Hi,
I've successfully installed snv_69 on nc6320 with Intel 945GM. While it
basically works I have some issues:
[b]1. I get 1280x1024 resolution instead of 1400x1050[/b]
Manually generating xorg.conf (Xorg --configure) and adding Modes
"1400x1050" doesn't help.
Fortunately, thanks to Mike Baranczak, I managed to get 1400x1050. Just
downloaded
915resolution tool from http://wallwrestling.ath.cx/915resolution/ and
run './915resolution 38
1400x1050' and restarted Xorg without xorg.conf - now it picked up
1400x1050 by itself.
However it should have worked automatically without any external tools.
Is it being worked on?
Some entries from Xorg.log
(II) I810(0): Creating default Display subsection in Screen section
"Builtin Default i810 Screen 0" for depth/fbbpp 24/32
(++) I810(0): Depth 24, (--) framebuffer bpp 32
(==) I810(0): RGB weight 888
(==) I810(0): Default visual is TrueColor
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/X11/lib/modules/amd64//libint10.so
(II) I810(0): initializing int10
(WW) I810(0): Bad V_BIOS checksum
(II) I810(0): Primary V_BIOS segment is: 0xc000
(II) I810(0): VESA BIOS detected
(II) I810(0): VESA VBE Version 3.0
(II) I810(0): VESA VBE Total Mem: 7872 kB
(II) I810(0): VESA VBE OEM: Intel(r) 82945GM Chipset Family Graphics Chip
Accelerated VGA BIOS
(II) I810(0): VESA VBE OEM Software Rev: 1.0
(II) I810(0): VESA VBE OEM Vendor: Intel Corporation
(II) I810(0): VESA VBE OEM Product: Intel(r) 82945GM Chipset Family Graphics
Controller
(II) I810(0): VESA VBE OEM Product Rev: Hardware Version 0.0
(II) I810(0): Integrated Graphics Chipset: Intel(R) 945GM
(--) I810(0): Chipset: "945GM"
(--) I810(0): Linear framebuffer at 0xD0000000
(--) I810(0): IO registers at addr 0xE8400000
(II) I810(0): 2 display pipes available.
(II) I810(0): detected 7932 kB stolen memory.
(II) GARTInit: /dev/agpgart opened successfully
(II) I810(0): xf86AcquireGART: AGPIOC_ACQUIRE succeeded
(II) I810(0): xf86ReleaseGART: AGPIOC_RELEASE succeeded
(II) I810(0): I830CheckAvailableMemory: 257900 kB available
(II) I810(0): Will try to reserve 32768 kiB of AGP aperture space
for the DRM memory manager.
(II) I810(0): Monitoring connected displays enabled
(II) I810(0): Will attempt to tell the BIOS that there is 12288 kB VideoRAM
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/X11/lib/modules/amd64//libint10.so
(II) I810(0): initializing int10
(WW) I810(0): Bad V_BIOS checksum
(II) I810(0): Primary V_BIOS segment is: 0xc000
(II) I810(0): VESA BIOS detected
(II) I810(0): VESA VBE Version 3.0
(II) I810(0): VESA VBE Total Mem: 12288 kB
(II) I810(0): VESA VBE OEM: Intel(r) 82945GM Chipset Family Graphics Chip
Accelerated VGA BIOS
(II) I810(0): VESA VBE OEM Software Rev: 1.0
(II) I810(0): VESA VBE OEM Vendor: Intel Corporation
(II) I810(0): VESA VBE OEM Product: Intel(r) 82945GM Chipset Family Graphics
Controller
(II) I810(0): VESA VBE OEM Product Rev: Hardware Version 0.0
(II) I810(0): BIOS now sees 12288 kB VideoRAM
(--) I810(0): Pre-allocated VideoRAM: 7932 kByte
(==) I810(0): VideoRAM: 65536 kByte
(==) I810(0): video overlay key set to 0x101fe
(**) I810(0): page flipping disabled
(==) I810(0): Using gamma correction (1.0, 1.0, 1.0)
(II) I810(0): BIOS Build: 1305
(==) I810(0): Device Presence: disabled.
(==) I810(0): Display Info: enabled.
(II) I810(0): Broken BIOSes cause the system to hang here.
If you encounter this problem please add
Option "DisplayInfo" "FALSE"
to the Device section of your XF86Config file.
(II) I810(0): Display Info: CRT: attached: FALSE, present: TRUE, size: (720,400)
(II) I810(0): Display Info: TV: attached: FALSE, present: TRUE, size: (1024,768)
(II) I810(0): Display Info: DFP (digital flat panel): attached: FALSE, present:
FALSE, size: (0,2059)
(II) I810(0): Display Info: LFP (local flat panel): attached: TRUE, present:
TRUE, size: (1400,1050)
(II) I810(0): Display Info: Second (second CRT): attached: FALSE, present:
FALSE, size: (0,2059)
(II) I810(0): Display Info: TV2 (second TV): attached: FALSE, present: FALSE,
size: (0,2059)
(II) I810(0): Display Info: DFP2 (second digital flat panel): attached: FALSE,
present: FALSE, size: (0,2059)
(II) I810(0): Display Info: LFP2 (second local flat panel): attached: FALSE,
present: FALSE, size: (0,2059)
(II) I810(0): Size of device LFP (local flat panel) is 1400 x 1050
(II) I810(0): No active displays on Pipe A.
