Hi Spiders.  I thought I would take a break from the slow progress on my 
Chantilly fan and make a post.

   When adding in a pair of bobbins at the gimp in point ground lace 
(Chantilly, Bucks Point),  should I add in a pair of bobbins or 2 single 
bobbins? Does 
it matter?
   A pair of bobbins is two bobbins connected together.  You make a pair by 
taking a long piece of thread and winding half on one bobbin and half on the 
other bobbin.  Then you hang the pair over the gimp and, presto, it's added in.
  A single bobbin is a bobbin wound with thread which ends in a loose thread 
end.  You add this by attaching the loose thread end to the gimp and letting 
the bobbin hang.  While the bobbin merrily works its way through the lace, the 
loose end stays with the gimp until the gimp has worked three or four 
"stitches".  Then the loose end is thrown back, later cut off close to the lace.
   The obvious way to attach the loose end to the gimp is to knot the loose 
end to the loose end of a spare bobbin--to give yourself a leash--and attach 
the spare bobbin to the gimp bobbin (or just remember to work them as one 
unit). 
 Then throw back the spare bobbin before you reach the knot.

  I think it must be better to add in a pair of bobbins, since then there are 
no loose ends in the lace.  Surely it is bad to have loose ends in the lace.  
Even though they've been secured by three ot four stitches, won't they tend 
to unravel over time and so cause the whole lace piece to fall apart?  I would 
always add in pairs if it wasn't for the problem of winding thread.
  Here is the problem.  Suppose you start out with a pair of bobbins with 
each bobbin's having a good amount of thread.  This pair works through the lace 
for a while and eventually is thrown out and cut off.  Now you come to a place 
where you need to add bobbins.  The obvious bobbins to add are the ones that 
were cut off.  But now your original long unbroken piece of thread has been cut 
in half (half is now on each bobbin) so instead of a long unbroken thread you 
have two threads each half the size of the original thread.  So you discard 
one thread and share the other between the two bobbins.  Now you have a pair 
with each bobbin's having a not-so-good amount of thread.  Perhaps now the 
bobbins have too little thread and you'll have to, ugh, replace them when they 
run 
out of thread (that puts loose threads into the lace again!).
  I could just throw out lots and lots of thread and always put long pieces 
of thread on pairs of bobbins, so the thread problem is not unsurmountable.  
But it is unpleasant to constantly be throwing out thread and winding bobbins.
  If I add in single bobbins then there is no winding at all to be done.  I 
just grab the bobbin and add it in.

  So you see that I would like the convenience of adding in bobbins as 
singles, but I am afraid that that is a bad idea because of all the loose ends. 
 
It's bad enough that I have dozens of loose ends from cutting off bobbins, 
without also having them from adding in.
  What is the common wisdom on this question?
  
  This is a new problem for me.  I have been learning lace from Nottingham's 
_Technique_Of_Bobbins_Lace_Revised_Edition_ (excellent book for learning lace) 
and in the Bucks Point exercises that I've done so far (I've done 2/3 or so 
of them) only one or two pairs have ever been added in.  I didn't mind adding 
in the bobbins as pairs when there were only one or two of them.  However in my 
Chantilly fan (the fan from Lohr's _Hausdragon_ box of patterns), pairs are 
constantly being cut off and added in.  A pair--if not two pairs-- is added in 
whenever a half stitch figure is started and cut off when the the figure ends. 
 It got to be really burdensome, constantly endlessly rewinding bobbins do as 
to add them in as pairs.  I got sick of it.

  I am almost half-way done with my fan!  This is slow progress since it is 
the only piece of lace I work on and it's been several months.  It is full of 
mistakes.  The mistakes in the figures are particularly noticeable since a 
mistake in half-stitch causes a "run in the stocking".  I used to think, how 
could 
anybody make a mistake in half-sttich?  Half-stitch mistakes are so easy to 
catch.  Ha Ha.  I got my comeuppance.  Also I notice the ragged and gappy look 
of the borders of the figure due to putting pins in the worng pinholes or 
maybe pricking the holes badly.  Less noticeable is the fact that I just can't 
seem to fix in my mind how many twists to use in footside and so just twist 
randomly.
  Fortunately, it turns out that I don't care about the mistakes.  No, I look 
at the lace, my heart lifts up,  and I think it is beautiful.  Just as flower 
can be beautiful without being perfect.  However, I am really worried that my 
lace will fall apart because of all the loose ends.  I am constantly cutting 
off bobbins and I don't know if I secure the ends well enough before I throw 
them back and cut off close to the lace.   I won't be able to tell until I take 
the lace off of the pillow, months from now, and give the threads a few weeks 
or months to unwork themselves.  Silk is apparently a pretty unmanagable sort 
of thread, so I think that means it's extra likely that the threads will work 
loose.
                                                                 --  Julie    
 Baltimore, MD

-
To unsubscribe send email to [EMAIL PROTECTED] containing the line:
unsubscribe lace [EMAIL PROTECTED] For help, write to
[EMAIL PROTECTED]

Reply via email to