I guess but I think I will just stay with motors lol
Bill From: 'Curt George' via Legacy Ornamental Mills <legacy-ornamental-mills@googlegroups.com> Sent: Thursday, 16 February 2023 12:50 AM To: legacy-ornamental-mills@googlegroups.com Subject: Re: Motor for 1200 Come on Bill, You have to admit it would be better then hand cranking. ;-) C.A.G. On Wednesday, February 15, 2023 at 01:29:37 AM EST, <bulke...@mmnet.com.au <mailto:bulke...@mmnet.com.au> > wrote: Well if the power ever goes out you got that covered curt lol Bill From: 'Curt George' via Legacy Ornamental Mills <legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> > Sent: Wednesday, 15 February 2023 4:28 PM To: legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> Subject: Re: Motor for 1200 When there is a will, there is always a way. DC motors are not cheap most of the time. (if you want to buy them new.) But there are other methods to get the job done besides adding a motor. I have always though that the Legacy could be made to work like an old Barns Lathe. That is peddle powered. You don't need to go fast, the router dose most of the work. A simple flywheel and a pump/crank/or peddle could easily be made to work the Legacy something like these could work. https://www.youtube.com/watch?v=kURUTelZfmI https://www.youtube.com/watch?v=3jkxMGPsjR8 https://www.youtube.com/watch?v=gpAz-xgLynU Just for some ideas, OUT SIDE THE BOX. (so to speak.) ;-) C.A.G. On Tuesday, February 14, 2023 at 10:12:18 PM EST, Tim Ziegler <timjzieg...@gmail.com <mailto:timjzieg...@gmail.com> > wrote: lets see if Bill will put that out there for you. I know you can get almost any gear motor and drive to work if you use sprockets and chain. I did that on my 1200 for the first few years then finally got a mounting bracket made and changed it. Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Tue, Feb 14, 2023 at 9:02 PM Vadim Sidelnikov <vsidelni...@gmail.com <mailto:vsidelni...@gmail.com> > wrote: Could someone recommend a specific motor or type of motor and show some pictures of how it’s wired/attached? I have a 1200. This whole hand cranking thing is getting old fast, and I only just got started. Sent from my iPhone -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills%2bunsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/1B20A9FD-8C5B-4D06-BF66-F7867F3B5B71%40gmail.com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLGc9Ak0bvc6RP8zTCNrW7zq8xXvyXDVyy-m7EqiFwRjJg%40mail.gmail.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLGc9Ak0bvc6RP8zTCNrW7zq8xXvyXDVyy-m7EqiFwRjJg%40mail.gmail.com?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/329230249.1051142.1676438867812%40mail.yahoo.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/329230249.1051142.1676438867812%40mail.yahoo.com?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/002701d94106%24da794490%248f6bcdb0%24%40mmnet.com.au <https://groups.google.com/d/msgid/legacy-ornamental-mills/002701d94106%24da794490%248f6bcdb0%24%40mmnet.com.au?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/487254309.1098627.1676469015134%40mail.yahoo.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/487254309.1098627.1676469015134%40mail.yahoo.com?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/001101d94156%248746b050%2495d410f0%24%40mmnet.com.au.
