This change was made by a bot.
** Changed in: linux (Ubuntu)
Status: New => Confirmed
--
You received this bug notification because you are a member of Kernel
Packages, which is subscribed to linux in Ubuntu.
https://bugs.launchpad.net/bugs/1510560
Title:
package linux-image-3.19.0-31-generic (not installed) failed to
install/upgrade: subprocess new pre-installation script returned error
exit status 128
Status in linux package in Ubuntu:
Confirmed
Bug description:
cat /proc/version_signature > version.log produces
Ubuntu 3.19.0-30.34-generic 3.19.8-ckt6
and sudo lspci -vnvn > lspci-vnvn.log produces
00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v2/Ivy Bridge DRAM
Controller [8086:0158] (rev 09)
Subsystem: Dell Device [1028:04dd]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
Kernel driver in use: ie31200_edac
00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset
Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 04) (prog-if 20 [EHCI])
Subsystem: Dell Device [1028:04dd]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at c5106000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci-pci
00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset
Family PCI Express Root Port 1 [8086:1c10] (rev b4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: c0000000-c3ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal+
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x4, ASPM L0s L1, Exit
Latency L0s <512ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #0, PowerLimit 25.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna+
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF
Not Supported ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-,
OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB,
EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-,
LinkEqualizationRequest-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: feeff00c Data: 4171
Capabilities: [90] Subsystem: Dell Device [1028:04dd]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset
Family USB Enhanced Host Controller #1 [8086:1c26] (rev 04) (prog-if 20 [EHCI])
Subsystem: Dell Device [1028:04dd]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at c5105000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e]
(rev a4) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
Memory behind bridge: c4800000-c50fffff
Prefetchable memory behind bridge: 00000000c4000000-00000000c47fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Dell Device [1028:04dd]
00:1f.0 ISA bridge [0601]: Intel Corporation C202 Chipset Family LPC
Controller [8086:1c52] (rev 04)
Subsystem: Dell Device [1028:04dd]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
Kernel driver in use: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series
Chipset Family SATA AHCI Controller [8086:1c02] (rev 04) (prog-if 01 [AHCI 1.0])
Subsystem: Dell Device [1028:04dd]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 25
Region 0: I/O ports at 2048 [size=8]
Region 1: I/O ports at 2054 [size=4]
Region 2: I/O ports at 2040 [size=8]
Region 3: I/O ports at 2050 [size=4]
Region 4: I/O ports at 2020 [size=32]
Region 5: Memory at c5104000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0300c Data: 41c1
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family
SMBus Controller [8086:1c22] (rev 04)
Subsystem: Dell Device [1028:04dd]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 6
Region 0: Memory at c5102000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 2000 [size=32]
01:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme II BCM5716
Gigabit Ethernet [14e4:163b] (rev 20)
Subsystem: Dell Device [1028:04dd]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at c0000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: Broadcom NetXtreme II Ethernet Controller
Read-only fields:
[PN] Part number: BCM95716C1
[EC] Engineering changes: 220197-3
[SN] Serial number: 0123456789
[MN] Manufacture ID: 31 30 32 38
[V0] Vendor specific: 7.4.8
[RV] Reserved: checksum good, 23 byte(s) reserved
End
Capabilities: [58] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [a0] MSI-X: Enable+ Count=9 Masked-
Vector table: BAR=0 offset=0000c000
PBA: BAR=0 offset=0000e000
Capabilities: [ac] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <4us, L1
<64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Exit
Latency L0s <2us, L1 <2us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-,
OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-,
OBFF Disabled
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB,
EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-,
LinkEqualizationRequest-
Capabilities: [100 v1] Device Serial Number d4-ae-52-ff-fe-ca-d4-d4
