On Thu, Apr 06, 2000 at 06:36:57PM -0400, Hal Burgiss wanted to say the following:
> On Thu, Apr 06, 2000 at 02:10:12PM -0700, The Enlightened Penguin wrote:
> > But I'm having another problem. I'm running 2.2.12-20 with the
> > lm_sensors package. Apparently, lm_sensors is seeing the LM78s as
> > LM75s, and thus only getting temperature info (no voltages).
> >
> > 1) Am I wrong about the existence of LM78s? Are they truly LM75s?
> > 2) Anyone else have this problem?
> > 3) Anyone solve it?
>
> What version? Maybe you are running an older version. I think the
> current one is 2.4.5 which does everything right (well, mostly) except
> fan rpms, but I have the original intel fans which won't work for
> this.
I can second that.
($:~)-> sensors
w83782d-isa-0290
Adapter: ISA adapter
Algorithm: ISA algorithm
VCore 1: +2.03 V (min = +1.80 V, max = +2.20 V)
VBat: +1.50 V (min = +1.80 V, max = +2.20 V)
+3.3V: +3.40 V (min = +2.97 V, max = +3.63 V)
+5V: +5.07 V (min = +4.50 V, max = +5.48 V)
+12V: +12.16 V (min = +10.79 V, max = +13.11 V)
-12V: -12.24 V (min = -13.21 V, max = -10.90 V)
-5V: -5.01 V (min = -5.51 V, max = -4.51 V)
V5SB: +5.16 V (min = +4.50 V, max = +5.48 V)
VCore 2: +2.04 V (min = +2.70 V, max = +3.29 V)
fan1: 5152 RPM (min = 3000 RPM, div = 2)
fan2: 5273 RPM (min = 3000 RPM, div = 2)
fan3: 0 RPM (min = 3000 RPM, div = 2)
temp1: +27 C (limit = +60 C, hysteresis = +50 C, sensor = thermistor)
temp2: +28.5 C (limit = +60.0 C, hysteresis = +50.0 C, sensor =
thermistor)
temp3: +32.0 C (limit = +60.0 C, hysteresis = +50.0 C, sensor =
thermistor)
vid: +2.00 V
alarms: Chassis intrusion detection
beep_enable:
Sound alarm disabled
I am using debian, I installed the stuff with the make-kpkg that is used to
build a .deb of the stuff, but it basically compiles the thing so I dont
think there is much difference. The only thing I changed in sensors.conf was
the VCore 2 -> VBat label change.
I had to boot today because one of the NIC's broke and I had to toss in a
new Tulip based card to replace the old SMC ultra.. After some IRQ conflicts
and the usual Intel Resource Lottery everything works again :)
The temperature values in sensors look pretty accurate even when compared to
the ones in bios (I had a change to check :) - those are pretty low at the
moment because I am still having the case open.
Tuomas
--
-- 1:22pm up 19 min, 7 users, load average: 0.01, 0.11, 0.09 --
.---( t i g e r t @ g i m p . o r g )---.
| some stuff at http://tigert.gimp.org/ |
`---------------------------------------'
--
=- To unsubscribe, email [EMAIL PROTECTED] with the -=
=- body of "unsubscribe linux-abit". -=