(II) I810(0): Currently active displays on Pipe B:
(II) I810(0): LFP (local flat panel)
(II) I810(0): Lowest common panel size for pipe B is 1400 x 1050
(==) I810(0): Display is using Pipe B
(--) I810(0): Maximum frambuffer space: 65368 kByte
(II) I810(0): VESA VBE PanelID read successfully
(II) I810(0): PanelID returned panel resolution : 1400x1050
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Loading /usr/X11/lib/modules/amd64//libddc.so
(II) Module ddc: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 1.1
(II) I810(0): VESA VBE DDC supported
(II) I810(0): VESA VBE DDC Level 2
(II) I810(0): VESA VBE DDC transfer in appr. 1 sec.
(II) I810(0): VESA VBE DDC read successfully
(II) I810(0): Manufacturer: CMO Model: 1508 Serial#: 0
(II) I810(0): Year: 2004 Week: 53
(II) I810(0): EDID Version: 1.3
(II) I810(0): Digital Display Input
(II) I810(0): Max H-Image Size [cm]: horiz.: 30 vert.: 23
(II) I810(0): Gamma: 2.20
(II) I810(0): No DPMS capabilities specified; RGB/Color Display
(II) I810(0): First detailed timing is preferred mode
(II) I810(0): redX: 0.590 redY: 0.340 greenX: 0.317 greenY: 0.536
(II) I810(0): blueX: 0.298 blueY: 0.119 whiteX: 0.312 whiteY: 0.328
(II) I810(0): Supported VESA Video Modes:
(II) I810(0): 1024x768 at 60Hz
(II) I810(0): Manufacturer's mask: 0
(II) I810(0): Supported additional Video Mode:
(II) I810(0): clock: 108.0 MHz Image Size: 304 x 228 mm
(II) I810(0): h_active: 1400 h_sync: 1448 h_sync_end 1560 h_blank_end 1688
h_border: 0
(II) I810(0): v_active: 1050 v_sync: 1053 v_sync_end 1057 v_blanking: 1066
v_border: 0
(II) I810(0): N150P5
(II) I810(0): CMO
(II) I810(0): Monitor name: N150P5-L01
(II) I810(0): EDID (in hex):
(II) I810(0): 00ffffffffffff000daf081500000000
(II) I810(0): 350e0103801e17780a0560975751894c
(II) I810(0): 1e505400080001010101010101010101
(II) I810(0): 010101010101302a7820511a10403070
(II) I810(0): 340030e410000018000000fe004e3135
(II) I810(0): 3050350a202020202020000000fe0043
(II) I810(0): 4d4f0a202020202020202020000000fc
(II) I810(0): 004e31353050352d4c30310a202000de
(II) I810(0): Printing DDC gathered Modelines:
(II) I810(0): Modeline "1024x768" 65.00 1024 1048 1184 1344 768 771 777 806
-hsync -vsync
(II) I810(0): Modeline "1400x1050" 108.00 1400 1448 1560 1688 1050 1053 1057
1066 -hsync -vsync
(--) I810(0): A non-CRT device is attached to pipe B.
No refresh rate overrides will be attempted.
(--) I810(0): Maximum space available for video modes: 12288 kByte
[...]
(II) I810(0): Builtin Default Monitor: Using hsync range of 60.00-66.32 kHz
(II) I810(0): Builtin Default Monitor: Using vrefresh value of 60.00 Hz
(WW) I810(0): Unable to estimate virtual size
(II) I810(0): xf86AcquireGART: AGPIOC_ACQUIRE succeeded
(II) I810(0): Increasing the scanline pitch to allow tiling mode (1280 -> 2048).
(--) I810(0): Virtual size is 1280x1024 (pitch 2048)
(**) I810(0): *Built-in mode "1280x1024"
(**) I810(0): Display dimensions: (300, 230) mm
(**) I810(0): DPI set to (108, 113)
[b]2. DRI is not working - at least that's what I'm getting in Xorg.log
[/b]
from Xorg.log
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/X11/lib/modules/amd64//libint10.so
(II) I810(0): initializing int10
(WW) I810(0): Bad V_BIOS checksum
(II) I810(0): Primary V_BIOS segment is: 0xc000
(II) I810(0): VESA BIOS detected
(II) I810(0): VESA VBE Version 3.0
(II) I810(0): VESA VBE Total Mem: 7872 kB
(II) I810(0): VESA VBE OEM: Intel(r) 82945GM Chipset Family Graphics Chip
Accelerated VGA BIOS
(II) I810(0): VESA VBE OEM Software Rev: 1.0
(II) I810(0): VESA VBE OEM Vendor: Intel Corporation
(II) I810(0): VESA VBE OEM Product: Intel(r) 82945GM Chipset Family Graphics
Controller
(II) I810(0): VESA VBE OEM Product Rev: Hardware Version 0.0
(II) I810(0): Allocated 128 kB for the ring buffer at 0x0
(II) I810(0): Allocating at least 256 scanlines for pixmap cache
(II) I810(0): Initial framebuffer allocation size: 12288 kByte
(II) I810(0): Allocated 4 kB for HW cursor at 0xdfff000 (0x31ec7000)
(II) I810(0): Allocated 16 kB for HW (ARGB) cursor at 0xdffb000 (0x03f47000)
(II) I810(0): Allocated 4 kB for Overlay registers at 0xdffa000 (0x342d3000).