Capabilities: [110 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP+ SDES- TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+
RxOF+ MalfTLP+ ECRC+ UnsupReq+ ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [150 v1] Power Budgeting <?>
Capabilities: [160 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: bnx2
01:00.1 Ethernet controller [0200]: Broadcom Corporation NetXtreme II BCM5716
Gigabit Ethernet [14e4:163b] (rev 20)
Subsystem: Dell Device [1028:04dd]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at c2000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: Broadcom NetXtreme II Ethernet Controller
Read-only fields:
[PN] Part number: BCM95716C1
[EC] Engineering changes: 220197-3
[SN] Serial number: 0123456789
[MN] Manufacture ID: 31 30 32 38
[V0] Vendor specific: 7.4.8
[RV] Reserved: checksum good, 23 byte(s) reserved
End
Capabilities: [58] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [a0] MSI-X: Enable+ Count=9 Masked-
Vector table: BAR=0 offset=0000c000
PBA: BAR=0 offset=0000e000
Capabilities: [ac] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <4us, L1
<64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Exit
Latency L0s <2us, L1 <2us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-,
OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-,
OBFF Disabled
LnkSta2: Current De-emphasis Level: -6dB,
EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-,
LinkEqualizationRequest-
Capabilities: [100 v1] Device Serial Number d4-ae-52-ff-fe-ca-d4-d5
Capabilities: [110 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP+ SDES- TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+
RxOF+ MalfTLP+ ECRC+ UnsupReq+ ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [150 v1] Power Budgeting <?>
Capabilities: [160 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: bnx2
02:03.0 VGA compatible controller [0300]: Matrox Electronics Systems Ltd. MGA
G200eW WPCM450 [102b:0532] (rev 0a) (prog-if 00 [VGA controller])
Subsystem: Dell Device [1028:04dd]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (4000ns min, 8000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 6
Region 0: Memory at c4000000 (32-bit, prefetchable) [size=8M]
Region 1: Memory at c5000000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at c4800000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at c5010000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
ProblemType: Package
DistroRelease: Ubuntu 15.04
Package: linux-image-3.19.0-31-generic (not installed)
ProcVersionSignature: Ubuntu 3.19.0-30.34-generic 3.19.8-ckt6
Uname: Linux 3.19.0-30-generic x86_64
ApportVersion: 2.17.2-0ubuntu1.5
Architecture: amd64
AudioDevicesInUse: Error: command ['fuser', '-v', '/dev/snd/seq',
'/dev/snd/timer'] failed with exit code 1:
Date: Tue Oct 27 14:13:03 2015
DuplicateSignature: package:linux-image-3.19.0-31-generic:(not
installed):subprocess new pre-installation script returned error exit status 128
ErrorMessage: subprocess new pre-installation script returned error exit
status 128
HibernationDevice: RESUME=UUID=991604dc-4921-4ba6-a8fc-2ba08df4a56d
InstallationDate: Installed on 2015-10-19 (8 days ago)
InstallationMedia: Ubuntu 15.04 "Vivid Vervet" - Release amd64 (20150422)
IwConfig:
eth0 no wireless extensions.
eth1 no wireless extensions.
lo no wireless extensions.
MachineType: Dell Inc. PowerEdge R210 II
ProcFB: 0 EFI VGA
ProcKernelCmdLine: BOOT_IMAGE=/boot/vmlinuz-3.19.0-30-generic.efi.signed
root=UUID=40e178f4-c0f6-4193-9818-28376de6e6f5 ro quiet splash vt.handoff=7
PulseList: Error: command ['pacmd', 'list'] failed with exit code 1: No
PulseAudio daemon running, or not running as session daemon.
RelatedPackageVersions: grub-pc N/A
RfKill:
SourcePackage: linux
Title: package linux-image-3.19.0-31-generic (not installed) failed to
install/upgrade: subprocess new pre-installation script returned error exit
status 128
UdevLog: Error: [Errno 2] No such file or directory: '/var/log/udev'
UpgradeStatus: No upgrade log present (probably fresh install)
dmi.bios.date: 05/09/2013
dmi.bios.vendor: Dell Inc.
dmi.bios.version: 2.4.3
dmi.board.name: 03X6X0
dmi.board.vendor: Dell Inc.
dmi.board.version: A03
dmi.chassis.type: 23
dmi.chassis.vendor: Dell Inc.
dmi.modalias:
dmi:bvnDellInc.:bvr2.4.3:bd05/09/2013:svnDellInc.:pnPowerEdgeR210II:pvr:rvnDellInc.:rn03X6X0:rvrA03:cvnDellInc.:ct23:cvr:
dmi.product.name: PowerEdge R210 II
dmi.sys.vendor: Dell Inc.
To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1510560/+subscriptions
--
Mailing list: https://launchpad.net/~kernel-packages
Post to : kernel-packages@lists.launchpad.net
Unsubscribe : https://launchpad.net/~kernel-packages
More help : https://help.launchpad.net/ListHelp
