All sounds good Dan. Kind Regards,
Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Mon, Jul 17, 2023 at 8:44 AM cdkr...@gmail.com <cdkra...@gmail.com> wrote: > Re: relaxed twist. I used my rearranged gear train to index the two > starts so that the cutter diameter and work piece diameter are independent > and accurately repeatable from piece to piece. The work pieces could be > remounted for additional cuts if that were intended. > > I'm also going to rework the stock tail center so that the clamp > compresses a piston against a stiff spring housed inside the shaft. I found > that slight variations in length of work piece caused both the tail stock > frame and the head stock frame to distort as much as 1/8" unless I relieved > the tension by repositioning the frame. I'm expecting the stiff spring to > absorb this distorting pressure thus allowing for quicker and more > consistent work piece changes. The intent is to make a consistent starting > point "absolute" within the limits of the frame strength. It may come to > the point my metal working OCD for precision leads to a rework of the > center holding frames at both ends, or at least a reinforcement. > DanK > > On Monday, July 17, 2023 at 9:31:28 AM UTC-4 cdkr...@gmail.com wrote: > >> Thank you, guys. The most gratifying reward is granddaughter liked them >> and will use them in her first apartment. >> DanK >> >> On Sunday, July 16, 2023 at 10:00:20 PM UTC-4 Jeff Richmond wrote: >> >>> Nice work 👍 >>> >>> Jeff from Connecticut >>> Sent from my iPhone >>> >>> On Jul 16, 2023, at 6:53 PM, cdkr...@gmail.com <cdkr...@gmail.com> >>> wrote: >>> >>> >>> >>> These were delivered this weekend. Old growth American black walnut. >>> Drilled 4" deep for stemmed flowers and tapered for standard candle. >>> Test tubes for water holding were late, so will be shipped later. >>> They look especially sharp with the classy glass bobeches in place >>> mimicking the saucer base. Can be seen in western Iowa. >>> >>> <ElizabethCandlesticks.JPG> >>> >>> DanK >>> On Friday, July 7, 2023 at 2:23:33 PM UTC-4 Tim Ziegler wrote: >>> >>>> Hey Dan, >>>> >>>> Excited your working on a project again for sure. >>>> Your Pic did not show up. >>>> Are you using the single or double gear set between your drive gear and >>>> duplex? >>>> >>>> Kind Regards, >>>> >>>> Timothy J. Ziegler >>>> Ziegler WoodWork & Specialty >>>> 14171 160th Ave. >>>> Foreston MN 56330 >>>> >>>> 320-294-5798 <(320)%20294-5798> shop >>>> 320-630-2243 <(320)%20630-2243> cell >>>> >>>> >>>> On Fri, Jul 7, 2023 at 10:34 AM cdkr...@gmail.com <cdkr...@gmail.com> >>>> wrote: >>>> >>>>> Here is a prototype candlestick for a set of four matching for my >>>>> granddaughter. This is red oak, but the gift set will be American black >>>>> walnut. There will be a "saucer" with a carved handle at the edge, you >>>>> know, the old fashioned ring type. That will give it "stability" both >>>>> physically and visually. My original intent was that in addition to the >>>>> standard 7/8" tapered socket, I would drill out for a test tube to allow a >>>>> couple of flower stems to be inserted instead of a candle. But I'm having >>>>> trouble finding a tube of 1/2" OD. It's a set of four because she wanted >>>>> two left twists and two right twists. She has a rope candle mold that is >>>>> right twist, and this would allow her decorating options. >>>>> >>>>> Is this a left hand twist? >>>>> >>>>> >>>>> DanK >>>>> >>>>> -- >>>>> You received this message because you are subscribed to the Google >>>>> Groups "Legacy Ornamental Mills" group. >>>>> To unsubscribe from this group and stop receiving emails from it, send >>>>> an email to legacy-ornamental...@googlegroups.com. >>>>> To view this discussion on the web visit >>>>> https://groups.google.com/d/msgid/legacy-ornamental-mills/585cda5c-93f0-4328-b2d5-5f9696b4e901n%40googlegroups.com >>>>> <https://groups.google.com/d/msgid/legacy-ornamental-mills/585cda5c-93f0-4328-b2d5-5f9696b4e901n%40googlegroups.com?utm_medium=email&utm_source=footer> >>>>> . >>>>> >>>> -- >>> You received this message because you are subscribed to the Google >>> Groups "Legacy Ornamental Mills" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to legacy-ornamental...@googlegroups.com. >>> >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/legacy-ornamental-mills/92b1afa9-a5bf-403a-8157-01467e18228an%40googlegroups.com >>> <https://groups.google.com/d/msgid/legacy-ornamental-mills/92b1afa9-a5bf-403a-8157-01467e18228an%40googlegroups.com?utm_medium=email&utm_source=footer> >>> . >>> <ElizabethCandlesticks.JPG> >>> >>> -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/f405c8b1-9e5d-4202-95bc-c3add9fa9d06n%40googlegroups.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/f405c8b1-9e5d-4202-95bc-c3add9fa9d06n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLH6uuVy5i%3DWRCS7wfDyLucP_iMhzVBepNzYbzOX5-mcqQ%40mail.gmail.com.
