Dietmar, Nobody else jumped on this, so maybe I can help...
Is this Linux/390 system running in an LPAR? If so, did you try specifying IPLdelay=xyz in your parmfile? You might start with a value of IPLdelay=2m and see if that helps. (But only for an LPAR install.) I guess I should ask if the system is already installed, or are you trying to install it? What distribution are you using? We had one instance where someone trying to get Red Hat installed in an LPAR with an OSA card _never_ got it to work, but SuSE did. Strange, I know, but... When you bring up the system, there might be/should be some messages on the console that talk about device detection. Any of those relating to the OSA card might be of some value. Mark Post -----Original Message----- From: Dietmar Rueger [mailto:[EMAIL PROTECTED]] Sent: Monday, December 02, 2002 2:16 PM To: [EMAIL PROTECTED] Subject: 3172 lcs problem Hallo list, I don't know what a "partially successful startup" with rc= -4 means. The 3172 runs fine with a VSE TCPIP stack ... I checked the archive and am running out of ideas now. Any help is greatly appreciated. Starting lcs module $Revision: 1.120.2.6 $ $Date: 2002/03/01 16:51:06 $ with chandev support,with multicast support, with ethernet support, with token ring support. debug: lcs: new level 0 lcs_sleepon network card taking time responding irq=000b devno=0f42, please be patient, ctrl-c will exit if shell prompt is available. qipassist failed, ipassists assumed unsupported for tr0 lcs: tr0 configured as follows read subchannel=b write subchannel=c read_devno=0f42 write_devno=0f43 hw_address=08:00:5A:0C:E0:21 rel_adapter_no=1 lcs_sleepon network card taking time responding irq=000b devno=0f42, please be patient, ctrl-c will exit if shell prompt is available. A partially successful startup read_devno=0f42 write_devno= f43 was detected rc=-4 please check your configuration parameters,cables & connection to the network. SIOCSIFFLAGS: No such device /etc/chandev.conf noauto;lcs0,0x0f42,0x0f43,0,1 /etc/modules.conf alias tr0 lcs /etc/rc.config NETDEV_2="tr0" IFCONFIG_2="90.0.1.51 broadcast 90.255.255.255 netmask 255.0.0.0 mtu 2000 up" /proc/chandev: Forced devices chan defif read write data memory port ip type num devno devno devno usage(k) protocol no. chksum ================================================================ 0x04 0 0x0f42 0x0f43 0x0000 default 1 0 0 0x10 0 0x0500 0x0501 0x0502 default 0 0 0 Registered probe functions probefunc shutdownfunc msck_notfunc chan devices devices type found active =============================================================== 0x20a170c4 0x20a1745c 0x20a174d4 0x04 1 1 0x209d078c 0x209d3fe4 0x209d04e0 0x10 1 1 Initialised Devices read write data read write data chan port dev dev memory irq irq irq devno devno devno type no. ptr name usage(k) ========================================================================== 0x0008 0x0009 0x000a 0x0500 0x0501 0x0502 0x10 0 0x1ffdf200 hsi0 2048 0x000b 0x000c n/a 0x0f42 0x0f43 n/a 0x04 1 0x1ffdf000 tr0 320 Total device memory usage 2368k. channels detected chan cu cu dev dev in chandev irq devno type type model type model pim chpids use reg. ============================================================================ === 0x0008 0x0500 0x10 0x1731 0x05 0x1732 0x05 0x80 0x0100000000000000 yes yes 0x0009 0x0501 0x10 0x1731 0x05 0x1732 0x05 0x80 0x0100000000000000 yes yes 0x000a 0x0502 0x10 0x1731 0x05 0x1732 0x05 0x80 0x0100000000000000 yes yes 0x000b 0x0f42 0x04 0x3088 0x01 0x0000 0x00 0x80 0x10ffffffffffffff yes yes 0x000c 0x0f43 0x04 0x3088 0x01 0x0000 0x00 0x80 0x10ffffffffffffff yes yes Dietmar Rueger NMC Informationssysteme GmbH mailto:[EMAIL PROTECTED]