Hi Ranga I have finally resolved the problem , I will update incase someone goes thru the same, The initial Dasd was HDS and I moved to IBM ( same as current install) also on the " DASD Module Parameter Setting" Panel I added the "dasd=xxxx,xxxx" values and installed as normal . I will confirm if HDS disk is a problem with another sandbox box install.
Regards Gerard -----Original Message----- From: Ranga Nathan [mailto:[EMAIL PROTECTED] Sent: 20 April 2005 06:14 PM To: Ceruti, Gerard G Cc: LINUX-390@VM.MARIST.EDU Subject: Re: FW: SuSE 8 Installation problem on z800 Gerard: I dont remember! It was a long time ago. One of the problems we had was that the volumes were not INITed for IPL on the z/OS side. When IPLing, the system could not find the boot record. I think we had to run a job to put IPL text on the volumes and then install Linux. The code 000A00000000000F means that the IPL text could not be found. We are currently on z/VM where the volumes are initialized under z/VM. __________________________________________ Ranga Nathan / CSG Systems Programmer - Specialist; Technical Services; BAX Global Inc. Irvine-California Tel: 714-442-7591 Fax: 714-442-2840 "Ceruti, Gerard G" <[EMAIL PROTECTED]> 04/20/2005 02:34 AM To "'Ranga Nathan'" <[EMAIL PROTECTED]> cc Subject FW: SuSE 8 Installation problem on z800 Hi Nathan I am hoping you are able to remember what you did to resolve the problem mentioned below , as I am in the same boat. Many thanks Gerard Ceruti > -----Original Message----- > From: Ranga Nathan [mailto:[EMAIL PROTECTED] > Sent: Friday, December 19, 2003 2:09 PM > To: LINUX-390@VM.MARIST.EDU > Subject: SuSE 8 Installation problem on z800 > > > We have completed the SuSE 8 installation on an LPAR. But we are not > able to IPL. It goes into wait status. Looks like the bootstrap is > missing. We allocated 16 x 3390 volumes (0x2300 to 0x230F) and the > fitst one contains the boot partition. > > When IPLing, we specify 0x2300 as the boot device and no load params. > > What we get is the message: > An error was detected in partition LINUX. Central Processing > (CP) 00 is in > a disabled wait state. The disabled wait PSW is 000A00000000000F. > Central storage bytes 0 - 7 are: 000A00000000000F. > > Anyone encountered this before? > > We tried to reinstall and in yast took the "Boot from ..." option, > which complained about something not mounted and killed my SSH > session. > ____________________________________________________________________________ ______________________________________________________ Standard Bank Disclaimer and Confidentiality Note This e-mail, its attachments and any rights attaching hereto are, unless the context clearly indicates otherwise, the property of Standard Bank Group Limited and/or its subsidiaries ("the Group"). It is confidential, private and intended for the addressee only. Should you not be the addressee and receive this e-mail by mistake, kindly notify the sender, and delete this e-mail, immediately and do not disclose or use same in any manner whatsoever. Views and opinions expressed in this e-mail are those of the sender unless clearly stated as those of the Group. The Group accepts no liability whatsoever for any loss or damages whatsoever and howsoever incurred, or suffered, resulting, or arising, from the use of this email or its attachments. The Group does not warrant the integrity of this e-mail nor that it is free of errors, viruses, interception or interference. Licensed divisions of the Standard Bank Group are authorised financial services providers in terms of the Financial Advisory and Intermediary Services Act, No 37 of 2002 (FAIS). For information about the Standard Bank Group Limited visit our website http://www.standardbank.co.za ____________________________________________________________________________ ______________________________________________________ __________________________________________________________________________________________________________________________________ Standard Bank Disclaimer and Confidentiality Note This e-mail, its attachments and any rights attaching hereto are, unless the context clearly indicates otherwise, the property of Standard Bank Group Limited and/or its subsidiaries ("the Group"). It is confidential, private and intended for the addressee only. Should you not be the addressee and receive this e-mail by mistake, kindly notify the sender, and delete this e-mail, immediately and do not disclose or use same in any manner whatsoever. Views and opinions expressed in this e-mail are those of the sender unless clearly stated as those of the Group. The Group accepts no liability whatsoever for any loss or damages whatsoever and howsoever incurred, or suffered, resulting, or arising, from the use of this email or its attachments. The Group does not warrant the integrity of this e-mail nor that it is free of errors, viruses, interception or interference. Licensed divisions of the Standard Bank Group are authorised financial services providers in terms of the Financial Advisory and Intermediary Services Act, No 37 of 2002 (FAIS). For information about the Standard Bank Group Limited visit our website http://www.standardbank.co.za ___________________________________________________________________________________________________________________________________ ---------------------------------------------------------------------- For LINUX-390 subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: INFO LINUX-390 or visit http://www.marist.edu/htbin/wlvindex?LINUX-390
