On 05/25/2011 07:55 PM, Somebody in the thread at some point said:
On 05/25/2011 07:28 PM, Somebody in the thread at some point said:
Hi -
Booted on panda
Ethernet, USB etc. seem to work fine, but not thoroughly tested.
I observe this outstanding bug:
https://bugs.launchpad.net/ubuntu/+source/linux-ti-omap4/+bug/781318
Just appears when it's changing modes or blanking the display, it
doesn't seem to indicate anything else or occur any other times.
I also have no red in my display output, but that may well be a board
issue -- I'm not sure if I've ever plugged a display into this board
before.
It would be interesting if anyone else gets this problem.
No problems with colour here.
There's no ext4 support enabled in omap4_defconfig and I only got HDMI
at 640x480.
omap2plus_defconfig doesn't build, I have a patch for the general issue
but I see HDMI audio is also broken for build there so looking at that
first.
Hacking around the HDMI audio build problem, omap2plus_defconfig blows
SIGILL all over my rootfs, that's a new one on me.
omap4_defconfig is workable
- WLAN is good
- eth0 is good
- 640 x 480 on HDMI only
- HDMI audio acting correct but not sound (guess this is simply
fallout from 640x480)
There's a couple of patches on top of linux-linaro-2.6.38 here that fix
the build problem on omap2plus_defconfig and enable ext4 on omap4_defconfig
git://git.linaro.org/people/andygreen/kernel-tilt.git
linux-linaro-2.6.38-buildfixes
Here's the 640x480 dmesg FWIW
[ 0.000000] Linux version
2.6.38-panda_linux-linaro-2.6.38-master-00002-g4d6518c-dirty
(agr...@otae.warmcat.com) (gcc version 4.5.1 20101112 (Red Hat 4.5.1-5)
(GCC) ) #5 SMP Wed May 25 20:16:32 BST 2011
[ 0.000000] CPU: ARMv7 Processor [411fc092] revision 2 (ARMv7),
cr=10c5387f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing
instruction cache
[ 0.000000] Machine: OMAP4 Panda board
[ 0.000000] Reserving 33554432 bytes SDRAM for VRAM
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] OMAP_TAP_DIE_ID_0: 0x01000000
[ 0.000000] OMAP_TAP_DIE_ID_1: 0x0612d687
[ 0.000000] OMAP_TAP_DIE_ID_2: 0x00000001
[ 0.000000] OMAP_TAP_DIE_ID_3: 0x1d620003
[ 0.000000] OMAP4430 ES2.1
[ 0.000000] SRAM: Mapped pa 0x40300000 to va 0xfe400000 size: 0xe000
[ 0.000000] On node 0 totalpages: 110336
[ 0.000000] free_area_init_node: node 0, pgdat c076b020, node_mem_map
c0ccd000
[ 0.000000] Normal zone: 926 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 109410 pages, LIFO batch:31
[ 0.000000] powerdomain: waited too long for powerdomain dss_pwrdm to
complete transition
[ 0.000000] PERCPU: Embedded 8 pages/cpu @c1075000 s10336 r8192
d14240 u32768
[ 0.000000] pcpu-alloc: s10336 r8192 d14240 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 109410
[ 0.000000] Kernel command line: console=tty0 console=ttyO2,115200n8
earlycon=ttyO2,115200n8 earlyprintk=1
root=UUID=3f5789f6-fdb2-43cb-abe8-5e064f387200 rootwait ro fixrtc
nocompcache vram=32M omapfb.vram=0:24M mem=463M ip=none omapfb.debug=1
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.000000] Memory: 430MB 1MB = 431MB total
[ 0.000000] Memory: 420120k/420120k available, 53992k reserved, 0K
highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0xdd000000 - 0xf8000000 ( 432 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdcf00000 ( 463 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0047000 ( 252 kB)
[ 0.000000] .text : 0xc0047000 - 0xc06fae90 (6864 kB)
[ 0.000000] .data : 0xc06fc000 - 0xc076d3b8 ( 453 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] NR_IRQS:410
[ 0.000000] omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for
dpll_mpu_m2_ck.
[ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps
every 131071999ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled
[ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat,
Inc., Ingo Molnar
[ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000000] ... MAX_LOCK_DEPTH: 48
[ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
[ 0.000000] ... CLASSHASH_SIZE: 4096
[ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.000000] ... CHAINHASH_SIZE: 16384
[ 0.000000] memory used by lock dependency info: 3695 kB
[ 0.000000] per task-struct memory footprint: 1152 bytes
[ 0.001129] Calibrating delay loop... 2009.29 BogoMIPS (lpj=7847936)
[ 0.171905] pid_max: default: 32768 minimum: 301
[ 0.172546] Security Framework initialized
[ 0.172912] Mount-cache hash table entries: 512
[ 0.176391] CPU: Testing write buffer coherency: ok
[ 0.177215] Calibrating local timer... 491.91MHz.
[ 0.218963] L310 cache controller enabled
[ 0.218994] l2x0: 16 ways, CACHE_ID 0x410000c4, AUX_CTRL 0x7e470000,
Cache size: 1048576 B
[ 0.221313] CPU1: Booted secondary processor
[ 0.221343] CPU1: Unknown IPI message 0x1
[ 0.402038] Brought up 2 CPUs
[ 0.402069] SMP: Total of 2 processors activated (3972.37 BogoMIPS).
[ 0.403228] devtmpfs: initialized
[ 0.409729] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
emif_fw
[ 0.409759] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l3_instr
[ 0.409790] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l3_main_1
[ 0.409790] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l3_main_2
[ 0.409820] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l4_abe
[ 0.409851] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l4_cfg
[ 0.409851] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l4_per
[ 0.409881] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l4_wkup
[ 0.409881] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
mpu_private
[ 0.409912] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for dsp
[ 0.409942] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for ipu
[ 0.410217] omap_hwmod: l3_div_ck: missing clockdomain for l3_div_ck.
[ 0.415649] print_constraints: dummy:
[ 0.416351] NET: Registered protocol family 16
[ 0.416931] GPMC revision 6.0
[ 0.420257] omap_device: omap_gpio.0: new worst case activate latency
0: 61035
[ 0.420593] OMAP GPIO hardware version 0.1
[ 0.420837] OMAP GPIO hardware version 0.1
[ 0.421051] OMAP GPIO hardware version 0.1
[ 0.421234] OMAP GPIO hardware version 0.1
[ 0.421447] OMAP GPIO hardware version 0.1
[ 0.421661] OMAP GPIO hardware version 0.1
[ 0.427490] omap_mux_init: Add partition: #1: core, flags: 2
[ 0.428894] omap_mux_init: Add partition: #2: wkup, flags: 2
[ 0.432342] omap_device: omap_uart.1: new worst case deactivate
latency 0: 30517
[ 0.438964] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[ 0.438995] hw-breakpoint: 1 breakpoint(s) reserved for watchpoint
single-step.
[ 0.439025] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.445922] pm_dbg_init: only OMAP3 supported
[ 0.446502] OMAP DMA hardware revision 0.0
[ 0.480743] bio: create slab <bio-0> at 0
[ 0.482543] print_constraints: vwl1271: 1800 mV
[ 0.484985] SCSI subsystem initialized
[ 0.486450] omap_device: omap2_mcspi.2: new worst case deactivate
latency 0: 30517
[ 0.489410] usbcore: registered new interface driver usbfs
[ 0.489868] usbcore: registered new interface driver hub
[ 0.490173] usbcore: registered new device driver usb
[ 0.501098] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 400 kHz
[ 0.525024] Skipping twl internal clock init and using bootloader
value (unknown osc rate)
[ 0.525970] twl6030: PIH (irq 39) chaining IRQs 368..387
[ 0.540283] print_constraints: VUSB: 3300 mV normal standby
[ 0.760711] twl6030_usb twl6030_usb: Initialized TWL6030 USB module
[ 0.761749] print_constraints: VMMC: 1200 <--> 3000 mV at 3000 mV
normal standby
[ 0.762939] print_constraints: VPP: 1800 <--> 2500 mV at 1900 mV
normal standby
[ 0.764007] print_constraints: VANA: 2100 mV normal standby
[ 0.764984] print_constraints: VCXIO: 1800 mV normal standby
[ 0.766021] print_constraints: VDAC: 1800 mV normal standby
[ 0.767211] print_constraints: VAUX2_6030: 1200 <--> 2800 mV at 1800
mV normal standby
[ 0.768463] print_constraints: VAUX3_6030: 1000 <--> 3000 mV at 1200
mV normal standby
[ 0.769561] print_constraints: CLK32KG:
[ 0.769897] omap_device: omap_i2c.1: new worst case deactivate
latency 0: 30517
[ 0.782867] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 400 kHz
[ 0.798095] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz
[ 0.798889] omap_device: omap_i2c.4: new worst case activate latency
0: 30517
[ 0.813354] omap_i2c omap_i2c.4: bus 4 rev2.4.0 at 400 kHz
[ 0.815307] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.817291] Bluetooth: Core ver 2.15
[ 0.817504] NET: Registered protocol family 31
[ 0.817535] Bluetooth: HCI device and connection manager initialized
[ 0.817626] Bluetooth: HCI socket layer initialized
[ 0.819702] cfg80211: Calling CRDA to update world regulatory domain
[ 0.821197] Switching to clocksource 32k_counter
[ 0.823455] Switched to NOHz mode on CPU #1
[ 0.828552] Switched to NOHz mode on CPU #0
[ 0.878936] musb-hdrc: version 6.0, musb-dma, otg (peripheral+host),
debug=0
[ 0.879180] omap_device: musb-omap2430.-1: new worst case activate
latency 0: 30517
[ 0.879333] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk
combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[ 0.879364] musb-hdrc: MHDRC RTL version 2.0
[ 0.879364] musb-hdrc: setup fifo_mode 4
[ 0.879364] musb-hdrc: 28/31 max ep, 16384/16384 memory
[ 0.879730] musb-hdrc musb-hdrc: USB OTG mode controller at fc0ab000
using DMA, IRQ 124
[ 0.880279] omap_device: musb-omap2430.-1: new worst case deactivate
latency 0: 61035
[ 0.880615] NET: Registered protocol family 2
[ 0.880950] IP route cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.881988] TCP established hash table entries: 16384 (order: 5,
131072 bytes)
[ 0.882385] TCP bind hash table entries: 16384 (order: 7, 589824 bytes)
[ 0.886688] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.886810] TCP reno registered
[ 0.886840] UDP hash table entries: 256 (order: 2, 20480 bytes)
[ 0.886993] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[ 0.887695] NET: Registered protocol family 1
[ 0.888427] RPC: Registered udp transport module.
[ 0.888458] RPC: Registered tcp transport module.
[ 0.888458] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.888946] Trying to unpack rootfs image as initramfs...
[ 1.131317] Freeing initrd memory: 3904K
[ 1.131378] NetWinder Floating Point Emulator V0.97 (double precision)
[ 1.132507] omap_init_opp_table: no hwmod or odev for iva, [6] cannot
add OPPs.
[ 1.134674] LTTng will clear ccnt top bit every 136 jiffies.
[ 1.243011] VFS: Disk quotas dquot_6.5.2
[ 1.243225] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.245025] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat,
Inc.
[ 1.245544] msgmni has been set to 828
[ 1.247955] io scheduler noop registered
[ 1.247955] io scheduler deadline registered
[ 1.248046] io scheduler cfq registered (default)
[ 1.313659] OMAP DSS rev 4.0
[ 1.479034] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.696960] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a
OMAP UART0
[ 1.743377] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a
OMAP UART1
[ 1.782470] omap_uart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a
OMAP UART2
[ 2.750915] console [ttyO2] enabled
[ 2.805847] omap_uart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a
OMAP UART3
[ 2.884460] brd: module loaded
[ 2.895599] loop: module loaded
[ 2.901794] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 2.908599] omap2-nand driver initializing
[ 2.913208] OneNAND driver initializing
[ 2.920501] usbcore: registered new interface driver asix
[ 2.926391] usbcore: registered new interface driver cdc_ether
[ 2.932769] usbcore: registered new interface driver smsc95xx
[ 2.938995] usbcore: registered new interface driver net1080
[ 2.945129] usbcore: registered new interface driver cdc_subset
[ 2.951568] usbcore: registered new interface driver zaurus
[ 2.957427] cdc_ncm: 7-Feb-2011
[ 2.960937] usbcore: registered new interface driver cdc_ncm
[ 2.967926] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.975067] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 2.983337] ehci-omap ehci-omap.0: new USB bus registered, assigned
bus number 1
[ 3.017120] ehci-omap ehci-omap.0: irq 109, io mem 0x4a064c00
[ 3.032440] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 3.038879] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.046020] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 3.053558] usb usb1: Product: OMAP-EHCI Host Controller
[ 3.059143] usb usb1: Manufacturer: Linux
2.6.38-panda_linux-linaro-2.6.38-master-00002-g4d6518c-dirty ehci_hcd
[ 3.069702] usb usb1: SerialNumber: ehci-omap.0
[ 3.077270] hub 1-0:1.0: USB hub found
[ 3.081329] hub 1-0:1.0: 3 ports detected
[ 3.118530] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.125152] ohci-omap3 ohci-omap3.0: OMAP3 OHCI Host Controller
[ 3.131958] ohci-omap3 ohci-omap3.0: new USB bus registered, assigned
bus number 2
[ 3.173065] ohci-omap3 ohci-omap3.0: irq 108, io mem 0x4a064800
[ 3.255249] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.262390] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 3.269958] usb usb2: Product: OMAP3 OHCI Host Controller
[ 3.275604] usb usb2: Manufacturer: Linux
2.6.38-panda_linux-linaro-2.6.38-master-00002-g4d6518c-dirty ohci_hcd
[ 3.286163] usb usb2: SerialNumber: ohci-omap3.0
[ 3.292541] hub 2-0:1.0: USB hub found
[ 3.296478] hub 2-0:1.0: 3 ports detected
[ 3.302368] usbcore: registered new interface driver cdc_wdm
[ 3.308319] Initializing USB Mass Storage driver...
[ 3.313751] usbcore: registered new interface driver usb-storage
[ 3.320007] USB Mass Storage support registered.
[ 3.325469] usbcore: registered new interface driver libusual
[ 3.415252] usb 1-1: new high speed USB device number 2 using ehci-omap
[ 3.986053] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[ 3.993041] usb 1-1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 4.002288] hub 1-1:1.0: USB hub found
[ 4.006408] hub 1-1:1.0: 5 ports detected
[ 4.088195] usbcore: registered new interface driver usbtest
[ 4.095184] mousedev: PS/2 mouse device common for all mice
[ 4.104431] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[ 4.110900] omap_device: omap_i2c.1: new worst case activate latency
0: 61035
[ 4.120239] i2c /dev entries driver
[ 4.127319] lirc_dev: IR Remote Control driver registered, major 251
[ 4.134155] IR NEC protocol handler initialized
[ 4.138885] IR RC5(x) protocol handler initialized
[ 4.143920] IR RC6 protocol handler initialized
[ 4.148651] IR JVC protocol handler initialized
[ 4.153533] IR Sony protocol handler initialized
[ 4.158386] IR RC5 (streamzap) protocol handler initialized
[ 4.164184] IR LIRC bridge handler initialized
[ 4.168853] Linux video capture interface: v2.00
[ 4.174163] Driver for 1-wire Dallas network protocol.
[ 4.181610] OMAP Watchdog Timer Rev 0x00: initial timeout 60 sec
[ 4.188446] Bluetooth: HCI UART driver ver 2.2
[ 4.193145] Bluetooth: HCI H4 protocol initialized
[ 4.198150] Bluetooth: HCI BCSP protocol initialized
[ 4.203338] Bluetooth: HCILL protocol initialized
[ 4.209228] cpuidle: using governor ladder
[ 4.213623] cpuidle: using governor menu
[ 4.221130] _regulator_get: omap_hsmmc.0 supply vmmc_aux not found,
using dummy regulator
[ 4.231506] _regulator_get: omap_hsmmc.4 supply vmmc_aux not found,
using dummy regulator
[ 4.242187] usbcore: registered new interface driver usbhid
[ 4.248077] usbhid: USB HID core driver
[ 4.255126] OMAP4 HDMI audio SoC init
[ 4.260894] asoc: omap4-hdmi-audio-codec <-> hdmi-audio-dai mapping ok
[ 4.270111] ALSA device list:
[ 4.273223] #0: PandaHDMI
[ 4.276184] oprofile: hardware counters not available
[ 4.281463] oprofile: using timer interrupt.
[ 4.286285] TCP cubic registered
[ 4.289672] Initializing XFRM netlink socket
[ 4.294219] NET: Registered protocol family 17
[ 4.298919] NET: Registered protocol family 15
[ 4.303741] Bluetooth: L2CAP ver 2.15
[ 4.307586] Bluetooth: L2CAP socket layer initialized
[ 4.312896] Bluetooth: SCO (Voice Link) ver 0.6
[ 4.317657] Bluetooth: SCO socket layer initialized
[ 4.322937] Bluetooth: RFCOMM TTY layer initialized
[ 4.328063] Bluetooth: RFCOMM socket layer initialized
[ 4.333465] Bluetooth: RFCOMM ver 1.11
[ 4.337402] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 4.342956] Bluetooth: BNEP filters: protocol multicast
[ 4.344360] mmc0: host does not support reading read-only switch.
assuming write-enable.
[ 4.356842] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 4.360565] mmc0: new high speed SDHC card at address d555
[ 4.362121] mmcblk0: mmc0:d555 SU08G 7.60 GiB
[ 4.365478] mmcblk0: p1 p2
[ 4.376983] lib80211: common routines for IEEE802.11 drivers
[ 4.382965] lib80211_crypt: registered algorithm 'NULL'
[ 4.382965] Registering the dns_resolver key type
[ 4.388275] VFP support v0.3: implementor 41 architecture 3 part 30
variant 9 rev 1
[ 4.396759] ThumbEE CPU extension supported.
[ 4.401367] Registering SWP/SWPB emulation handler
[ 4.411956] usb 1-1.1: new high speed USB device number 3 using ehci-omap
[ 4.419708] omap2_set_init_voltage: Invalid parameters!
[ 4.425201] omap2_set_init_voltage: Unable to put vdd_iva to its init
voltage
[ 4.425201]
[ 4.435729] Power Management for TI OMAP4.
[ 4.440185] sr_init: No PMIC hook to init smartreflex
[ 4.445648] smartreflex smartreflex.0: omap_sr_probe: SmartReflex
driver initialized
[ 4.454040] smartreflex smartreflex.1: omap_sr_probe: SmartReflex
driver initialized
[ 4.462402] smartreflex smartreflex.2: omap_sr_probe: SmartReflex
driver initialized
[ 4.470947] SmartReflex Class3 initialized
[ 4.491516] mmc1: card claims to support voltages below the defined
range. These will be ignored.
[ 4.521423] Synthetic TSC timer will fire each 68 jiffies.
[ 4.521881] OMAPFB: omapfb_init
[ 4.522064] OMAPFB: omapfb_probe
[ 4.522125] OMAPFB: create 2 framebuffers
[ 4.522125] OMAPFB: fb_infos allocated
[ 4.522125] OMAPFB: allocating 25165824 bytes for fb 0
[ 4.534393] mmc1: queuing unknown CIS tuple 0x91 (3 bytes)
[ 4.541870] mmc1: new SDIO card at address 0001
[ 4.587188] usb 1-1.1: New USB device found, idVendor=0424,
idProduct=ec00
[ 4.594360] usb 1-1.1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 4.605529] smsc95xx v1.0.4
[ 4.775878] OMAPFB: allocated VRAM paddr 9ae00000, vaddr de000000
[ 4.775878] OMAPFB: region0 phys 9ae00000 virt de000000 size=25165824
[ 4.775878] OMAPFB: region1 phys 00000000 virt (null) size=0
[ 4.775909] OMAPFB: fbmems allocated
[ 4.776062] OMAPFB: check_fb_var 0
[ 4.776092] OMAPFB: max frame size 25165824, line size 2560
[ 4.776092] OMAPFB: xres = 640, yres = 480, vxres = 640, vyres = 480
[ 4.776184] OMAPFB: set_fb_fix
[ 4.776306] OMAPFB: fb_infos initialized
[ 4.778076] OMAPFB: set_par(0)
[ 4.778106] OMAPFB: set_fb_fix
[ 4.778106] OMAPFB: apply_changes, fb 0, ovl 0
[ 4.778137] OMAPFB: setup_overlay 0, posx 0, posy 0, outw 640, outh 480
[ 4.778137] OMAPFB: paddr 9ae00000, vaddr de000000
[ 4.778411] OMAPFB: pan_display(0)
[ 4.778411] OMAPFB: setcmap
[ 4.778442] OMAPFB: setcmap
[ 4.782348] Console: switching to colour frame buffer device 80x30
[ 4.782440] OMAPFB: pan_display(0)
[ 4.782440] OMAPFB: setcmap
[ 4.786071] OMAPFB: setcmap
[ 4.795684] OMAPFB: framebuffers registered
[ 4.795715] OMAPFB: apply_changes, fb 0, ovl 0
[ 4.795715] OMAPFB: setup_overlay 0, posx 0, posy 0, outw 640, outh 480
[ 4.795715] OMAPFB: paddr 9ae00000, vaddr de000000
[ 4.795745] OMAPFB: apply_changes, fb 1, ovl 1
[ 4.795745] OMAPFB: create_framebuffers done
[ 4.795898] OMAPFB: mgr->apply'ed
[ 4.831756] OMAPFB: size_notify: 640x480
[ 4.831787] OMAPFB: check_var(0)
[ 4.831817] OMAPFB: check_fb_var 0
[ 4.831817] OMAPFB: max frame size 25165824, line size 2560
[ 4.831848] OMAPFB: xres = 640, yres = 480, vxres = 640, vyres = 480
[ 4.930877] omapdss DISPC error: timeout waiting for EVSYNC
[ 4.930908] OMAPFB: create sysfs for fbs
[ 4.930908] OMAPFB: create sysfs for fbs
[ 4.931243] OMAPFB: set_par(0)
[ 4.931243] OMAPFB: set_fb_fix
[ 4.931243] OMAPFB: apply_changes, fb 0, ovl 0
[ 4.931243] OMAPFB: setup_overlay 0, posx 0, posy 0, outw 640, outh 480
[ 4.931274] OMAPFB: paddr 9ae00000, vaddr de000000
[ 4.931396] OMAPFB: pan_display(0)
[ 4.931396] OMAPFB: setcmap
[ 4.931488] OMAPFB: pan_display(0)
[ 4.931488] OMAPFB: setcmap
[ 4.931488] OMAPFB: pan_display(0)
[ 4.931488] OMAPFB: setcmap
[ 4.931518] OMAPFB: setcmap
[ 4.943908] OMAPFB: size_notify: 640x480
[ 4.943939] OMAPFB: check_var(1)
[ 4.943969] OMAPFB: check_fb_var 1
[ 4.943969] OMAPFB: cannot convert var to omap dss mode
[ 4.944519] regulator_init_complete: CLK32KG: incomplete constraints,
leaving on
[ 4.957946] regulator_init_complete: VAUX3_6030: incomplete
constraints, leaving on
[ 4.972686] regulator_init_complete: VAUX2_6030: incomplete
constraints, leaving on
[ 4.987152] regulator_init_complete: VDAC: incomplete constraints,
leaving on
[ 4.998077] regulator_init_complete: VCXIO: incomplete constraints,
leaving on
[ 5.012176] regulator_init_complete: VANA: incomplete constraints,
leaving on
[ 5.023101] regulator_init_complete: VPP: incomplete constraints,
leaving on
[ 5.034027] regulator_init_complete: VUSB: incomplete constraints,
leaving on
[ 5.045715] twl_rtc twl_rtc: setting system clock to 2000-01-01
00:40:32 UTC (946687232)
[ 5.060729] omap_vout omap_vout: 'hdmi' Display already enabled
[ 5.070098] omap_vout omap_vout: 'hdmi' Display already enabled
[ 5.079498] omap_vout omap_vout: Buffer Size = 3686400
[ 5.089721] omap_vout omap_vout: : registered and initialized video
device 0
[ 5.101867] Freeing init memory: 252K
[ 5.114227] smsc95xx 1-1.1:1.0: eth0: register 'smsc95xx' at
usb-ehci-omap.0-1.1, smsc95xx USB 2.0 Ethernet, 2e:40:70:f0:12:06
[ 5.264251] <30>udev[699]: starting version 167
[ 5.368682] usb 1-1.3: new low speed USB device number 4 using ehci-omap
[ 5.582122] usb 1-1.3: New USB device found, idVendor=062a,
idProduct=0000
[ 5.592468] usb 1-1.3: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 5.615661] input: HID 062a:0000 as
/devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input0
[ 5.635437] generic-usb 0003:062A:0000.0001: input: USB HID v1.10
Mouse [HID 062a:0000] on usb-ehci-omap.0-1.3/input0
[ 5.977111] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data
mode. Opts: (null)
[ 6.947784] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro
[ 7.108825] <30>udev[875]: starting version 167
[ 8.573730] OMAPFB: pan_display(0)
[ 8.573760] OMAPFB: setcmap
[ 8.573760] OMAPFB: setcmap
[ 8.580718] OMAPFB: setcmap
[ 8.627288] OMAPFB: pan_display(0)
[ 8.627288] OMAPFB: setcmap
[ 8.627319] OMAPFB: setcmap
[ 8.759185] cfg80211: Updating information on frequency 2412 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759185] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759216] cfg80211: Updating information on frequency 2417 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759216] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759216] cfg80211: Updating information on frequency 2422 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759246] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759246] cfg80211: Updating information on frequency 2427 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759277] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759277] cfg80211: Updating information on frequency 2432 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759277] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759307] cfg80211: Updating information on frequency 2437 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759307] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759307] cfg80211: Updating information on frequency 2442 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759338] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759338] cfg80211: Updating information on frequency 2447 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759368] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759368] cfg80211: Updating information on frequency 2452 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759368] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759399] cfg80211: Updating information on frequency 2457 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759399] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759399] cfg80211: Updating information on frequency 2462 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759429] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759429] cfg80211: Updating information on frequency 2467 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759460] cfg80211: 2457000 KHz - 2482000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759490] cfg80211: Updating information on frequency 2472 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759490] cfg80211: 2457000 KHz - 2482000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759521] cfg80211: Updating information on frequency 2484 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759521] cfg80211: 2474000 KHz - 2494000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759521] cfg80211: Disabling freq 5035 MHz
[ 8.759552] cfg80211: Disabling freq 5040 MHz
[ 8.759552] cfg80211: Disabling freq 5045 MHz
[ 8.759552] cfg80211: Disabling freq 5055 MHz
[ 8.759582] cfg80211: Disabling freq 5060 MHz
[ 8.759582] cfg80211: Disabling freq 5080 MHz
[ 8.759582] cfg80211: Disabling freq 5170 MHz
[ 8.759613] cfg80211: Updating information on frequency 5180 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759613] cfg80211: 5170000 KHz - 5250000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759643] cfg80211: Updating information on frequency 5190 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759643] cfg80211: 5170000 KHz - 5250000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759674] cfg80211: Updating information on frequency 5200 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759674] cfg80211: 5170000 KHz - 5250000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759674] cfg80211: Updating information on frequency 5210 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759704] cfg80211: 5170000 KHz - 5250000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759704] cfg80211: Updating information on frequency 5220 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759735] cfg80211: 5170000 KHz - 5250000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759735] cfg80211: Updating information on frequency 5230 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759765] cfg80211: 5170000 KHz - 5250000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759765] cfg80211: Updating information on frequency 5240 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759765] cfg80211: 5170000 KHz - 5250000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759796] cfg80211: Disabling freq 5260 MHz
[ 8.759796] cfg80211: Disabling freq 5280 MHz
[ 8.759796] cfg80211: Disabling freq 5300 MHz
[ 8.759826] cfg80211: Disabling freq 5320 MHz
[ 8.759826] cfg80211: Disabling freq 5500 MHz
[ 8.759826] cfg80211: Disabling freq 5520 MHz
[ 8.759826] cfg80211: Disabling freq 5540 MHz
[ 8.759857] cfg80211: Disabling freq 5560 MHz
[ 8.759857] cfg80211: Disabling freq 5580 MHz
[ 8.759857] cfg80211: Disabling freq 5600 MHz
[ 8.759857] cfg80211: Disabling freq 5620 MHz
[ 8.759887] cfg80211: Disabling freq 5640 MHz
[ 8.759887] cfg80211: Disabling freq 5660 MHz
[ 8.759887] cfg80211: Disabling freq 5680 MHz
[ 8.759887] cfg80211: Disabling freq 5700 MHz
[ 8.759918] cfg80211: Updating information on frequency 5745 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759918] cfg80211: 5735000 KHz - 5835000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759948] cfg80211: Updating information on frequency 5765 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759948] cfg80211: 5735000 KHz - 5835000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759948] cfg80211: Updating information on frequency 5785 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759979] cfg80211: 5735000 KHz - 5835000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.759979] cfg80211: Updating information on frequency 5805 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.759979] cfg80211: 5735000 KHz - 5835000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.760009] cfg80211: Updating information on frequency 5825 MHz for
a 20 MHz width channel with regulatory rule:
[ 8.760009] cfg80211: 5735000 KHz - 5835000 KHz @ KHz), (600 mBi,
2000 mBm)
[ 8.882843] wl1271: loaded
[ 8.882873] wl1271: initialized
[ 10.604858] OMAPFB: pan_display(0)
[ 10.604858] OMAPFB: setcmap
[ 10.604858] OMAPFB: setcmap
[ 10.648101] OMAPFB: user mmap region start 9ae00000, len 25165824,
off 9ae00000
[ 10.688232] wl1271: firmware booted (Rev 6.1.3.50.55)
[ 10.692871] ieee80211 phy0: device now idle
[ 10.744415] omapdss DISPC error: timeout waiting for EVSYNC
[ 10.845001] omapdss DISPC error: timeout waiting for EVSYNC
[ 10.858245] OMAPFB: pan_display(0)
[ 10.871459] OMAPFB: setcmap
...
[ 10.874389] OMAPFB: setcmap
[ 11.110870] ieee80211 phy0: device no longer idle - scanning
[ 11.565673] OMAPFB: size_notify: 640x480
[ 11.665191] omapdss DISPC error: timeout waiting for EVSYNC
[ 11.766784] omapdss DISPC error: timeout waiting for EVSYNC
[ 11.778564] OMAPFB: check_var(0)
[ 11.778594] OMAPFB: check_fb_var 0
[ 11.778594] OMAPFB: max frame size 25165824, line size 2560
[ 11.778594] OMAPFB: xres = 640, yres = 480, vxres = 640, vyres = 480
[ 11.778625] OMAPFB: set_par(0)
[ 11.778625] OMAPFB: set_fb_fix
[ 11.778625] OMAPFB: apply_changes, fb 0, ovl 0
[ 11.778625] OMAPFB: setup_overlay 0, posx 0, posy 0, outw 640, outh 480
[ 11.778656] OMAPFB: paddr 9ae00000, vaddr de000000
[ 11.778717] OMAPFB: pan_display(0)
[ 11.778717] OMAPFB: setcmap
[ 11.778778] OMAPFB: size_notify: 640x480
[ 11.778778] OMAPFB: check_var(1)
[ 11.778778] OMAPFB: check_fb_var 1
[ 11.778778] OMAPFB: cannot convert var to omap dss mode
-Andy
_______________________________________________
linaro-dev mailing list
linaro-dev@lists.linaro.org
http://lists.linaro.org/mailman/listinfo/linaro-dev
