Ops , but it did not work either Nand format failed BR, Mohammad
On Sun, 11 Nov 2018 at 14:46, Jonas Frey <j...@probe-networks.de> wrote: > Hi Mohammad, > > thats a typo, its nand_format (note the underscore). > Am Sonntag, den 11.11.2018, 05:31 -0500 schrieb Mohammad Khalil: > > => reset > > > > > > U-Boot 1.1.6-JNPR-2.7 (Build time: Nov 26 2013 - 19:04:49) > > > > Initializing memory this may take some time... > > Measured DDR clock 266.62 MHz > > SRX_100H2 board revision major:1, minor:0, serial #: BZ4214AF1453 > > OCTEON CN5020-SCP pass 1.1, Core clock: 500 MHz, DDR clock: 266 MHz > > (532 > > Mhz data rate) > > DRAM: 2048 MB > > Starting Memory POST... > > Checking datalines... OK > > Checking address lines... OK > > Checking 512K memory for U-Boot... OK. > > Running U-Boot CRC Test... OK. > > Flash: 4 MB > > USB: scanning bus for devices... 4 USB Device(s) found > > scanning bus for storage devices... Read Error for > > STMicroelectronics device 0 > > Not intializing this device, disabling autoboot > > Device may need formatting, please issue command : > > <nand_format> at console prompt to format > > 2 Storage Device(s) found > > Clearing DRAM........ done > > BIST check passed. > > Boot Media: nand-flash usb > > Net: pic init done (err = 0)octeth0 > > POST Passed > > Press SPACE to abort autoboot in 1 seconds > > => nand-format > > Unknown command 'nand-format' - try 'help' > > > > > > On Sun, 11 Nov 2018 at 04:17, Muhammad Atif Jauhar <atif.jauhar@gmail > > .com> > > wrote: > > > > > > > > Hi Khalil, > > > > > > Kindly follow below link to recover it. > > > > > > > > > https://forums.juniper.net/t5/SRX-Services-Gateway/Boot-problem-of- > > > UBoot-srx240-having-status-LED-red/td-p/211103 > > > > > > Regards, > > > > > > Muhammad Atif Jauhar > > > (+966-56-00-04-985) > > > > > > > > > On Sun, Nov 11, 2018 at 11:36 AM Mohammad Khalil <eng.m...@gmail.co > > > m> > > > wrote: > > > > > > > > > > > Hello all > > > > I have my Juniper SRX 100h stuck in the u-boot mode > > > > I have tried to download a new image on a USB stick , plugged it > > > > into the > > > > device and tried to upgrade with no luck > > > > Looked around but could not find a solution , anyone can help > > > > please? > > > > > > > > BR, > > > > Mohammad > > > > _______________________________________________ > > > > juniper-nsp mailing list juniper-nsp@puck.nether.net > > > > https://puck.nether.net/mailman/listinfo/juniper-nsp > > > > > > _______________________________________________ > > juniper-nsp mailing list juniper-nsp@puck.nether.net > > https://puck.nether.net/mailman/listinfo/juniper-nsp > _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp
