I upgraded my system to Ubuntu 22.04 and sadly, this issue does impact that version also :(
I have setup a bond, to try and get the wifi to be used after a reboot, but it's not very reliable, so I have to physically disconnect and re- connect the USB ethernet every time the computer reboots, or power cycles. I found a much simpler way to reproduce the problem, that does not require rebooting. I was trying to see if I could "simulate" a disconnect somehow and came across this: https://unix.stackexchange.com/questions/276352/disable-a-usb-port-in-linux link@woody:~> lspci -k| grep -i usb -A2 00:14.0 USB controller: Intel Corporation Sunrise Point-LP USB 3.0 xHCI Controller (rev 21) Subsystem: Acer Incorporated [ALI] Sunrise Point-LP USB 3.0 xHCI Controller Kernel driver in use: xhci_hcd Kernel modules: xhci_pci echo "0000:00:14.0" | sudo tee /sys/bus/pci/drivers/xhci_hcd/unbind echo "0000:00:14.0" | sudo tee /sys/bus/pci/drivers/xhci_hcd/bind I get all of this as the controller comes back online. [447821.011157] xhci_hcd 0000:00:14.0: xHCI Host Controller [447821.011178] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1 [447821.012331] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000081109810 [447821.015401] xhci_hcd 0000:00:14.0: xHCI Host Controller [447821.015421] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2 [447821.015436] xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed [447821.015591] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15 [447821.015605] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [447821.015613] usb usb1: Product: xHCI Host Controller [447821.015621] usb usb1: Manufacturer: Linux 5.15.0-141-generic xhci-hcd [447821.015628] usb usb1: SerialNumber: 0000:00:14.0 [447821.016229] hub 1-0:1.0: USB hub found [447821.016281] hub 1-0:1.0: 12 ports detected [447821.019232] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.15 [447821.019236] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [447821.019238] usb usb2: Product: xHCI Host Controller [447821.019239] usb usb2: Manufacturer: Linux 5.15.0-141-generic xhci-hcd [447821.019240] usb usb2: SerialNumber: 0000:00:14.0 [447821.019347] hub 2-0:1.0: USB hub found [447821.019362] hub 2-0:1.0: 6 ports detected [447821.353581] usb 2-1: new SuperSpeed USB device number 2 using xhci_hcd [447821.374034] usb 2-1: New USB device found, idVendor=2537, idProduct=1068, bcdDevice= 1.00 [447821.374048] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [447821.374054] usb 2-1: Product: NS1068 [447821.374059] usb 2-1: Manufacturer: Norelsys [447821.374064] usb 2-1: SerialNumber: 0123456789ABCDE [447821.375435] usb-storage 2-1:1.0: USB Mass Storage device detected [447821.375795] usb-storage 2-1:1.0: Quirks match for vid 2537 pid 1068: 800000 [447821.375939] scsi host3: usb-storage 2-1:1.0 [447821.501420] usb 1-5: new full-speed USB device number 2 using xhci_hcd [447821.652213] usb 1-5: New USB device found, idVendor=04ca, idProduct=3016, bcdDevice= 0.01 [447821.652230] usb 1-5: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [447821.781429] usb 1-6: new full-speed USB device number 3 using xhci_hcd [447821.933038] usb 1-6: New USB device found, idVendor=04f3, idProduct=2561, bcdDevice=57.11 [447821.933054] usb 1-6: New USB device strings: Mfr=4, Product=14, SerialNumber=0 [447821.933061] usb 1-6: Product: Touchscreen [447821.933067] usb 1-6: Manufacturer: ELAN [447821.946704] input: ELAN Touchscreen Stylus as /devices/pci0000:00/0000:00:14.0/usb1/1-6/1-6:1.0/0003:04F3:2561.0006/input/input42 [447821.947277] input: ELAN Touchscreen as /devices/pci0000:00/0000:00:14.0/usb1/1-6/1-6:1.0/0003:04F3:2561.0006/input/input43 [447821.947752] input: ELAN Touchscreen UNKNOWN as /devices/pci0000:00/0000:00:14.0/usb1/1-6/1-6:1.0/0003:04F3:2561.0006/input/input44 [447821.947967] input: ELAN Touchscreen UNKNOWN as /devices/pci0000:00/0000:00:14.0/usb1/1-6/1-6:1.0/0003:04F3:2561.0006/input/input45 [447821.948427] hid-multitouch 