Everything looks good from the log. The OSA driver loads and the interface gets configured. Is the /28 subnet mask correct for your system? That equates to 255.255.255.240.
What system are you pinging from? Is it on the same subnet (Guest LAN?) If not, are there any firewalls in between that might be dropping icmp packets? You might just try re-IPLing from 200 and see if it goes away (without doing a complete reinstall just yet), because it might just be a glitch. Mark Post -----Original Message----- From: Linux on 390 Port [mailto:[EMAIL PROTECTED] On Behalf Of [EMAIL PROTECTED] Sent: Thursday, August 11, 2005 9:31 PM To: LINUX-390@VM.MARIST.EDU Subject: Can't Access YAST to complete install Hello All, I'm working on installing SLES9 with SP2 on z/VM 4.4 and have trouble after the reboot. I'm installing from a NFS server and access all the media fine. OSA Express attached and using MPROUTE in VM for OSPF. I currently have SLES8 up in this environment without problems. I go through the initial IPL from the RDR Enter all the IP and NFS info then successfully connect via VNC to do the install in YAST Dasd formats fine. (Virt Device is 0x0200 3390-3 ) Partitions without error I select minimal install and set the TZ and set run level to 3 Install completes without error system reboots, I IPL 200 and SUSE begins to load, gets to the point that it says to reconnect to VNC. UNABLE to connect to VNC, Can not ping the IP of the guest. below is the log as it starting after the install to begin the customization step 00: IPL 200 00: Booting default (ipl)... Linux version 2.6.5-7.191-s390 ([EMAIL PROTECTED]) (gcc version 3.3.3 (SuSE Linux) ) #1 SMP Tue Jun 28 14:58:56 UTC 2005 We are running under VM (31 bit mode) This machine has an IEEE fpu On node 0 totalpages: 262144 DMA zone: 262144 pages, LIFO batch:31 Normal zone: 0 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 Built 1 zonelists Kernel command line: root=/dev/dasda1 selinux=0 TERM=dumb elevator=cfq BOOT_IMAGE=0 PID hash table entries: 4096 (order 12: 32768 bytes) CKRM Initialization ...... Initializing ClassType<taskclass> ........ ...... Initializing ClassType<socketclass> ........ CKRM Initialization done Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes) Inode-cache hash table entries: 131072 (order: 7, 524288 bytes) Memory: 1029632k/1048576k available (3255k kernel code, 0k reserved, 1111k data, 100k init) Security Scaffold v1.0.0 initialized SELinux: Disabled at boot. Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Detected 2 CPU's Boot cpu address 0 cpu 0 phys_idx=0 vers=FF ident=0F32CD machine=2084 unused=8000 cpu 1 phys_idx=1 vers=FF ident=0F32CD machine=2084 unused=8000 Brought up 2 CPUs checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 1559k freed khelper: max 64 concurrent processes debug: Initialization complete resid is -1 name is io <NULL> CKRM .. create res clsobj for resouce <io>class <taskclass> par=00000000 NET: Registered protocol family 16 VFS: Disk quotas dquot_6.5.1 Initializing Cryptographic API RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize loop: loaded (max 8 devices) md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 Channel measurement facility using extended format (autodetected) NET: Registered protocol family 2 IP: routing cache hash table of 8192 buckets, 64Kbytes TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 262144 bind 65536) NET: Registered protocol family 1 resid is -1 name is cpu <NULL> CKRM .. create res clsobj for resouce <cpu>class <taskclass> par=00000000 ........init_ckrm_sched_res , resid= 5 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). Starting udev Creating devices Loading kernel/fs/jbd/jbd.ko Loading kernel/fs/ext3/ext3.ko Loading kernel/drivers/s390/block/dasd_mod.ko Loading kernel/drivers/s390/block/dasd_eckd_mod.ko Loading kernel/drivers/s390/block/dasd_fba_mod.ko Activating DASDs: 0.0.0200:0Configuring device 0.0.0200 Setting device online dasd(eckd): 0.0.0200: 3390/0A(CU:3990/01) Cyl:3338 