Sharper cutters and slower rpm helps that too when I do the big 4tpi threads I’m running the router on its slowest speed and a very very slow feed rate
Chipping is a much more of a problem than burning lots of thin ca glue helps too it also might help you on the rosettes as well, paint them with ca just before a last 10 thou finishing cut. If you don’t intend to ever coat your threaded project with anything but an oil before you finish the thread submerge it in a wood oil in a pressure pot over night to saturate the wood with oil it should really help with woods that chip bad but I like a bit of a polish so I don’t do that. Bill From: legacy-ornamental-mills@googlegroups.com <legacy-ornamental-mills@googlegroups.com> On Behalf Of Tim Ziegler Sent: Thursday, 22 April 2021 10:52 PM To: legacy-ornamental-mills@googlegroups.com Subject: Re: milling fine pitches with sprockets and chain Well I sure hope all this info is archived in someone's locker some where. I'd like to see a lot of the past stuff. I also want to start a post about raising and lowering the Z access with either the hand wheel or motor. But effective enough to get out of cut before it burns On Thu, Apr 22, 2021, 7:43 AM <bulke...@mmnet.com.au <mailto:bulke...@mmnet.com.au> > wrote: I changed nothing they just replace the legacy gears on the mill. I posted it on the group many years ago but I searched the archives and could not find the post so what you see is all I have I’m glad I kept it now Tim K made a set too and I couldn’t find his post either sorry Bill From: legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> <legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> > On Behalf Of Tim Ziegler Sent: Thursday, 22 April 2021 8:56 PM To: legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> Subject: Re: milling fine pitches with sprockets and chain I have a dumb question but did you make some of your shafts longer to accomidate those sprokets or is there enough space to accomidate them? Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Wed, Apr 21, 2021 at 11:17 PM <bulke...@mmnet.com.au <mailto:bulke...@mmnet.com.au> > wrote: opps there is a typo in the first one I had the word (gear) instead of (sprocket) written in the attachment fixed now Bill From: legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> <legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> > On Behalf Of bulke...@mmnet.com.au <mailto:bulke...@mmnet.com.au> Sent: Thursday, 22 April 2021 1:52 PM To: legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> Subject: milling fine pitches with sprockets and chain Looking through my legacy stuff on my computer and I found this page of mine on using a chain and sprockets on the mill to cut fine pitches or threads if you use the 60 degree router bit. Now this was for me only so sorry if its not all that clear to follow but I thought I might share, one or 2 of you guys might like it I added a few pics to help. This was pre fire so no more info sorry. Bill -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/000501d7372a%24e550a260%24aff1e720%24%40mmnet.com.au <https://groups.google.com/d/msgid/legacy-ornamental-mills/000501d7372a%24e550a260%24aff1e720%24%40mmnet.com.au?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/000d01d7372e%245b5bb8c0%2412132a40%24%40mmnet.com.au <https://groups.google.com/d/msgid/legacy-ornamental-mills/000d01d7372e%245b5bb8c0%2412132a40%24%40mmnet.com.au?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLHDqQ1wpDyt9s2wTGP6Md%3Duro9DnTE6UKQxQgC72BE0jA%40mail.gmail.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLHDqQ1wpDyt9s2wTGP6Md%3Duro9DnTE6UKQxQgC72BE0jA%40mail.gmail.com?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/002001d73775%241547b040%243fd710c0%24%40mmnet.com.au <https://groups.google.com/d/msgid/legacy-ornamental-mills/002001d73775%241547b040%243fd710c0%24%40mmnet.com.au?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLExvOX6ztBB0rn1e0fVYStw7AzQ9JRufjhv54HUOSeQqw%40mail.gmail.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLExvOX6ztBB0rn1e0fVYStw7AzQ9JRufjhv54HUOSeQqw%40mail.gmail.com?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/003f01d7377b%2403f2fc40%240bd8f4c0%24%40mmnet.com.au.