Cathy and Rob, many tks for help. Unfortunately Rob they didn't stay open once the programme had been closed down.
Cathy, I did delete whatever column it was this time. In the index view it seemed to always be the second column but I haven't used the descendant's view enough to figure it out, although it wasn't the second one but a different column. Deleting the offending column and then putting it back in SEEMS to have done the trick. I have opened and closed Legacy a few times and they have stayed as they should. I couldn't get the mouse in there to pull it to the right without taking a very long time and a lot of patience and steadiness which I don't have - steadiness that is; patience I have! Here's hoping and thks. I have put up with it for sooooo long!! June ----- Original Message ----- From: "Rob Weiss" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Sunday, October 24, 2004 6:20 PM Subject: Re: [LegacyUG] narrow column problem > June, > Once you've fixed the widths as Cathy suggests, they should stay as you set > them. > Rob > > ----- Original Message ----- > From: "Cathy" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Sunday, October 24, 2004 5:56 PM > Subject: Re: [LegacyUG] narrow column problem > > > > Hi June, > > If you can't get the mouse to pull the column wider you may be best to > > work out what column it is and in Index View - Options > Customise Columns > > delete that particular column. Then you could re add it if desired. > > > > I tried narrowing a column until it disappeared and found I could pull it > > wider again by moving mouse to the right. > > > > Resetting to defaults may be another way to handle this. > > > > Hope that helps, > > Cathy > > > > At 05:49 PM 23/10/2004, you wrote: > >>Hi > >>I have not seen this mentioned so am wondering am I the only one with this > >>particular trouble. On both the index view and the descendent view, when > >>opened, there is always one column which is closed up (abt 1mm apart). > >>Needless to say no information can be seen and it is VERY difficult to get > >>the vertical 'bar' on the double headed arrow in there to open it up. > >> > >>It has been like it for so long that I can't remember when I first noticed > >>it but as I don't use those views much I haven't got around to ask about > >>it > >>before. Any help? > >> > >>June McDonald > >>Canberra, the nation's capital > > > > Legacy User Group Etiquette guidelines can be found at: > > http://www.LegacyFamilyTree.com/Etiquette.asp > > > > To find past messages, please go to our searchable archives at: > > http://www.mail-archive.com/legacyusergroup%40mail.millenniacorp.com/ > > > > To unsubscribe please visit: > > http://www.legacyfamilytree.com/LegacyLists.asp > > Legacy User Group Etiquette guidelines can be found at: > http://www.LegacyFamilyTree.com/Etiquette.asp > > To find past messages, please go to our searchable archives at: > http://www.mail-archive.com/legacyusergroup%40mail.millenniacorp.com/ > > To unsubscribe please visit: > http://www.legacyfamilytree.com/LegacyLists.asp > > > -- > This message has been scanned for viruses and > dangerous content by CyberOne E-Mail Spam and > Virus Protection Service, and is believed to > be clean from viruses. CyberOne accepts no > responsibility for the content of messages > in transit through our servers. > -- > Suspected unsolicited commercial bulk messages > (SPAM) have been marked with {Spam?} tag in > the subject line enabling you to filter them out > by using your mail software's filtering capabilities. > --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.775 / Virus Database: 522 - Release Date: 8/10/04 Legacy User Group Etiquette guidelines can be found at: http://www.LegacyFamilyTree.com/Etiquette.asp To find past messages, please go to our searchable archives at: http://www.mail-archive.com/legacyusergroup%40mail.millenniacorp.com/ To unsubscribe please visit: http://www.legacyfamilytree.com/LegacyLists.asp
