Output is [root@linux12 ~]# vmcp q v fcp FCP 260C ON FCP 260C CHPID AE SUBCHANNEL = 000F 260C DEVTYPE FCP VIRTUAL CHPID AE FCP REAL CHPID AE 260C QDIO ACTIVE QIOASSIST DISABLED 260C 260C INP + 01 IOCNT = 00000010 ADP = 128 PROG = 000 UNAVAIL = 000 260C BYTES = 0000000000000000 260C OUT + 01 IOCNT = 00000027 ADP = 000 PROG = 027 UNAVAIL = 101 260C BYTES = 0000000000018254 260C DATA ROUTER ELIGIBLE FCP 271C ON FCP 271C CHPID AF SUBCHANNEL = 0010 271C DEVTYPE FCP VIRTUAL CHPID AF FCP REAL CHPID AF 271C QDIO-ELIGIBLE QIOASSIST DISABLED 271C DATA ROUTER ELIGIBLE [root@linux12 ~]#
On Tue, Nov 4, 2014 at 5:37 PM, Offer Baruch <offerbar...@gmail.com> wrote: > Hi > > The /scrarch directory is based on the sda device... > The fact that lsscsi does not return output means that sda is missing and > that is why you dont have that directory mounted. > > Can you add the output of the following command please? > vmcp q v fcp > > Have a good day > Offer Baruch > On Nov 4, 2014 2:37 AM, "Mainframe Mainframe" <mainframe1...@gmail.com> > wrote: > > > Hello, > > We have multiple zlinux (RHEL 6) system with below USER DIRECT > > entries > > > > MDISK 0200 3390 1 END LX131F MR FARM SLES9 SP3 > > MDISK 0207 FB-512 V-DISK 4194296 MR > > > > but we facing issue that directory "/scratch/prod/" is missing . For > > isolating issue, when I checked lsscsi command I am getting blank output > in > > nonworking system but in other system I am getting > > > > linux12:/sys/bus/ccw/drivers/zfcp # lsscsi > > [0:0:0:1074675744]disk IBM 2107900 .278 /dev/sda > > [0:0:0:1075527712]disk IBM 2107900 .278 /dev/sdb > > > > I also checked lsdasd command on both wokring and nonworking system but > > output is same. > > > > > > 0.0.0200(ECKD) at ( 94: 0) is dasda : active at blocksize 4096, > > 3605940 blocks, 14085 MB > > 0.0.0207(FBA ) at ( 94: 28) is dasdh : active at blocksize 512, > > 4194296 blocks, 2047 MB > > > > I also checked fstab entry and both have same > > > > linux12:/sys/bus/ccw/drivers/zfcp # cat /etc/fstab > > /dev/dasda1 / ext3 acl,user_xattr > > 1 1 > > proc /proc proc defaults > > 0 0 > > sysfs /sys sysfs noauto > > 0 0 > > debugfs /sys/kernel/debug debugfs noauto > > 0 0 > > devpts /dev/pts devpts mode=0620,gid=5 > > 0 0 > > /dev/sda1 /scratch ext3 defaults 1 0 > > > > can anybody suggest, what else should i be looking into to isolate this > > issue. > > > > ---------------------------------------------------------------------- > > For LINUX-390 subscribe / signoff / archive access instructions, > > send email to lists...@vm.marist.edu with the message: INFO LINUX-390 or > > visit > > http://www.marist.edu/htbin/wlvindex?LINUX-390 > > ---------------------------------------------------------------------- > > For more information on Linux on System z, visit > > http://wiki.linuxvm.org/ > > > > ---------------------------------------------------------------------- > For LINUX-390 subscribe / signoff / archive access instructions, > send email to lists...@vm.marist.edu with the message: INFO LINUX-390 or > visit > http://www.marist.edu/htbin/wlvindex?LINUX-390 > ---------------------------------------------------------------------- > For more information on Linux on System z, visit > http://wiki.linuxvm.org/ > ---------------------------------------------------------------------- For LINUX-390 subscribe / signoff / archive access instructions, send email to lists...@vm.marist.edu with the message: INFO LINUX-390 or visit http://www.marist.edu/htbin/wlvindex?LINUX-390 ---------------------------------------------------------------------- For more information on Linux on System z, visit http://wiki.linuxvm.org/