Thanks Tim. Good to know these ideas work on the 1200 LOM. Very helpful to my understnding some things.
Ray On Mon, Feb 8, 2021 at 11:27 PM Tim Ziegler <[email protected]> wrote: > Hey Ray, > > just a short one as it's getting a bit late and I just got in. > But yes I have a WoodChuck with the dual motor drive. You can run either > together or individually. > So basically it would run like our typical LOM's and if I chose to run > just the headstock spindle with the independent motor. > so Curt and I were talking about me taking my WC head stock motor and > putting it on my 1200 LOM. to run the head stock. > It's basically the same as Bill's set up. > I also just recently picked up another LOM 1500 and have it all together. > little older machine and has the > adjustable slides but does have the direct drive motor on the acme thread > shaft. > A person could really come up with some cool ideas. run the rotary table > and still have full access and control of the gear drive etc... > Hope that was some of what you were looking for. > > Kind Regards, > > Timothy J. Ziegler > Ziegler WoodWork & Specialty > 14171 160th Ave. > Foreston MN 56330 > > 320-294-5798 shop > 320-630-2243 cell > > > On Mon, Feb 8, 2021 at 5:48 PM Ray Leaman <[email protected]> wrote: > >> I am intrigued by your set up Bill. While I'm not sure exactly what can >> be done with the two motor set up, on the surface the variable speeds you >> can achieve are almost endless within the sphere of what an LOM can do in >> my opinion. In going over and over your video I can see the benefit of a >> swing away set up for engaging and changing the various gears. What I >> could not see was how the spindle motor linkage was connected. Do you use >> the same cog wheel for engaging all the legacy gears? Do you have a video >> on how you did all that in a little more detail? >> >> Also where did you source your motors? Did they come off another >> machine (Wood Chuck) or did you acquiree them from a commercial source? >> >> So many questions I know but as you can, maybe you can add a few further >> details. >> >> Finally, in reading some of the responses to your post it seems like your >> set up may greatly facilitate template/copying work? Have you done any of >> that? If so, how did it go process wise. Curt and Tim Z it sounds like >> you guys may have done or at least are aware of how that might work so >> perhaps you could jump in with sharing your experiences ?? >> >> Nice Work Bill!! Thanks for your videos. >> >> >> On Mon, Feb 8, 2021 at 3:32 AM <[email protected]> wrote: >> >>> Well todays job was finishing off the spindle motor on my hybrid legacy >>> >>> Gave it its maiden run worked great, so many speeds can be had from >>> really really slow to quite fast by changing gears from the .25 to the >>> standard to the 2x and all using the variable speed motor which fits them >>> all. That’s the best thing about a swing motor as long as the gears mesh it >>> works even when the bed is fully up or fully down and everywhere in-between. >>> >>> https://youtu.be/n80P9cLYkFs >>> >>> >>> >>> Bill >>> >>> >>> <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> >>> Virus-free. >>> www.avast.com >>> <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> >>> <#m_2884982717580178129_m_7844869206107183113_m_-7190943888803397965_DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2> >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "Legacy Ornamental Mills" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/legacy-ornamental-mills/000101d6fdf4%24df6cb7e0%249e4627a0%24%40mmnet.com.au >>> <https://groups.google.com/d/msgid/legacy-ornamental-mills/000101d6fdf4%24df6cb7e0%249e4627a0%24%40mmnet.com.au?utm_medium=email&utm_source=footer> >>> . >>> >> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> To view this discussion on the web visit >> https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2B0yKnoDiueuy26GkPWFoofDx3FnY6Uo3P8mfAA1%3DhM8g%40mail.gmail.com >> <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2B0yKnoDiueuy26GkPWFoofDx3FnY6Uo3P8mfAA1%3DhM8g%40mail.gmail.com?utm_medium=email&utm_source=footer> >> . >> > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFFCwqakjfq0quceha_URHgT%3DTnFAbMSM6MPq%3DtJYVb%3Dg%40mail.gmail.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFFCwqakjfq0quceha_URHgT%3DTnFAbMSM6MPq%3DtJYVb%3Dg%40mail.gmail.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCdKGHk7sE%2B%3DKEHO3qstCZPok4bE-ut4c3g3gught60gPqg%40mail.gmail.com.