Head:15 Sec:224 Using cfq io scheduler dasd(eckd): 0.0.0200: (4kB blks): 2403360kB at 48kB/trk compatible disk layout dasda:VOL1/ 0X0200: dasda1 0.0.0203:0Configuring device 0.0.0203 Setting device online dasd(eckd): 0.0.0203: 3390/0A(CU:3990/01) Cyl:1338 Head:15 Sec:224 dasd(eckd): 0.0.0203: (4kB blks): 963360kB at 48kB/trk compatible disk layout dasdb:VOL1/ 0X0203: dasdb1 0.0.0204:0Configuring device 0.0.0204 Setting device online dasd(fba): 0.0.0204: 9336/10(CU:6310/80) 128MB at(512 B/blk) dasdc:CMS1/ SWAP (MDSK): dasdc1 : done Waiting for device /dev/dasda1 to appear: ok rootfs: major=94 minor=1 devn=24065 rootfs: /sys/block/dasda/dasda1 major=94 minor=1 devn=24065 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Trying to move old root to /initrd ... failed Unmounting old root Trying to free ramdisk memory ... failed Freeing unused kernel memory: 100k freed INIT: version 2.85 booting System Boot Control: Running /etc/init.d/boot Mounting /proc filesystem..done Mounting sysfs on /sys..done Mounting /dev/pts..done Boot logging started on /dev/ttyS0(/dev/console) at Thu Aug 11 22:22:17 2005 Mounting shared memory FS on /dev/shm..done Activating swap-devices in /etc/fstab... Adding 963256k swap on /dev/dasdb1. Priority:42 extents:1 Adding 130900k swap on /dev/dasdc1. Priority:42 extents:1 [1A..doneChecking root file system... fsck 1.36 (05-Feb-2005) [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a /dev/dasda1 /dev/dasda1: Backing up journal inode block information. /dev/dasda1: clean, 31967/300960 files, 139453/600816 blocks [1A..doneEXT3 FS on dasda1, internal journal md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. Activating device mapper... device-mapper: Allocated new minor_bits array for 1024 devices device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [EMAIL PROTECTED] Creating /dev/mapper/control character device with major:10 minor:63. ..done Checking file systems... fsck 1.36 (05-Feb-2005) Checking all file systems. [1A..doneJBD: barrier-based sync failed on dasda1 - disabling barriers Setting up..done Mounting local file systems... proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) tmpfs on /dev/shm type tmpfs (rw) devpts on /dev/pts type devpts (rw,mode=0620,gid=5) nothing was mounted [1A..doneActivating remaining swap-devices in /etc/fstab... [1A..doneLoading required kernel modules [1A..doneSetting up the system clock..done Restore device permissions..done Creating /var/log/boot.msg [1A..doneSetting up timezone data..done Setting scheduling timeslices ..unused Setting current sysctl status from /etc/sysctl.conf net.ipv4.icmp_echo_ignore_broadcasts = 1 net.ipv4.conf.all.rp_filter = 1 ..done Setting up hostname 'cohzlnx06'..done Setting up loopback interface lo lo IP address: 127.0.0.1/8 ..done Enabling syn flood protection..done Disabling IP forwarding..done ..done System Boot Control: The system has been set up Skipped features: [80C [17Dboot.sched System Boot Control: Running /etc/init.d/boot.local [1A..doneStarting syslog services..done unicode_start skipped on /dev/ttyS0 enabling Hotplug ..done coldplug scanning ccw: ***NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver qdio: loading QDIO base support version 2 ($Revision: 1.79.2.8 $/$Revision: 1.57 $/$Revision: 1.23.2.2 $) qeth: loading qeth S/390 OSA-Express driver ($Revision: 1.77.2.47 $/$Revision: 1 .98.2.24 $/$Revision: 1.27.2.8 $/$Revision: 1.8.2.2 $/$Revision: 1.7.2.2 $/$Revi sion: 1.5.2.6 $/$Revision: 1.19.2.15 $ :IPv6 :VLAN) *..done scanning input: ..done . . . . . . . . . . . . . . . . . . . . . . . .. .done qeth: Device 0.0.5000/0.0.5001/0.0.5002 is a Guest LAN QDIO card (level: V445) with link type GuestLAN QDIO (portname: GUESTLAN) qeth: Hardware IP fragmentation not supported on eth0 qeth: VLAN enabled qeth: Multicast enabled qeth: IPV6 enabled qeth: Broadcast enabled qeth: Could not set up broadcast echo filtering on eth0: 0x2 qeth: Using SW checksumming on eth0. qeth: Outbound TSO not supported on eth0 Hint: you may set mandatory devices in /etc/sysconfig/network/config Setting up network interfaces: lo lo IP address: 127.0.0.1/8 [1A..done eth0 eth0 configuration: qeth-bus-ccw-0.0.5000 eth0 IP address: 155.180.147.41/28 [1A..doneSetting up service network . . . . . . . . . . . . . . . ...done Generating /etc/ssh/ssh_host_key. Generating public/private rsa1 key pair. Your identification has been saved in /etc/ssh/ssh_host_key. Your public key has been saved in /etc/ssh/ssh_host_key.pub. The key fingerprint is: fc:6a:e2:56:7d:ea:0d:89:a7:4f:af:ca:d6:44:58:1a [EMAIL PROTECTED] Generating /etc/ssh/ssh_host_dsa_key. Generating public/private dsa key pair. Aug 11 18:22:37 cohzlnx06 kernel: klogd 1.4.1, log source = /proc/kmsg started. Aug 11 18:22:37 cohzlnx06 kernel: NET: Registered protocol family 10 Aug 11 18:22:37 cohzlnx06 kernel: IPv6 over IPv4 tunneling driver Aug 11 18:22:37 cohzlnx06 kernel: qdio: loading QDIO base support version 2 ($Re vision: 1.79.2.8 $/$Revision: 1.57 $/$Revision: 1.23.2.2 $) Aug 11 18:22:37 cohzlnx06 kernel: qeth: loading qeth S/390 OSA-Express driver ($ Revision: 1.77.2.47 $/$Revision: 1.98.2.24 $/$Revision: 1.27.2.8 $/$Revision: 1. 8.2.2 $/$Revision: 1.7.2.2 $/$Revision: 1.5.2.6 $/$Revision: 1.19.2.15 $ :IPv6 : VLAN) Aug 11 18:22:37 cohzlnx06 kernel: qeth: Device 0.0.5000/0.0.5001/0.0.5002 is a Guest LAN QDIO card (level: V445) Aug 11 18:22:37 cohzlnx06 kernel: with link type GuestLAN QDIO (portname: GUESTLAN) Aug 11 18:22:37 cohzlnx06 kernel: qeth: Hardware IP fragmentation not supported on eth0 Aug 11 18:22:37 cohzlnx06 kernel: qeth: VLAN enabled Aug 11 18:22:37 cohzlnx06 kernel: qeth: Multicast enabled Aug 11 18:22:37 cohzlnx06 kernel: qeth: IPV6 enabled Aug 11 18:22:37 cohzlnx06 kernel: qeth: Broadcast enabled Aug 11 18:22:37 cohzlnx06 kernel: qeth: Could not set up broadcast echo filtering on eth0: 0x2 Aug 11 18:22:37 cohzlnx06 kernel: qeth: Using SW checksumming on eth0. Aug 11 18:22:37 cohzlnx06 kernel: qeth: Outbound TSO not supported on eth0 Aug 11 18:22:38 cohzlnx06 ifup: No configuration found for sit0 Your identification has been saved in /etc/ssh/ssh_host_dsa_key. Your public key has been saved in /etc/ssh/ssh_host_dsa_key.pub. The key fingerprint is: df:a5:90:46:4f:fc:9d:77:3a:b2:d5:75:04:a8:7c:26 [EMAIL PROTECTED] Generating /etc/ssh/ssh_host_rsa_key. Generating public/private rsa key pair. Your identification has been saved in /etc/ssh/ssh_host_rsa_key. Your public key has been saved in /etc/ssh/ssh_host_rsa_key.pub. The key fingerprint is: b3:5a:9a:a4:a0:12:f8:47:cc:50:4d:1b:2f:04:3c:87 [EMAIL PROTECTED] Starting SSH daemon..done *** *** Please return to your X-Server screen to finish installation *** starting VNC server... a log can be found in /tmp/vncserver.log ... *** *** You can connect to 155.180.147.41, display :1 now with vncviewer *** Or use a Java capable browser on http://155.180.147.41:5801/ *** (When YaST2 is finished, close your VNC viewer and return to this window.) Aug 11 18:22:45 cohzlnx06 kernel: eth0: no IPv6 routers present SCSI subsystem initialized Aug 11 18:22:51 cohzlnx06 kernel: SCSI subsystem initialized st: Version 20040318, fixed bufsize 32768, s/g segs 256 Aug 11 18:22:51 cohzlnx06 kernel: st: Version 20040318, fixed bufsize 32768, s/g segs 256 At this point I can not Ping the 155.180.147.41 address so i can not finish the installation has anyone seen this? William 'Doug' Carroll Mainframe Systems Engineer II Global Technology Infrastructure (614) 213-4954 Office (877) 899-1697 Pager (614) 244-9897 Fax http://www.bankone.com http://www.jpmchase.com ---------------------------------------------------------------------- For LINUX-390 subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: INFO LINUX-390 or visit http://www.marist.edu/htbin/wlvindex?LINUX-390 ---------------------------------------------------------------------- For LINUX-390 subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: INFO LINUX-390 or visit http://www.marist.edu/htbin/wlvindex?LINUX-390
