Andrew Theurer wrote:
I've been looking at how KVM handles windows guests, and I am a little
concerned with the CPU overhead. My test case is as follows:
I am running 4 instances of a J2EE benchmark. Each instance needs one
application server and one DB server. 8 VMs in total are used.
I have the same App and DB software for Linux and Windows (and same
versions) so I can compare between Linux and Windows. I also have
another hypervisor which I can test both Windows and Linux VMs.
The host has EPT capable processors. VMs in KVM are backed with large
pages.
Test results:
Config CPU utilization
------ -----
KVM-85
Windows Server 2008 64-bit VMs 44.84
RedHat 5.3 w/ 2.6.29 64-bit VMs 24.56
Other-Hypervisor
Windows Server 2008 64-bit VMs 30.63
RedHat 5.3 w/ 2.6.18 64-bit VMs 27.13
-KVM running Windows VMs uses 46% more CPU than the Other-Hypervisor
-The Other-Hypervisor provides an optimized virtual network driver
-KVM results listed above did not use virtio_net or virtio_disk for
Windows, but do for Linux
-One extra KVM run (not listed above) was made with virtio_net for
Windows VMs but only reduced CPU by 2%
I think the publicly available driver is pretty old and unoptimized.
-Most of the CPU overhead could be attributed to the DB VMs, where
there is about 5 MB/sec writes per VM
-I don't have a virtio_block driver for Windows to test. Does one exist?
Exists, not public though.
-All tests above had 2 vCPUS per VM
Here's a comparison of kvm_stat between Windows (run1) and Linux (run2):
run1 run2 run1/run2
---- ---- ---------
efer_relo: 0 0 1
exits : 1206880 121916 9.899
total exits is the prime measure of course.
fpu_reloa: 210969 20863 10.112
halt_exit: 15092 13222 1.141
halt_wake: 14466 9294 1.556
host_stat: 211066 45117 4.678
host state reloads measure (approximately) exits to userspace, likely
due to the unoptimized drivers.
hypercall: 0 0 1
insn_emul: 119582 38126 3.136
again lack of drivers
insn_emul: 0 0 1
invlpg : 0 0 1
io_exits : 131051 26349 4.974
ditto
irq_exits: 8128 12937 0.628
irq_injec: 29955 21825 1.373
irq_windo: 2504 2022 1.238
kvm_reque: 0 0 1
largepage: 1 64 0.009
mmio_exit: 59224 0 Inf
wow, linux avoids mmio completely. good.
10x the number of exits, a problem?
_the_ problem.
I happened to try just one vCPU per VM for KVM/Windows VMs, and I was
surprised how much of a difference it made:
Config CPU utilization
------ -----
KVM-85
Windows Server 2008 64-bit VMs, 2 vCPU per VM 44.84
Windows Server 2008 64-bit VMs, 1 vCPU per VM 36.44
A 19% reduction in CPU utilization vs KVM/Windows-2vCPU! Does not
explain all the overhead (vs Other-Hypervisor, 2 vCPUs per VM) but,
that sure seems like a lot between 1 to 2 vCPUs for KVM/Windows-VMs.
Inter-process communication is expensive. Marcelo added some
optimizations (the sending vcpu used to wait for the target vcpu, now
they don't). They're in kvm-86 (of course). You'll need 2.6.26+ on the
host for them to take effect (of course, for many features, the more
recent the host the faster kvm on top can run).
Windows 2008 also implements some hypervisor accelerations which are
especially useful on smp. Gleb has started some work on this. I don't
know if other_hypervisor implements them.
Finally, smp is expensive! data moves across caches, processors wait for
each other, etc.
I have not run with 1 vCPU per VM with Other-Hypervisor, but I will
soon. Anyway, I also collected kvm_stat for the 1 vCPU case, and here
it is compared to KVM/Linux VMs with 2 vCPUs:
run1 run2 run1/run2
---- ---- ---------
efer_relo: 0 0 1
exits : 1184471 121916 9.715
Still see the huge difference in vm_exits, so I guess not all is great
yet.
Yeah, exit rate stayed the same, so it's probably IPC costs and
intrinsic smp costs.
So, what would be the best course of action for this?
Is there a virtio_block driver to test?
There is, but it isn't available yet.
Can we find the root cause of the exits (is there a way to get stack
dump or something that can show where there are coming from)?
Marcelo is working on a super-duper easy to use kvm trace which can show
what's going on. The old one is reasonably easy though it exports less
data. If you can generate some traces, I'll have a look at them.
P.S. Here is the qemu cmd line for the windows VMs:
/usr/local/bin/qemu-system-x86_64 -name newcastle-xdbt01 -hda
/dev/disk/by-id/scsi-3600a0b80000f1eb10000074f4a02b08a
Use: -drive /dev/very-long-name,cache=none instead of -hda to disable
the host cache. Won't make much of a differnence for 5 MB/s though.
--
Do not meddle in the internals of kernels, for they are subtle and quick to
panic.
--
To unsubscribe from this list: send the line "unsubscribe kvm" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html