The dove tail jigs are shown in picturs from my previous posts on the revo
I don’t have anything on mortis and tenon with the revo i do have this http://legacywoodworking.com/class.cfm?id=58 it shows a mortis it could be done the same on the revo sorry I don’t have your off list email Bill From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Richard Ellis Sent: Saturday, 15 April 2017 6:36 PM To: Legacy Ornamental Mills Subject: Re: Revo Thanks for the you tube I had seen it before , but thanks anyway. One thing that puzzles me is the fact that the jigs used to make the tenons, mortices and dovetails etc are not shown.!!! ??? I always find that the accurate jig making is the hardestthing to do. I can do box joints, and with the table that I made out of 18mm ply enables me to do flat planing, routing reeds flutes etc. I am still a little unsure if it is that much better than the Woodchuck, which as Mike has proved is very adaptable. No doubt I shall buy the Revo but time will tell. I have another question for you --- off Forum Could you email me ---It is about another forum Thanks Richard On Friday, April 14, 2017 at 10:44:17 PM UTC+1, aussiman wrote: The revo can do a great many things don’t underestimate it. https://www.youtube.com/watch?v=bpDJNYqCrEU It is featured a few times in legacys video and all the spindle work on here the revo can do as well Bill From: legacy-orna...@googlegroups.com <javascript:> [mailto:legacy-ornamental-mills@googlegroups.com <javascript:> ] On Behalf Of Richard Ellis Sent: Saturday, 15 April 2017 2:39 AM To: Legacy Ornamental Mills Subject: Re: Revo Thanks for that Bill I have had a three respond to my request for a Revo, will have to wait and see who has the most extras, all seem to be in the south of the U.K. so not too far for me to travel. I am still not sure if the Revo can do more things that I can;t do on my Woodchuck, Got to see one in the flesh, at least it won't take up as much room as my Woodchuck!!! Regards Richard On Friday, April 14, 2017 at 5:13:52 PM UTC+1, aussiman wrote: Here is a list i have of most of the extras i think that were available for the revo back in the day with some of the prices they charged for them. To help you decide what extras you might want for a revo if you buy one . Bill From: legacy-orna...@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Tim Krause Sent: Friday, 14 April 2017 8:51 PM To: legacy-orna...@googlegroups.com Subject: Re: Revo There where two models. I'll have to refer you to the hidden history page again. http://ornamentalmills.com/history/index.html The choice of accessories is really up to you and the work you see yourself doing. Personally I'd get all the gears available to my 900. I'd also get the missing directional gear. I liked the pin router option that can be seen on Legacy's site in the pedestal table. I would also like to have a rotary table. I'd also add an aftermarket 4 jaw chuck. I don't see any value in the dovetail and box joint attachment. They seem a bit crude and do not show elegant craftsmanship. I do value the concept of how a jig like them could be setup. That's my starting point. -Tim ----- Original Message ----- From: Richard Ellis To: Legacy Ornamental Mills Sent: Friday, April 14, 2017 1:43 AM Subject: Revo Hi all you Legacy folk I am looking at buying a Revo, and came across an old post by Bill ---:Saying about extras for the Revo. I was wondering which are the most important extras that would be useful. Bill posted on the 10.5.14 about extras See below Richard If you want to choose pick one with as many extras as possible -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-orna...@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> Virus-free. <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> www.avg.com -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-orna...@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <javascript:> . To post to this group, send email to legacy-orna...@googlegroups.com <javascript:> . Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> Virus-free. <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> www.avg.com -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> Virus-free. <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> www.avg.com -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
