I do have a duplicate set of gears (the gold ones), crank, etc. I believe were for the original IRT-33. The silver plated gears are for the MA. I could sell you the IRT-33 gold gears, etc. if you like. I'll take a picture of what I have for the IRT so you can see what you would be getting. once you've seen the picture, we can work out what would be a reasonable price. In terms of the felt wheel it is a 6" dia, 1" thick wheel. I'll probably keep that to do finish buffing.
Date: Sat, 24 Jan 2015 13:28:21 -0500
From: mwfos...@earthlink.net
To: legacy-ornamental-mills@googlegroups.com
Subject: Re: New Owner of a Woodchuck MA - Need documentation
Mike,
Three questions:
1. How is it that "Oklahoma" Mike is living near Milwaukee? (Shouldn't you
now be "Milwaukee Mike"?)
2. If you have extra parts that you will not be needing/using, I will probably
be interested in some of them. Specifically, I am in need of a set of the
drive(?) gears - the ones identified on the LOM headstock as "A" thru "G".
They appear to be the ones shown in the top/first picture in your email.
Will you be willing to sell me these gears?
3. In the last picture, in the lower right corner, there is what appears to be
a round thick felt disk - with a hole in its center. What is its diameter and
thickness?
If it is about 6" diameter, I may be interested in it as well.
Thanks.
Mac
-----Original Message-----
From: "Okla Mike (Liltwisted)"
Sent: Jan 24, 2015 11:25 AM
To: legacy-ornamental-mills@googlegroups.com
Subject: Re: New Owner of a Woodchuck MA - Need documentation
Looks like I will be able to get you a manual soon,
Just bought the one listed on Craigs List. More to come.
Mike
OK
On 10/9/2014 9:48 PM, Tim Krause wrote:
Do you have a photo? I'm assuming a delrin nut.
-Tim
----- Original Message -----
From: Okla Mike (Liltwisted)
To: legacy-ornamental-mills@googlegroups.com
Sent: Thursday, October 09,
2014 6:54 PM
Subject: Re: New Owner of a
Woodchuck MA - Need documentation
Split nut on the main drive but not on the
carriage
On 10/9/2014 4:08 PM, Tim Krause
wrote:
I've never seen a copy of the Woodchuck manual either.
Am I understanding that the woodchuck does not have a split
nut on any axis?
-Tim
----- Original Message -----
From: Okla Mike (Liltwisted)
To: legacy-ornamental-mills@googlegroups.com
Sent: Thursday, October
09, 2014 6:48 AM
Subject: Re: New Owner
of a Woodchuck MA - Need documentation
I've been looking for that darn thing. I am
sure it is around but can't find it. Will keep looking
Mike
OK
On 10/9/2014 3:02 AM, Bill
Bulkeley wrote:
Hey
Mike I don’t suppose you have the woodchucks
instruction assembly manual do you
I’d
love to see one and I bet James would too
Bill
From: legacy-ornamental-mills@googlegroups.com
[mailto:legacy-ornamental-mills@googlegroups.com]
On Behalf
Of Okla Mike (Liltwisted)
Sent:
Thursday, 9 October 2014 1:36 PM
To:
legacy-ornamental-mills@googlegroups.com
Subject:
Re: New Owner of a Woodchuck MA - Need
documentation
You are correct about
the lead screw nut. It attaches to the bracket
shown below the crank handle in the picture. You
will see two studs on the router mount that will
line up with them. They will be held in place
with 2 wing nuts. When you are in a free Y axis
mode, take off the wingnuts and flip the bracket
away from the router. It will slide free now.
The little shaft in the U bracket is the reversing
bracket. For counter-clockwise or left hand
twists.
Mike
Ok
On
10/8/2014 7:07 PM, James Fadenrecht wrote:
Thanks so much for the
help. I'm sure this will get me started. In
looking at the parts and the machine, I still
don't see how or which part connects the drive
screw to the router base. The only threaded
part that looks like it would connect is the
upper left corner of the second picture. If
this is the correct part, how does it allow
disconnecting from the drive screw when not
used...does it allows have to be reversed to
send it back to the starting point?
--
You received this message because you are subscribed to the Google Groups
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at http://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.
--
You received this message because you are subscribed to the Google Groups
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at http://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.