(II) I810(0): Allocated 64 kB for the scratch buffer at 0xdfea000
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device or address)
drmOpenDevice: open result is -1, (No such device or address)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device or address)
drmOpenDevice: open result is -1, (No such device or address)
drmOpenDevice: Open failed
[drm] failed to load kernel module "i915"
(II) I810(0): [drm] drmOpen failed
(EE) I810(0): [dri] DRIScreenInit failed. Disabling DRI.
(II) I810(0): 859730: Memory at offset 0x00020000, size 12288 kBytes
(II) I810(0): 838930: Memory at offset 0x0dfff000, size 4 kBytes
(II) I810(0): 8389d0: Memory at offset 0x0dffb000, size 16 kBytes
(II) I810(0): 94a9e8: Memory at offset 0x00000000, size 128 kBytes
(II) I810(0): 8597b0: Memory at offset 0x0dfea000, size 64 kBytes
(II) I810(0): 838a20: Memory at offset 0x0dffa000, size 4 kBytes
(II) I810(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(WW) I810(0): Extended BIOS function 0x5f05 failed.
(II) I810(0): xf86BindGARTMemory: bind key 4 at 0x007bf000 (pgoffset 1983)
(II) I810(0): xf86BindGARTMemory: bind key 0 at 0x0dfff000 (pgoffset 57343)
(II) I810(0): xf86BindGARTMemory: bind key 1 at 0x0dffb000 (pgoffset 57339)
(II) I810(0): xf86BindGARTMemory: bind key 3 at 0x0dfea000 (pgoffset 57322)
(II) I810(0): xf86BindGARTMemory: bind key 2 at 0x0dffa000 (pgoffset 57338)
(--) I810(0): A non-CRT device is attached to pipe B.
No refresh rate overrides will be attempted.
(II) I810(0): Display plane A is disabled and connected to Pipe A.
(II) I810(0): Display plane B is enabled and connected to Pipe B.
(II) I810(0): Enabling plane B.
(II) I810(0): Display plane A is now disabled and connected to Pipe A.
(II) I810(0): Display plane B is now enabled and connected to Pipe B.
(II) I810(0): PIPEACONF is 0x00000000
(II) I810(0): PIPEBCONF is 0x80000000
(II) I810(0): Mode bandwidth is 78 Mpixel/s
(II) I810(0): maxBandwidth is 1152 Mbyte/s, pipe bandwidths are 420 Mbyte/s, 0
Mbyte/s
(II) I810(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
8x8 mono pattern filled rectangles
Indirect CPU to Screen color expansion
Solid Horizontal and Vertical Lines
Offscreen Pixmaps
Setting up tile and stipple cache:
16 128x128 slots
4 256x256 slots
(==) I810(0): Backing store disabled
(==) I810(0): Silken mouse disabled
(II) I810(0): Initializing HW Cursor
(II) I810(0): Enabling Xvideo one-line mode
(II) I810(0): Set up overlay video
(II) I810(0): Set up textured video
(II) I810(0): direct rendering: Failed
(II) I810(0): RandR enabled, ignore the following RandR disabled message.
(II) I810(0): Rotating to 0 degrees
(--) RandR disabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension XAccessControlExtension
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(II) Initializing built-in extension LGE
(EE) AIGLX: Screen 0 is not DRI capable
[b]3. Gnone-Terminal[/b]
Default setting, freshly installed system. If I type something I often
get some garbage under and behind the cursor - especially if I use backspace.
I've also noticed it on snv_67 with Intel 915G.
Is it a known bug?
[b]4. During system start I get below messages - what is it about?[/b]
pci_autoconfig: [ID 769584 kern.warning] WARNING: detected unsupported
configuration: non-empty bridge (bus 0x0, dev
0x1c, func 0x0) without I/O resources assigned by bios for secondary bus 0x8
pci_autoconfig: [ID 130646 kern.warning] WARNING: devices under bridge bus 0x0,
dev 0x1c, func 0x0 will not be assig
ned I/O ports
[b]5. And another messages - I guess 64bit driver is missing, and sound is not
working (it's not).
unix: [ID 469452 kern.info] NOTICE: cpqhpc: 64-bit driver module not found[/b]
audiosup: [ID 533774 kern.warning] WARNING: audiohd0: unsupported HD codec:
vid=0x11d41981, rev=0x00100200
audiosup: [ID 108418 kern.warning] WARNING: audiohd0: unsupported HD codec:
vid=0x11c13026, rev=0x00100700
audiosup: [ID 493330 kern.warning] WARNING: audiohd0: audiohd_attach() couldn't
create codec
This message posted from opensolaris.org
