I didn't change cabling, but I connected a new interface to annother router and I'm having the same problem, the new interface is in the default configuration : set interfaces fe-0/3/2 unit 0 family inet address 10.0.24.2/30
ad...@m10> show interfaces terse Interface Admin Link Proto Local Remote ... fe-0/3/0 up up fe-0/3/0.123 up up inet 10.0.123.1/30 fe-0/3/0.32767 up up fe-0/3/1 up up fe-0/3/1.123 up up inet 10.0.123.2/30 fe-0/3/1.32767 up up fe-0/3/2 up up fe-0/3/2.0 up up inet 10.0.24.2/30 fe-0/3/3 up up any idea guys ? BR // Mounir On Tue, Dec 21, 2010 at 7:25 PM, Cristian Frizziero cristian.frizzi...@iquall.net wrote: > Hi!! > > I'd try to change ports pairs, and to switch the PIC to a different fpc > slot, just to be sure that there is no hardware issue.... > > The configuration looks fine.... > > Cristian > > > > > > > > > > El 21/12/2010 15:07, juniper light escribió: > > Hi guys, > I would like to use M10 to simulate 3 PE, using logical-routers ( Junos > 8.4R4.2 ) > > I connected 2 fastethernet back-to-back, link are UP. but when I tried > configuring vlan-id , I cannot ping from one Logical router to the other : > > first scenario using Vlan-tagging : > > set logical-routers PE2 interfaces fe-0/3/0 unit 23 vlan-id 123 > set logical-routers PE2 interfaces fe-0/3/0 unit 23 family inet > address10.0.123.1/30 > set logical-routers PE3 interfaces fe-0/3/1 unit 23 vlan-id 123 > set logical-routers PE3 interfaces fe-0/3/1 unit 23 family inet > address10.0.123.2/30 > set interfaces fe-0/3/0 vlan-tagging > set interfaces fe-0/3/1 vlan-tagging > > ad...@m10> show interfaces terse > Interface Admin Link Proto Local Remote > ... > fe-0/3/0 up up > fe-0/3/0.123 up up inet 10.0.123.1/30 > fe-0/3/0.32767 <http://10.0.123.1/30fe-0/3/0.32767> up up > fe-0/3/1 up up > fe-0/3/1.123 up up inet 10.0.123.2/30 > fe-0/3/1.32767 <http://10.0.123.2/30fe-0/3/1.32767> up up > fe-0/3/2 up up > fe-0/3/3 up up > > Second scenario without Vlan-tagging : > > set logical-routers PE2 interfaces fe-0/3/0 unit 0 family inet > address10.0.123.1/30 > set logical-routers PE3 interfaces fe-0/3/1 unit 0 family inet > address10.0.123.2/30 > > > ad...@m10> ping logical-router PE2 10.0.123.2 source 10.0.123.1 > PING 10.0.123.2 (10.0.123.2): 56 data bytes > nothing happen ...... > > ad...@m10> show interfaces terse > Interface Admin Link Proto Local Remote > ... > fe-0/3/0 up up > fe-0/3/0.0 up up inet 10.0.123.1/30 > fe-0/3/1 <http://10.0.123.1/30fe-0/3/1> up up > fe-0/3/1.0 up up inet 10.0.123.2/30 > fe-0/3/2 <http://10.0.123.2/30fe-0/3/2> up up > fe-0/3/3 up up > > > ad...@m10 > > show chassis hardware > Hardware inventory: > Item Version Part number Serial number Description > Chassis xxxx M10 > Midplane REV 03 710-001950 xxx M10 Backplane > Power Supply A Rev 05 740-002497 xxx AC Power Supply > Display REV 04 710-001995 xxx M10 Display Board > Routing Engine REV 07 740-007603 xxx RE-3.0 > FEB REV 08 710-003310 xx E-FEB > FPC 0 E-FPC > PIC 1 REV 05 750-003163 xxx 1x G/E, 1000 BASE-SX > PIC 3 REV 06 750-002992 xxx 4x F/E, 100 BASE-TX > FPC 1 E-FPC > Fan Tray Rear Left Fan Tray > > Any idea about that ? > > Thanks for your help, > > Kind Regards > // Mounir > _______________________________________________ > juniper-nsp mailing list > juniper-...@puck.nether.nethttps://puck.nether.net/mailman/listinfo/juniper-nsp > > _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp