Guys The problem was in FPC slot 7, which causes this alarm on the CB. We have found detination error after issuing show chassis fabric fpcs, then we made some diagnostics on FPC 7 shell mode and we found some errors.When changed the problem solved.
t...@router# run show chassis fabric summary Plane State Uptime 0 Spare 3 minutes, 52 seconds 1 Spare 3 minutes, 51 seconds 2 Check 23 minutes, 21 seconds 3 Online 23 minutes, 21 seconds 4 Online 23 minutes, 21 seconds 5 Online 23 minutes, 21 seconds t...@router# run show chassis fabric plane-location ------------Fabric Plane Locations------------- Plane 0 Control Board 0 Plane 1 Control Board 0 Plane 2 Control Board 1 Plane 3 Control Board 1 Plane 4 Control Board 2 Plane 5 Control Board 2 t...@router> show chassis fabric fpcs Fabric management FPC state FPC 7 PFE #0 Plane 0: Plane disabled Plane 1: Plane disabled Plane 2: Destination error Plane 3: Plane enabled Plane 4: Plane enabled Plane 5: Plane enabled PFE #2 Plane 0: Plane disabled Plane 1: Plane disabled Plane 2: Destination error Plane 3: Plane enabled Plane 4: Plane enabled Plane 5: Plane enabled BR, Walaa Abdel Razzak. -----Original Message----- From: Walaa Abdel razzak Sent: Wednesday, July 29, 2009 11:05 PM To: 'kyam...@nissho-ele.co.jp'; juniper-nsp@puck.nether.net Subject: RE: [j-nsp] MX960 SCB Alarm Hi The problem is not in the booting phase, but it's during switchover process. The alarm is cleared when taking the corresponding fabric plane offline then online. Best Regards, Walaa Abdel Razzak Senior Networks Engineer JNCIP-M Tel : +966147907 Fax: +96614790878 GSM : +966594366310 -----Original Message----- From: juniper-nsp-boun...@puck.nether.net [mailto:juniper-nsp-boun...@puck.nether.net] On Behalf Of kyam...@nissho-ele.co.jp Sent: Tuesday, July 28, 2009 8:41 PM To: juniper-nsp@puck.nether.net Subject: [j-nsp] MX960 SCB Alarm Hi I have experienced your issue ever. I guess you might meet this PR. NUMBER 408359 SEVERITY minor PRIORITY medium CATEGORY sw STATE closed SYNOPSIS MX SCB may fail to online at boot up sequence RELEASE 8.5R3.4; 9.3R1.7; 9.3R2.3; 9.3-20081208 COMMITTED-IN RELEASE 8.5R5; 9.3R3; 9.4R2 ARRIVAL DATE 2008-12-10 06:05:52 LAST MODIFIED 2009-05-08 14:45:20 CLOSE DATE 2009-03-03 20:38:48 RELEASE NOTE When you configure graceful Routing Engine switchover (GRES) on MX-series routers, the Switch Interface Board (SIB) might not initialize if you reboot both Routing Engines simultaneously or reboot a router with only one Routing Engine installed. This describes the boot sequesce of each RE. kazuhiro _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp __________ Information from ESET Smart Security, version of virus signature database 4223 (20090708) __________ The message was checked by ESET Smart Security. http://www.eset.com __________ Information from ESET Smart Security, version of virus signature database 4223 (20090708) __________ The message was checked by ESET Smart Security. http://www.eset.com __________ Information from ESET Smart Security, version of virus signature database 4223 (20090708) __________ The message was checked by ESET Smart Security. http://www.eset.com _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp