If Senao, I recommend to flash it with 1.5.6 firmware.
mgg wrote:
Hello there, while subscribing to the mail list it would be appreciated if you could help here.
I'm using Advantech SBC 9574 with celeron 333.
The board has BX chipset and compact flash slot and secondary ide drive.
Anyway I'm running WISP-DISt ( latest one ) with Cisco and older aironet cards with no problem ( not a single one ).
Right now I'm setting up Senao card in PC104 to pcmcia adapter ( it is a Vadem chipset with two PCMCia slots... here is cardctl out :
Socket 0: product info: "INTERSIL", "HFA384x/IEEE", "Version 01.02", "" manfid: 0x0156, 0x0002 function: 6 (network) Socket 1: no product info available
I had a little trouble setting up the card to be active since it is a 5.0 volt pcmcia slot so I had to uncomment in /etc/pcmcia/hostap_cs.conf line :
ignore_cis_vcc=33
After that everything vent smooth ... the card is up and running.
I have set it up as a AP and successfully connected another WISP-dist machine with Cisco card ... ping works and I was happy :) .
So I have moved to testing the link ... run some ttcp tests ... but after a while on average loads and even after I leave the ping on Cisco card after night the Cisco dissconects and I get this ...
netcs0 IEEE 802.11-DS ESSID:"test" Mode:Master Tx-Power=20 dBm Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0
and dmesg shows :
ostap_cs: netcs0 Tx timed out! NETDEV WATCHDOG: netcs0: transmit timed out hostap_cs: netcs0 Tx timed out! NETDEV WATCHDOG: netcs0: transmit timed out hostap_cs: netcs0 Tx timed out! NETDEV WATCHDOG: netcs0: transmit timed out hostap_cs: netcs0 Tx timed out! NETDEV WATCHDOG: netcs0: transmit timed out hostap_cs: netcs0 Tx timed out! NETDEV WATCHDOG: netcs0: transmit timed out hostap_cs: netcs0 Tx timed out! NETDEV WATCHDOG: netcs0: transmit timed out hostap_cs: netcs0 Tx timed out! NETDEV WATCHDOG: netcs0: transmit timed out hostap_cs: netcs0 Tx timed out! NETDEV WATCHDOG: netcs0: transmit timed out hostap_cs: netcs0 Tx timed out! NETDEV WATCHDOG: netcs0: transmit timed out hostap_cs: netcs0 Tx timed out!
after I restart the networking in wispdist menu I get the working Ap with iwconfig :
netcs0 IEEE 802.11-DS ESSID:"test" Mode:Master Frequency:2.422GHz Access Point: 00:02:6F:31:1C:53 Bit Rate:2Mb/s Tx-Power=20 dBm Sensitivity=1/0 Retry min limit:8 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Why is this happening ??? After i finish these lines I'll try to set up a new CPU 533 or higher, since board takes P III up to a 933 Mhz but i doubt this will help since load is normal.
Any ideas ?
Thanks Igor
-- Best Regards, Vladimir Ivashchenko ThunderWorx - www.thunderworx.com Senior Systems Designer/Engineer
-------------------------------------------------------
This SF.Net email is sponsored by: Oracle 10g
Get certified on the hottest thing ever to hit the market... Oracle 10g. Take an Oracle 10g class now, and we'll give you the exam FREE. http://ads.osdn.com/?ad_id=3149&alloc_id=8166&op=click
_______________________________________________
leaf-wisp-dist mailing list
[EMAIL PROTECTED]
https://lists.sourceforge.net/lists/listinfo/leaf-wisp-dist