0003:04F3:2561.0006: input,hiddev0,hidraw1: USB HID v1.10 Device [ELAN Touchscreen] on usb-0000:00:14.0-6/input0 [447822.073432] usb 1-7: new high-speed USB device number 4 using xhci_hcd [447822.230405] usb 1-7: New USB device found, idVendor=04f2, idProduct=b5f7, bcdDevice=92.26 [447822.230420] usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [447822.230428] usb 1-7: Product: HD WebCam [447822.230433] usb 1-7: Manufacturer: Chicony Electronics Co.,Ltd. [447822.234796] usb 1-7: Found UVC 1.00 device HD WebCam (04f2:b5f7) [447822.259994] input: HD WebCam: HD WebCam as /devices/pci0000:00/0000:00:14.0/usb1/1-7/1-7:1.0/input/input47 [447822.385536] usb 1-8: new high-speed USB device number 5 using xhci_hcd [447822.534472] usb 1-8: New USB device found, idVendor=0bda, idProduct=0129, bcdDevice=39.60 [447822.534487] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [447822.534494] usb 1-8: Product: USB2.0-CRW [447822.534500] usb 1-8: Manufacturer: Generic [447822.534505] usb 1-8: SerialNumber: 20100201396000000 [447822.665487] usb 1-9: new full-speed USB device number 6 using xhci_hcd [447822.817061] usb 1-9: New USB device found, idVendor=04f3, idProduct=0c03, bcdDevice= 1.43 [447822.817075] usb 1-9: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [447822.817081] usb 1-9: Product: ELAN:Fingerprint [447822.817086] usb 1-9: Manufacturer: ELAN [447822.916341] scsi 3:0:0:0: Direct-Access ATA WDC WD3200BEVT-6 1A13 PQ: 0 ANSI: 6 [447822.916601] sd 3:0:0:0: Attached scsi generic sg1 type 0 [447822.916825] sd 3:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB) [447822.917310] sd 3:0:0:0: [sdb] Write Protect is off [447822.917313] sd 3:0:0:0: [sdb] Mode Sense: 43 00 00 00 [447822.917586] sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [447822.963602] sdb: sdb1 [447822.964445] sd 3:0:0:0: [sdb] Attached SCSI disk But no USB Ethernet. I have to physically disconnect and re-connect it to get this. [447881.733044] usb 2-3: new SuperSpeed USB device number 3 using xhci_hcd [447881.753811] usb 2-3: New USB device found, idVendor=0bda, idProduct=8153, bcdDevice=30.00 [447881.753825] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=6 [447881.753832] usb 2-3: Product: USB 10/100/1000 LAN [447881.753837] usb 2-3: Manufacturer: Realtek [447881.753841] usb 2-3: SerialNumber: 000027 [447881.885609] r8152-cfgselector 2-3: reset SuperSpeed USB device number 3 using xhci_hcd [447881.927159] r8152 2-3:1.0: load rtl8153a-4 v2 02/07/20 successfully [447881.954062] r8152 2-3:1.0 eth0: v1.12.13 [447881.984216] r8152 2-3:1.0 enx00e04c681327: renamed from eth0 [447882.024100] bond0: (slave enx00e04c681327): making interface the new active one [447882.024297] bond0: (slave enx00e04c681327): Enslaving as an active interface with an up link [447885.895787] r8152 2-3:1.0 enx00e04c681327: carrier on -- You received this bug notification because you are a member of Kernel Packages, which is subscribed to linux in Ubuntu. https://bugs.launchpad.net/bugs/2092711 Title: USB Ethernet adapter does not show up on boot Status in linux package in Ubuntu: New Bug description: I have a USB Ethernet adapter that worked fine in Ubuntu 20.04, and 22.04, but has stopped working in 24.04. On boot, lsusb does not show the device at all, and none of the relevant drivers are loaded into the kernel. If I unplug the device and re-insert it, then it works, but this is awfully inconvenient as this should be the primary/only network interface for this machine. ProblemType: Bug DistroRelease: Ubuntu 24.04 Package: linux-image-6.8.0-51-generic 6.8.0-51.52 ProcVersionSignature: Ubuntu 6.8.0-51.52-generic 6.8.12 Uname: Linux 6.8.0-51-generic x86_64 NonfreeKernelModules: wl AlsaVersion: Advanced Linux Sound Architecture Driver Version k6.8.0-51-generic. AplayDevices: Error: [Errno 2] No such file or directory: 'aplay' ApportVersion: 2.28.1-0ubuntu3.3 Architecture: amd64 ArecordDevices: Error: [Errno 2] No such file or directory: 