The HNET C108 (http://www.szhwtech88.com/Product-product-cid-100-id-4374.html) is a mifi based on MT7602A, which has the following specifications:
* CPU: MT7620A * 1x 10/100Mbps Ethernet. * 16 MB Flash. * 64 MB RAM. * 1x USB 2.0 port. * 1x mini-PCIe slots. * 1x SIM slots. * 1x 2.4Ghz WIFI. * 1x button. * 6000 mAh battery. * 5x controllable LEDs. Works: * Wifi. * Switch. * mini-PCIe slot. Only tested with a USB device (a modem). * SIM slot. * Sysupgrade. * Button (reset). Not working: * USB port. * Wifi LED. It is always switched on. Not tested: * SD card reader. Notes: * The C108 has no dedicated status LED. I therefore set the LAN LED as status LED. * By default, both the LAN and Wifi interface has the same MAC address. The factory firmware sets the MAC address of the Wifi interface to (LAN + 2) in order to avoid having the same MAC. I did not find an easy way to accomplish this using the existing LEDE infrastructure. Instead, I implemented the opposite, i.e., the MAC address of the LAN interface is increased by two. * In commit 77645ffcd9ad767be02ea6d5cfe042928a3565d1, the mode of 01_leds was set to 0644. This patch changes that back 0755. Installation: The router comes pre-installed with OpenWRT, including a variant of Luci. The initial firmware install can be done through this UI, following normal procedure. I.e., access the UI and update the firmware using the sysupgrade-image. Remember to select that you do not want to keep existing settings. Recovery: If you brick the device, the C108 supports recovery using TFTP. Keep the reset button pressed for ~5sec when booting to trigger TFTP. Set the address of the network interface on your machine to 10.10.10.3/24, and rename your image file to Kernal.bin. Signed-off-by: Kristian Evensen <kristian.even...@gmail.com> --- target/linux/ramips/base-files/etc/board.d/01_leds | 4 + .../linux/ramips/base-files/etc/board.d/02_network | 5 + target/linux/ramips/base-files/etc/diag.sh | 3 + target/linux/ramips/base-files/lib/ramips.sh | 3 + .../ramips/base-files/lib/upgrade/platform.sh | 1 + target/linux/ramips/dts/C108.dts | 182 +++++++++++++++++++++ target/linux/ramips/image/mt7620.mk | 8 + 7 files changed, 206 insertions(+) mode change 100644 => 100755 target/linux/ramips/base-files/etc/board.d/01_leds create mode 100644 target/linux/ramips/dts/C108.dts diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds old mode 100644 new mode 100755 index ff5d156f2c..83e1a94000 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -82,6 +82,10 @@ broadway) set_usb_led "$board:red:diskmounted" set_wifi_led "$board:red:wps_active" ;; +c108) + ucidef_set_led_netdev "lan" "lan" "$board:green:lan" "eth0" + ucidef_set_led_netdev "modem" "modem" "$board:green:modem" "wwan0" + ;; c20i) ucidef_set_led_switch "lan" "lan" "$board:blue:lan" "switch0" "0x1e" ucidef_set_led_switch "wan" "wan" "$board:blue:wan" "switch0" "0x01" diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index df70a8b2ec..273a0a75c9 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -217,6 +217,7 @@ ramips_setup_interfaces() ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "9@eth0" ;; + c108|\ cf-wr800n) ucidef_add_switch "switch0" \ "4:lan" "6t@eth0" @@ -386,6 +387,10 @@ ramips_setup_macs() lan_mac=$(cat /sys/class/net/eth0/address) wan_mac=$(mtd_get_mac_binary devdata 7) ;; + c108) + lan_mac=$(cat /sys/class/net/eth0/address) + lan_mac=$(macaddr_add "$lan_mac" 2) + ;; cy-swr1100|\ dch-m225) lan_mac=$(mtd_get_mac_ascii factory lanmac) diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh index 960e189283..7b267a6854 100644 --- a/target/linux/ramips/base-files/etc/diag.sh +++ b/target/linux/ramips/base-files/etc/diag.sh @@ -296,6 +296,9 @@ get_status_led() { zbt-wg3526-32M) status_led="zbt-wg3526:green:status" ;; + c108) + status_len="$board:green:lan" + ;; esac } diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh index fe66a87c2e..174e29e434 100755 --- a/target/linux/ramips/base-files/lib/ramips.sh +++ b/target/linux/ramips/base-files/lib/ramips.sh @@ -85,6 +85,9 @@ ramips_board_detect() { *"Broadway") name="broadway" ;; + *"C108") + name="c108" + ;; *"C20i") name="c20i" ;; diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh index 3cb1d19a28..5cfca52ab1 100755 --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh @@ -29,6 +29,7 @@ platform_check_image() { awm002-evb-8M|\ bc2|\ broadway|\ + c108|\ carambola|\ cf-wr800n|\ cs-qr10|\ diff --git a/target/linux/ramips/dts/C108.dts b/target/linux/ramips/dts/C108.dts new file mode 100644 index 0000000000..c8f57ed949 --- /dev/null +++ b/target/linux/ramips/dts/C108.dts @@ -0,0 +1,182 @@ +/* + * BSD LICENSE + * + * Copyright(c) 2017 Kristian Evensen <kristian.even...@gmail.com>. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * * Neither the name of Broadcom Corporation nor the names of its + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +/dts-v1/; + +#include "mt7620a.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + compatible = "hnet,c108", "ralink,mt7620a-soc"; + model = "HNET C108"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + gpio-export { + compatible = "gpio-export"; + #size-cells = <0>; + + power_modem { + gpio-export,name = "power_modem"; + gpio-export,output = <GPIO_ACTIVE_LOW>; + gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + sdcard { + label = "c108:green:sdcard"; + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; + }; + + modem_green { + label = "c108:green:modem"; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + }; + + modem_red { + label = "c108:red:modem"; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; + + lan_red { + label = "c108:red:lan"; + gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>; + }; + + lan_green { + label = "c108:green:lan"; + gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <20>; + + reset { + label = "reset"; + gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + }; + }; +}; + +&gpio1 { + status = "okay"; +}; + +&gpio2 { + status = "okay"; +}; + +&gpio3 { + status = "okay"; +}; + +&spi0 { + status = "okay"; + + en25q128@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x30000 0x10000>; + read-only; + }; + + factory: partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + }; + + partition@50000 { + label = "firmware"; + reg = <0x50000 0xfb0000>; + }; + }; +}; + +&sdhci { + status = "okay"; +}; + +&ehci { + status = "okay"; +}; + +&ohci { + status = "okay"; +}; + +ðernet { + mtd-mac-address = <&factory 0x4>; + mediatek,portmap = "l"; +}; + +&wmac { + ralink,mtd-eeprom = <&factory 0>; +}; + +&pinctrl { + state_default: pinctrl0 { + default { + ralink,group = "i2c", "uartf", "spi refclk", "ephy"; + ralink,function = "gpio"; + }; + }; +}; + +&pcie { + status = "okay"; +}; diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk index f9a9fdb84c..0061a018b9 100644 --- a/target/linux/ramips/image/mt7620.mk +++ b/target/linux/ramips/image/mt7620.mk @@ -62,6 +62,14 @@ define Device/ArcherMR200 endef TARGET_DEVICES += ArcherMR200 +define Device/c108 + DTS := C108 + IMAGE_SIZE := $(ralink_default_fw_size_16M) + DEVICE_TITLE := HNET C108 + DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-sdhci-mt7620 +endef +TARGET_DEVICES += c108 + define Device/cf-wr800n DTS := CF-WR800N DEVICE_TITLE := Comfast CF-WR800N -- 2.11.0 _______________________________________________ Lede-dev mailing list Lede-dev@lists.infradead.org http://lists.infradead.org/mailman/listinfo/lede-dev