On Fri, 2007-12-28 at 06:00 +0800, Lee Howard wrote: > Hello. > > I frequently work with certain Asterisk-compatible PCI telephony > interfaces that use the "zaptel" module/driver. This module generates > 1000 interrupts per second (yes, I know...) and any noticeable latency > in handling that interrupt can cause significant problems for > modulated > data audio (such as fax) passing through those telephony interfaces. > > It's become apparent that IRQ priorities seem to have to a lot to do > with the performance of the zaptel driver. For example, if the zaptel > device sits on interrupt 16, and the network interfaces and hard drive > interfaces are on higher-numbered interrupts then things tend to go > well. But if the zaptel device sits on interrupt 19, and the network > interfaces and hard drive interfaces are on lesser-numbered interrupts > (such as 16, 17, and 18) then things tend to go poorly. > > The zaptel driver comes with a utility called "zttest" which basically > indicates the reliability for the application to retrieve audio > samples > from the device driver before too much time passes... or in other > words, > the latency (or lack thereof) in handling device interrupts. A good > zttest score on a well-configured system is 100%, although scores as > low > as 99.98% seem to be tolerable for modulated data audio. However, > anything less... 99.97%, 99.96, I've even seen 99.91% and worse... > these > constitute poor scores and inevitably indicate that audio samples will > be lost during usage. (You can see that the difference between "good" > and "poor" is rather a narrow margin.) Lost audio samples is tolerable > for voice applications, but it is detrimental to data/fax > applications. > > Usually the trick, then, has been to simply start rearranging the PCI > cards in the system and disabling unused devices (such as serial, > parallel, and USB ports with the respective drivers) until some > combination was reached where zttest scores were good - inevitably > meaning that the device had a high-priority (low-numbered) interrupt. > > Recently this trick is seemingly more and more difficult to perform... > and it's especially difficult in cases where (like on a 1U rack-mount > server) there is but one PCI slot and the motherboard BIOS offers no > helpful IRQ configuration mechanism. For example, a recent > installation > of Fedora 8 on such a server put the zaptel device at a low-priority > interrupt. After hours of futile BIOS option changes and tests and > even > after testing a kernel (2.6.23.11) patched with Ingo Molnar's "rt" > Real-Time patches (and using chrt for the associated IRQ to increase > priority) nothing seemed to help. Then I simply reverted to an old > 2.6.20 kernel from Fedora Core 5 that we had used successfully on > previous deployments on similar hardware... and all was fine. And, of > course, the apparent difference was that the 2.6.23.11 kernel put the > device interrupt high-numbered while the 2.6.20 kernel put the device > interrupt low-numbered. > > Sometimes, however, it's just not ideal ... or even possible ... to > downgrade to a "known good" kernel. It's certainly not desirable. So > my question is, "How can we deliberately control the IRQ routing > assignments made by ACPI so that certain PCI devices get the > highest-priority interrupts?" > > I've looked into the pirq kernel option ... only to find that it's > insanely difficult to understand *how* to use... and simply trying it > out with various values doesn't seem to accomplish much as far as I > can > tell. (Yes, I have read Documentation/i386/IO-APIC.txt many times... > not that it reading it makes the pirq usage any easier to understand.) > > I've looked into the setpci utility... but besides the man page for it > being mostly unhelpful, it's difficult to know whether or not using > setpci will actually do anything for us in this respect, as there > seems > to be a lot of conflicting information in various posts and mail > archives on whether or not an IRQ assignment can actually be changed > by > using setpci. And then there's the fear that by using setpci > incorrectly I may actually break the hardware. > > I'm fairly certain that this is simply a matter of ACPI tuning... > because with one kernel the interrupt assignments are one way while > with > another kernel the interrupt assignments are a different way... and > both > kernels use IO-APIC and IRQ routing by ACPI. > > I would appreciate any feedback or assistance in this matter. How can > we deliberately control the IRQ routing assignments made by ACPI so > that > certain PCI devices get the highest-priority interrupts? In IOAPIC mode, interrupt priority isn't related with the pin (in your case, irq 16 or 19), but the vector of the pin. How vector of a pin is allocated is quite random. Usually driver who calls pci_enable_device earier will get a lower priority vector.
Thanks, Shaohua - To unsubscribe from this list: send the line "unsubscribe linux-acpi" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html