Got it. Thanks. -----Original Message----- From: <legacy-ornamental-mills@googlegroups.com> Sent: May 29, 2023 6:51 AM To: <legacy-ornamental-mills@googlegroups.com> Subject: Re: charcuterie board Groove on LOM
Hey Mac, Thanks Its actually Red Alder. The finish is 3 coats of a Food Grade Butcher Block finish. It has mineral oil and a balance of Waxes in it. I'll grab the brand later. Its best applied prewarmed and applied with a soft cotton rag. It still needs to be buffed up a bit, but I had to let it soak in. Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Sun, May 28, 2023 at 9:53 PM M.W.Foscue <mwfos...@earthlink.net (mailto:mwfos...@earthlink.net)> wrote: Tim, Very nice! Your " finished result was good" needs revision: Should be "finished result was Excellent!"What is the wood you made it from? Cedar? Hemlock? Cyprus? And what finish did you apply? (brand & specifics - like Walrus Oil applied w/a cloth; or used a 3M-type Scotchbright pad; etc.) Thanks for sharing. Mac -----Original Message----- From: <legacy-ornamental-mills@googlegroups.com (mailto:legacy-ornamental-mills@googlegroups.com)> Sent: May 28, 2023 2:55 PM To: LOM Group <legacy-ornamental-mills@googlegroups.com (mailto:legacy-ornamental-mills@googlegroups.com)>, Tim Ziegler <timjzieg...@gmail.com (mailto:timjzieg...@gmail.com)> Subject: charcuterie board Groove on LOM Found a good use of my LOM this week on a job and it worked extremely well. used 2 Rockler hold downs and to LOM mounting hubs to hold it in place. Mounted my stops on the rails to control my length of the groove. I manually controlled the Router and Carriage to minimize burning. As you can see the finished result was good. Kind Regards,Timothy J. Ziegler -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com (mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com). To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/968e634f-fed6-1996-2c8e-5cf70f136d19%40earthlink.net. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com (mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com). To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLGZEk__HRCQ5efRxALLHunYALVKgKMEg8LS4n-_eo5meQ%40mail.gmail.com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/910a9476-355c-b9e1-a58d-91e400eb1c66%40earthlink.net.