Legacy doesn’t tell us everything and when you open your package and see your order then you got it. stuff for the old mills is getting harder and harder to get. I been waiting years for a ball bearing head stock for my mill I ordered from them. as legacy states they no longer support or supply anything to do with the old mills so any thing you can get from them I feel is a bonus and probably old stock left over from their manual mill days
Bill From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Tim Ziegler Sent: Wednesday, 6 February 2019 1:13 AM To: legacy-ornamental-mills@googlegroups.com Subject: Re: Make a "Split Nut" - & buying parts from Legacy Thanks Bill I am only going by what Cindy shared with me? Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Tue, Feb 5, 2019 at 8:07 AM Bill Bulkeley <bulke...@mmnet.com.au> wrote: Legacy rail has 2 wide grooves and 2 narrow grooves 80-20 has all narrow grooves if there’s a legacy rail there please post a link to it I would love to see it. I believe Legacy had their rails made exclusively for them only and not too the general public so you had to buy only from them then they went cnc and changed rail type to a more common more available one. Bill From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Tim Ziegler Sent: Wednesday, 6 February 2019 12:25 AM To: legacy-ornamental-mills@googlegroups.com Subject: Re: Make a "Split Nut" - & buying parts from Legacy Good morning all, As promised Being fairly new on this I did a lot of digging as I did not want to jump in with out first knowing more about components, and their availability. Even when I went after the predecessor the WC I dug until my head hurt. (Mike Pung and I had many discussions.) Later joining the forum I got to know Curtis George. I had many more discussions with Curtis George. Thanks again for so much support Curt & Mike. So once I found the 1200 LOM and talked to Cindy from LOM, extensively she gave me the company's name of where we can still get rails etc... I'm not exactly sure how to verify the rail style as you mentioned some are different then others. So the company is 80-20 inc. web site is www.80-20inc.com https://8020.net 844-802-0932 phone servi...@80-20inc.com Big boys dream from what I can see. You can even buy it by the foot so in my case I'm going to make the small piece support for running narrow moulding. Hope this helps someone. Kind regards, Tim of ZWWS Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Tue, Feb 5, 2019 at 1:28 AM Bill Bulkeley <bulke...@mmnet.com.au> wrote: I thought the aluminium legacy rails for the manual mills were discontinued being made. On some of the cnc mills the rail is different When looking make sure it’s the rail you want and not something just similar. if it truly is the old legacy rail I’m sure many here would be interested in where it can be purchased. Bill From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Ray Leaman Sent: Tuesday, 5 February 2019 2:44 PM To: legacy-ornamental-mills@googlegroups.com Subject: Re: Make a "Split Nut" - & buying parts from Legacy Thanks much. This is very helpful. If not too much of an imposition l could use your reference on the aluminum rail source. Thanks again for your feedback. Much appreciated! Ray Sent from my iPad On Feb 3, 2019, at 12:12 PM, MWF <mwfos...@earthlink.net> wrote: To all, I, too, agree with Tim. As long as we LOM Owners show Legacy that we need and are willing to buy parts for our LOMs - it increases the likelihood that they will be willing to make parts for our "Legacy" (In this case meaning no longer in production.) Mills. Thanks you Tim for your "Words of Wisdom". Mac _____ _____ -----Original Message----- From: Bill Bulkeley Sent: Feb 3, 2019 4:28 AM To: legacy-ornamental-mills@googlegroups.com Subject: RE: Make a "Split Nut" I agree Tim Bill From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Tim Krause Sent: Sunday, 3 February 2019 8:01 PM To: legacy-ornamental-mills@googlegroups.com Subject: Re: Make a "Split Nut" Joe in NY made a batch of split nut a while back. You all might want to ask for availability second. My first supplier would be Legacy so they will keep making the parts needed for our machines. Tim On Feb 2, 2019, at 8:22 AM, MWF <mwfos...@earthlink.net> wrote: Thank you, Tim. Mac _____ -----Original Message----- From: Tim Ziegler Sent: Feb 2, 2019 8:05 AM To: Legacy Ornamental Mills Subject: Re: Make a "Split Nut" I have a buddy up here in Minnesota that has a CNC and I shot him an email to see if this something he can create. Hopefully I hear something back from him this morning. kind regards, Tim of ZWW&S On Thursday, August 3, 2017 at 11:23:26 AM UTC-5, Va Oak wrote: Hello all, I am not sure how well a split nut made from HDPE will hold up - but here is my 2-cents' worth: HDPE (Look on bottom of plastic jugs, bottles, etc for the Recycle symbol w/the #2) is the only plastic that I know of that we can "re-purpose" at home. Do an Internet/BING search for this - you'll be amazed. I find that the plastic Folgers and Maxwell House coffee canisters are labeled #2 - as are most milk jugs. The two coffee brands yield red and blue plastic respectively. My thought is that you embed a matching Acme rod into the mold you melt the #2 plastic in. Once cooled, you should be able to "unscrew" the rod from the plastic billet. You then cut/machine the billet to the exterior measurements you need and then split it down the center line. "Machining" can be done with your router, bandsaw, etc. Does anyone have an idea of how well the #2 plastic (HDPE) will hold up? Even if it wears down after 6 months of use - you will be able to reuse that worn out piece, with some added #2 plastic, and melt/mold a new piece. If your mold & billet is long enough, you can produce a year's-worth in one mold. If anyone tries this - or something similar, please share pictures and results. Mac _____ _____ -----Original Message----- From: 'joe biunno' via Legacy Ornamental Mills Sent: Aug 3, 2017 10:00 AM To: Legacy Ornamental Mills Subject: Re: Wood Chuck Tour by Mike Pung i'll offer an opinion here, as this could have been a problem for me on my recently acquired 1500...the problem is, due to the action/movement of the lead screw, the threads in the split nut wear sideways, especially when using a drive motor...think of each cross section of thread as a square(see photo)...I measured the cross section of the thread(in a new nut) to be .140" wide...in the photo of the worn nut, that same dimension is down to .065...so you could say the thread went from 1/8" full(new) to 1/16"...and sanding the nut down is not going to improve the function of the nut, in my opinion...maybe early on you can sand the nut to get a bit more life out of it, but that's it...the key to solving this problem is finding the 5/8-4 acme thread tap...once you have the tap, to make a new split nut is somewhat simple...and anyone who has that "hinged" split nut, I would swap that out and set up a sliding split nut...much more problematic to make that hinged split nut...so, if any member knows where to get that tap, here or overseas, please let the group know...I certainly would like to purchase one...barring that, I would also attempt to make a tap from some acme, threaded rod, if I had to...and the casting idea is also an excellent idea...joe b. <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> Virus-free. <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> www.avg.com -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
