Wow I am so impressed Dan. Great job. Those look absolutely beautiful Very Clean cuts too.
Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty Ziegler Laser Worx LLC 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Fri, Oct 27, 2023 at 10:32 AM cdkr...@gmail.com <cdkra...@gmail.com> wrote: > Finished the cross hatch. Look at how sharp and crisp the > diamonds are. This raw off the LOM, no hand touch up. > The change in spacing is barely detectable from large to small > end of this 2 3/4" stretch. > [image: Capture.JPG] > DanK > > On Thursday, October 26, 2023 at 11:05:41 PM UTC-4 Tim Ziegler wrote: > >> Very Good Dan. It's great to see a plan coming together. >> >> >> >> >> Kind Regards, >> >> Timothy J. Ziegler >> Ziegler WoodWork & Specialty >> Ziegler Laser Worx LLC >> 14171 160th Ave. >> Foreston MN 56330 >> >> 320-294-5798 <(320)%20294-5798> shop >> 320-630-2243 <(320)%20630-2243> cell >> >> On Thu, Oct 26, 2023 at 4:56 PM cdkr...@gmail.com <cdkr...@gmail.com> >> wrote: >> >>> Here's the work so far. The taper is just a hair over 2° and I wondered >>> how much that would affect the spacing at the small end. I probably >>> won't see it until touching up. You can see the tilt of the spindle >>> rails >>> that put the cutting surface parallel to the main frame. I'm going to >>> try one with a slightly increased taper and let the checkering fade >>> into nothingness >>> [image: Capture.JPG] >>> >>> And the chart update. >>> DanK >>> On Thursday, October 26, 2023 at 5:27:07 PM UTC-4 cdkr...@gmail.com >>> wrote: >>> >>>> Today I was motivated to checker an apple piece that I tapered in a >>>> typical handle fashion. So using the Taper Chart sheet from the now named >>>> "LegacyCharts_V10.4" I found that the upper limit to the REVO settings for >>>> taper is 3/8", i.e. the spindle rails won't go clear up to the main frame >>>> rails. So I altered the chart to give a warning about values that can't be >>>> used. And while I was versioning, I decided that the name should be >>>> adjusted to better reflect content. >>>> [image: Capture.JPG] >>>> >>>> These are the settings I went with and was anxious about accuracy of >>>> the taper calcs. They're dead on! >>>> [image: Capture.JPG] >>>> >>>> This is what it looks like to set up. Needs pretty precise measuring. >>>> [image: Capture.JPG] >>>> >>>> My picture of the work got corrupted in transfer, so after supper. >>>> DanK >>>> >>> -- >>> >> You received this message because you are subscribed to the Google Groups >>> "Legacy Ornamental Mills" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to legacy-ornamental...@googlegroups.com. >>> >> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/legacy-ornamental-mills/2a5bb155-7e66-4cfd-b665-99db712ac7c5n%40googlegroups.com >>> <https://groups.google.com/d/msgid/legacy-ornamental-mills/2a5bb155-7e66-4cfd-b665-99db712ac7c5n%40googlegroups.com?utm_medium=email&utm_source=footer> >>> . >>> >> -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/48baf97a-adde-42da-897f-be3e8a68d40dn%40googlegroups.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/48baf97a-adde-42da-897f-be3e8a68d40dn%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLHkZ7_D9SwKibvZRstJZ9ON901nEQPtyC85HuQvosMqgA%40mail.gmail.com.
