Curtis, Thanks. (As Bill correctly suggests - I changed Subj line to reflect Paper Scroll Cut/Ribbon Twist.) The article you had attached onto this posting is The Article about Carl Tourigny making the "Paper Scroll Cut". I did note that Phantom Engineering called this cut a "ribbon twist in their side note. If I recall correctly, there is also a "Ribbon Twist" cut - that looks differently than this "paper scroll cut/ribbon twist. But I can't find any photo or drawing of it. Mac -----Original Message----- From: Sent: Feb 6, 2022 1:28 PM To: [email protected] Subject: Re: square spirals Hello Mac. On my first posting on this I added the scroll cut to my posting. If Im not wrong the paper scroll cut is the ribbon twist I posted (I will try again.) There are still a lot of Legacy and Phantom, early articles that Do not have on file. as well as some of there builders (VHS) video series, That I am always on the lookout for. C.A.G.
On Sunday, February 6, 2022, 12:16:21 PM EST, M.W.Foscue wrote: Curtis, Thanks you for digging that one out and sharing it! Towards the end of the article - they mention that the next month's article will feature the "Paper Scroll Cut". Do you happen to have that write-up as well? I;m curious as to what that one looks like. Have a Super Sunday! Mac -----Original Message----- From: Sent: Feb 6, 2022 11:34 AM To: [email protected] Subject: Re: square spirals I took a photo of the paperwork. This might help? C.A.G. On Sunday, February 6, 2022, 11:23:30 AM EST, Curt George wrote: Bill here is the article you were looking for. and the ribbon twist that you can do with your new toy. ;-) Sorry about the quality of the copy's, ONE Day I plan to find the originals and have them copied with a high resolution to make them easer to read. I hope these help? Have a good day. C.A.G. On Sunday, February 6, 2022, 08:26:11 AM EST, Jeff Richmond wrote: Here is the Woodchuck Manual link from the Legacy site. I took a quick browse but I did not see that feature. https://drive.google.com/a/legacywoodworking.com/file/d/1hnAfkrQb_WH_95XoMweOe5UL2XUj0imc/view?usp=drivesdkJeff from Connecticut Sent from my iPhone On Feb 6, 2022, at 3:34 AM, [email protected] wrote: Well first attempt at a square spiral I started out 2inch pitch 2inch bit single start but the mill had other ideas lol it was in fact a 4 start 8 inch pitch go figger lol I almost got it but the angle didn’t want to play ball either I drawed it out on paper mathed it out but the angle wouldn’t be in it either I had to do a trial and error method I got it almost perfect but I had a dig in and I think it moved a few degrees So it doesn’t quite line up. This is defiantly a learning curve square spirals are totally different from making round ones I sure wish I had a woodchuck manual with instructions in it on square spiral making to refer to. The ratio of the pitch to the angle you set the roatry table is a night mare Bill -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group.To unsubscribe from this group and stop receiving emails from it, send an email to [email protected] (mailto:[email protected]).To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/000001d81b34%2411acdb60%2435069220%24%40mmnet.com.au. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group.To unsubscribe from this group and stop receiving emails from it, send an email to [email protected] (mailto:[email protected]).To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/E88891A0-3E63-41FF-80AD-68D8F6834888%40gmail.com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected] (mailto:[email protected]). To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/640144703.216344.1644165261986%40mail.yahoo.com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected] (mailto:[email protected]). To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/e3094025-364f-b82d-99aa-77436cc0be0d%40earthlink.net. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected] (mailto:[email protected]). To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/1524326911.230430.1644172092330%40mail.yahoo.com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/5dc43a46-d75b-867f-9a66-58d7432e0081%40earthlink.net.