'arecord' AudioDevicesInUse: Error: command ['fuser', '-v', '/dev/snd/timer', '/dev/snd/seq', '/dev/snd/pcmC0D0p', '/dev/snd/pcmC0D0c', '/dev/snd/pcmC0D3p', '/dev/snd/pcmC0D7p', '/dev/snd/pcmC0D8p', '/dev/snd/hwC0D0', '/dev/snd/hwC0D2', '/dev/snd/controlC0', '/dev/snd/by-path'] failed with exit code 1: CRDA: N/A Card0.Amixer.info: Error: [Errno 2] No such file or directory: 'amixer' Card0.Amixer.values: Error: [Errno 2] No such file or directory: 'amixer' CasperMD5CheckResult: unknown Date: Mon Dec 30 17:14:32 2024 HibernationDevice: MachineType: Acer Spin SP513-52N ProcFB: 0 i915drmfb ProcKernelCmdLine: BOOT_IMAGE=/boot/vmlinuz-6.8.0-51-generic root=UUID=d0275542-8c36-43af-b0a4-4500d57070f5 ro noplymouth RelatedPackageVersions: linux-restricted-modules-6.8.0-51-generic N/A linux-backports-modules-6.8.0-51-generic N/A linux-firmware 20240318.git3b128b60-0ubuntu2.6 RfKill: Error: [Errno 2] No such file or directory: 'rfkill' SourcePackage: linux UpgradeStatus: Upgraded to noble on 2024-12-30 (0 days ago) dmi.bios.date: 04/18/2019 dmi.bios.release: 1.15 dmi.bios.vendor: Insyde Corp. dmi.bios.version: V1.15 dmi.board.name: Woody_KL dmi.board.vendor: KBL dmi.board.version: V1.15 dmi.chassis.type: 31 dmi.chassis.vendor: Acer dmi.chassis.version: V1.15 dmi.ec.firmware.release: 1.9 dmi.modalias: dmi:bvnInsydeCorp.:bvrV1.15:bd04/18/2019:br1.15:efr1.9:svnAcer:pnSpinSP513-52N:pvrV1.15:rvnKBL:rnWoody_KL:rvrV1.15:cvnAcer:ct31:cvrV1.15:sku0000000000000000: dmi.product.family: Spin 5 dmi.product.name: Spin SP513-52N dmi.product.sku: 0000000000000000 dmi.product.version: V1.15 dmi.sys.vendor: Acer --- ProblemType: Bug AlsaVersion: Advanced Linux Sound Architecture Driver Version k6.8.0-51-generic. AplayDevices: Error: [Errno 2] No such file or directory: 'aplay' ApportVersion: 2.28.1-0ubuntu3.3 Architecture: amd64 ArecordDevices: Error: [Errno 2] No such file or directory: 'arecord' AudioDevicesInUse: Error: command ['fuser', '-v', '/dev/snd/timer', '/dev/snd/seq', '/dev/snd/pcmC0D0p', '/dev/snd/pcmC0D0c', '/dev/snd/pcmC0D3p', '/dev/snd/pcmC0D7p', '/dev/snd/pcmC0D8p', '/dev/snd/hwC0D0', '/dev/snd/hwC0D2', '/dev/snd/controlC0', '/dev/snd/by-path'] failed with exit code 1: CRDA: N/A Card0.Amixer.info: Error: [Errno 2] No such file or directory: 'amixer' Card0.Amixer.values: Error: [Errno 2] No such file or directory: 'amixer' CasperMD5CheckResult: unknown DistroRelease: Ubuntu 24.04 HibernationDevice: MachineType: Acer Spin SP513-52N NonfreeKernelModules: wl Package: linux (not installed) ProcFB: 0 i915drmfb ProcKernelCmdLine: BOOT_IMAGE=/boot/vmlinuz-6.8.0-51-generic root=UUID=d0275542-8c36-43af-b0a4-4500d57070f5 ro noplymouth ProcVersionSignature: Ubuntu 6.8.0-51.52-generic 6.8.12 RelatedPackageVersions: linux-restricted-modules-6.8.0-51-generic N/A linux-backports-modules-6.8.0-51-generic N/A linux-firmware 20240318.git3b128b60-0ubuntu2.6 RfKill: Error: [Errno 2] No such file or directory: 'rfkill' Tags: noble Uname: Linux 6.8.0-51-generic x86_64 UpgradeStatus: Upgraded to noble on 2024-12-30 (0 days ago) UserGroups: N/A _MarkForUpload: True dmi.bios.date: 04/18/2019 dmi.bios.release: 1.15 dmi.bios.vendor: Insyde Corp. dmi.bios.version: V1.15 dmi.board.name: Woody_KL dmi.board.vendor: KBL dmi.board.version: V1.15 dmi.chassis.type: 31 dmi.chassis.vendor: Acer dmi.chassis.version: V1.15 dmi.ec.firmware.release: 1.9 dmi.modalias: dmi:bvnInsydeCorp.:bvrV1.15:bd04/18/2019:br1.15:efr1.9:svnAcer:pnSpinSP513-52N:pvrV1.15:rvnKBL:rnWoody_KL:rvrV1.15:cvnAcer:ct31:cvrV1.15:sku0000000000000000: dmi.product.family: Spin 5 dmi.product.name: Spin SP513-52N dmi.product.sku: 0000000000000000 dmi.product.version: V1.15 dmi.sys.vendor: Acer To manage notifications about this bug go to: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/2092711/+subscriptions -- Mailing list: https://launchpad.net/~kernel-packages Post to : [email protected] Unsubscribe : https://launchpad.net/~kernel-packages More help : https://help.launchpad.net/ListHelp
