Probably didn't say that right Curt. Hope you can figure out what I mean. I'm still working on calling out the right terminology for the elements of a legacy mill.
Ray On Sat, Nov 28, 2020 at 12:06 PM Ray Leaman <[email protected]> wrote: > Sorry Curt but to pick your brain just a bit further...I've seen drive > motors for both the hand crank screws and the headstock via some linkages > to a turntable in some videos. How many motors does one need to eliminate > the most hand cranking as possible. Do you have any pictures of your set > up? > > Thanks > > Ray > > On Sat, Nov 28, 2020 at 12:01 PM Ray Leaman <[email protected]> wrote: > >> Where did you source your motors? >> >> Ray >> >> On Thu, Nov 26, 2020 at 3:38 PM 'Curt George' via Legacy Ornamental Mills >> <[email protected]> wrote: >> >>> Hello Ray >>> >>> Legacy used a direct drive coupler to hook up there motor drive. (a >>> love-joy coupler. ( >>> https://ec.kamandirect.com/storeus/product/L075-HUB-5-8-3-16X3-32-KW/Lovejoy-L-Type-Hubs-with-Keyway-Inch-Imperial-Bore-Bore-Size-0-625/_/R-4235591?matchtype=&network=g&device=c&adposition=&keyword=&gclid=Cj0KCQiAwf39BRCCARIsALXWETzpyqjrro94COWWz5E8PJGOh_ZPKqJ2LG0YNwx0aCw4vkhFBossn5saAlr8EALw_wcB >>> ) >>> >>> I bought my motor separately and its not the same size as what Legacy >>> used. So I went with the chain drive for my set-up. >>> The chain has some disadvantages over the direct drive. mainly in the >>> directional movement. you will find that one way the chain works very well, >>> but on the reverse the chain will tend to slip or skip or the linkage is >>> not 100% on. >>> >>> gota run. >>> >>> have a good day. >>> >>> C.A.G. >>> >>> On Thursday, November 26, 2020, 03:19:39 PM EST, Tim Ziegler < >>> [email protected]> wrote: >>> >>> >>> I took my drive off my WoodChuck and put it on my 1200 works great. >>> >>> Kind Regards, >>> >>> Timothy J. Ziegler >>> Ziegler WoodWork & Specialty >>> 14171 160th Ave. >>> Foreston MN 56330 >>> >>> 320-294-5798 shop >>> 320-630-2243 cell >>> >>> >>> On Thu, Nov 26, 2020 at 1:49 PM Ray Leaman <[email protected]> wrote: >>> >>> I think I recall a post on this site on this subject. >>> >>> I am trying to learn all I can about mechanising a 1200 mill. How would >>> this have to be set up. Pics would be fine but a little description of how >>> it was done would be helpful. >>> >>> Thanks >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "Legacy Ornamental Mills" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCdKeRXnQ9kTj-cJHx7wXyLWJenzVO09PsSUfFoaACYp5Ew%40mail.gmail.com >>> <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCdKeRXnQ9kTj-cJHx7wXyLWJenzVO09PsSUfFoaACYp5Ew%40mail.gmail.com?utm_medium=email&utm_source=footer> >>> . >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "Legacy Ornamental Mills" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLGq0Fs%3DQHZ_dAefsj50QWcj3XzfP-YPJcgiUJ6Hqd6nxg%40mail.gmail.com >>> <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLGq0Fs%3DQHZ_dAefsj50QWcj3XzfP-YPJcgiUJ6Hqd6nxg%40mail.gmail.com?utm_medium=email&utm_source=footer> >>> . >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "Legacy Ornamental Mills" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/legacy-ornamental-mills/1131458537.1177063.1606423084786%40mail.yahoo.com >>> <https://groups.google.com/d/msgid/legacy-ornamental-mills/1131458537.1177063.1606423084786%40mail.yahoo.com?utm_medium=email&utm_source=footer> >>> . >>> >> -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BsRaFEThh31de%3DcxeUz5hgH5M1k87TQ0jkZtoGv1boVw%40mail.gmail.com.
