannot find module (SNMPv2-MIB): At line 0 in (none) Cannot find module (SNMPv2-SMI): At line 0 in (none) Cannot find module (UCD-SNMP-MIB): At line 0 in (none) Cannot find module (UCD-DEMO-MIB): At line 0 in (none) Cannot find module (SNMP-TARGET-MIB): At line 0 in (none) Cannot find module (SNMP-VIEW-BASED-ACM-MIB): At line 0 in (non Cannot find module (SNMP-COMMUNITY-MIB): At line 0 in (none) Cannot find module (UCD-DLMOD-MIB): At line 0 in (none) Cannot find module (SNMP-FRAMEWORK-MIB): At line 0 in (none) Cannot find module (SNMP-MPD-MIB): At line 0 in (none) Cannot find module (SNMP-USER-BASED-SM-MIB): At line 0 in (none Cannot find module (SNMP-NOTIFICATION-MIB): At line 0 in (none) Cannot find module (SNMPv2-TM): At line 0 in (none) ifOutOctets: (Sub-id not found: (top) -> ifOutOctets) C:\Documents and Settings\jet\Desktop\SNMPWALK_OCT31> -----Original Message----- From: Boyd, Benjamin R [mailto:[EMAIL PROTECTED] Sent: Monday, June 23, 2008 5:20 PM To: sunnyday; juniper-nsp@puck.nether.net Subject: RE: [j-nsp] (no subject) SunnyDay, I don't know the OID, but using snmpwalk.exe to find the outOctets you would use the following: snmpwalk.exe -v 1 -c "community" "device ip" ifOutOctets Which will give you output resembling: (mib.ifIndex = outOctets) ifOutOctets.35 = 3474330439 ifOutOctets.36 = 984860543 ifOutOctets.37 = 0 ifOutOctets.38 = 3450966616 >From here you'll have to find out the ifIndex of the interface you wish to view: In the juniper: show snmp mib walk ifDescr -Ben -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of sunnyday Sent: Monday, June 23, 2008 3:45 AM To: juniper-nsp@puck.nether.net Subject: [j-nsp] (no subject) Hello anyone knows the OID or how can I view the output of the command: Show egress-queue rates interface gigabitEthernet x/x/x Via SNMP? Thank you _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp ************************************************************************ **** *********** The information contained in this message, including attachments, may contain privileged or confidential information that is intended to be delivered only to the person identified above. If you are not the intended recipient, or the person responsible for delivering this message to the intended recipient, Windstream requests that you immediately notify the sender and asks that you do not read the message or its attachments, and that you delete them without copying or sending them to anyone else. *************************************************************************************** The information contained in this message, including attachments, may contain privileged or confidential information that is intended to be delivered only to the person identified above. If you are not the intended recipient, or the person responsible for delivering this message to the intended recipient, Windstream requests that you immediately notify the sender and asks that you do not read the message or its attachments, and that you delete them without copying or sending them to anyone else. _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp