On Wed, Dec 2, 2015 at 11:33 AM, Vladimir Murzin
<vladimir.mur...@arm.com> wrote:
> This driver adds support to the UART controller found on ARM MPS2
> platform.
Just few comments (have neither time not big desire to do full review).
>
> Signed-off-by: Vladimir Murzin <vladimir.mur...@arm.com>
> ---
> drivers/tty/serial/Kconfig | 12 +
> drivers/tty/serial/Makefile | 1 +
> drivers/tty/serial/mps2-uart.c | 596
> ++++++++++++++++++++++++++++++++++++++
> include/uapi/linux/serial_core.h | 3 +
> 4 files changed, 612 insertions(+)
> create mode 100644 drivers/tty/serial/mps2-uart.c
>
> diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
> index f38beb2..e98bfea 100644
> --- a/drivers/tty/serial/Kconfig
> +++ b/drivers/tty/serial/Kconfig
> @@ -1473,6 +1473,18 @@ config SERIAL_EFM32_UART
> This driver support the USART and UART ports on
> Energy Micro's efm32 SoCs.
>
> +config SERIAL_MPS2_UART_CONSOLE
> + bool "MPS2 UART console support"
> + depends on SERIAL_MPS2_UART
> + select SERIAL_CORE_CONSOLE
> +
> +config SERIAL_MPS2_UART
> + bool "MPS2 UART port"
> + depends on ARM || COMPILE_TEST
> + select SERIAL_CORE
> + help
> + This driver support the UART ports on ARM MPS2.
> +
> config SERIAL_EFM32_UART_CONSOLE
> bool "EFM32 UART/USART console support"
> depends on SERIAL_EFM32_UART=y
> diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
> index 5ab4111..7f589f5 100644
> --- a/drivers/tty/serial/Makefile
> +++ b/drivers/tty/serial/Makefile
> @@ -93,6 +93,7 @@ obj-$(CONFIG_SERIAL_CONEXANT_DIGICOLOR) +=
> digicolor-usart.o
> obj-$(CONFIG_SERIAL_MEN_Z135) += men_z135_uart.o
> obj-$(CONFIG_SERIAL_SPRD) += sprd_serial.o
> obj-$(CONFIG_SERIAL_STM32) += stm32-usart.o
> +obj-$(CONFIG_SERIAL_MPS2_UART) += mps2-uart.o
>
> # GPIOLIB helpers for modem control lines
> obj-$(CONFIG_SERIAL_MCTRL_GPIO) += serial_mctrl_gpio.o
> diff --git a/drivers/tty/serial/mps2-uart.c b/drivers/tty/serial/mps2-uart.c
> new file mode 100644
> index 0000000..09bac16
> --- /dev/null
> +++ b/drivers/tty/serial/mps2-uart.c
> @@ -0,0 +1,596 @@
> +/*
> + * Copyright (C) 2015 ARM Limited
> + *
> + * Author: Vladimir Murzin <vladimir.mur...@arm.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * TODO: support for SysRq
> + */
> +
> +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
> +
> +#include <linux/bitops.h>
> +#include <linux/clk.h>
> +#include <linux/console.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/serial_core.h>
> +#include <linux/tty_flip.h>
> +#include <linux/types.h>
> +
> +#define SERIAL_NAME "ttyMPS"
Can it be ttyS?
> +#define DRIVER_NAME "mps2-uart"
> +#define MAKE_NAME(x) (DRIVER_NAME # x)
> +
> +#define UARTn_DATA 0x0
I think it makes sense to have same width for all offsets, i.e. 0x00
here and so on below.
> +
> +#define UARTn_STATE 0x4
> +#define UARTn_STATE_TX_FULL BIT(0)
> +#define UARTn_STATE_RX_FULL BIT(1)
> +#define UARTn_STATE_TX_OVERRUN BIT(2)
> +#define UARTn_STATE_RX_OVERRUN BIT(3)
> +
> +#define UARTn_CTRL 0x8
> +#define UARTn_CTRL_TX_ENABLE BIT(0)
> +#define UARTn_CTRL_RX_ENABLE BIT(1)
> +#define UARTn_CTRL_TX_INT_ENABLE BIT(2)
> +#define UARTn_CTRL_RX_INT_ENABLE BIT(3)
> +#define UARTn_CTRL_TX_OVERRUN_INT_ENABLE BIT(4)
> +#define UARTn_CTRL_RX_OVERRUN_INT_ENABLE BIT(5)
> +
> +#define UARTn_INT 0xc
> +#define UARTn_INT_TX BIT(0)
> +#define UARTn_INT_RX BIT(1)
> +#define UARTn_INT_TX_OVERRUN BIT(2)
> +#define UARTn_INT_RX_OVERRUN BIT(3)
> +
> +#define UARTn_BAUDDIV 0x10
> +#define UARTn_BAUDDIV_MASK GENMASK(20, 0)
> +
> +#define MPS2_MAX_PORTS 3
> +
> +struct mps2_uart_port {
> + struct uart_port port;
> + struct clk *clk;
> + unsigned int tx_irq;
> + unsigned int rx_irq;
> +};
> +
> +static inline struct mps2_uart_port *to_mps2_port(struct uart_port *port)
> +{
> + return container_of(port, struct mps2_uart_port, port);
> +}
> +
> +static void mps2_uart_write8(struct uart_port *port, u8 val, unsigned off)
> +{
> + struct mps2_uart_port *mps_port = to_mps2_port(port);
> +
> + writeb(val, mps_port->port.membase + off);
> +}
> +
> +static u8 mps2_uart_read8(struct uart_port *port, unsigned off)
> +{
> + struct mps2_uart_port *mps_port = to_mps2_port(port);
> +
> + return readb(mps_port->port.membase + off);
> +}
> +
> +static void mps2_uart_write32(struct uart_port *port, u32 val, unsigned off)
> +{
> + struct mps2_uart_port *mps_port = to_mps2_port(port);
> +
> + writel_relaxed(val, mps_port->port.membase + off);
> +}
> +
> +static unsigned int mps2_uart_tx_empty(struct uart_port *port)
> +{
> + u8 status = mps2_uart_read8(port, UARTn_STATE);
> +
> + return (status & UARTn_STATE_TX_FULL) ? 0 : TIOCSER_TEMT;
> +}
> +
> +static void mps2_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
> +{
> +}
> +
> +static unsigned int mps2_uart_get_mctrl(struct uart_port *port)
> +{
> + return TIOCM_CAR | TIOCM_CTS | TIOCM_DSR;
> +}
> +
> +static void mps2_uart_stop_tx(struct uart_port *port)
> +{
> + u8 control = mps2_uart_read8(port, UARTn_CTRL);
> +
> + control &= ~(UARTn_CTRL_TX_ENABLE |
> + UARTn_CTRL_TX_INT_ENABLE |
> + UARTn_CTRL_TX_OVERRUN_INT_ENABLE);
> +
> + mps2_uart_write8(port, control, UARTn_CTRL);
> +}
> +
> +static void mps2_uart_tx_chars(struct uart_port *port)
> +{
> + struct circ_buf *xmit = &port->state->xmit;
> +
> + while (!(mps2_uart_read8(port, UARTn_STATE) & UARTn_STATE_TX_FULL)) {
> + if (port->x_char) {
> + mps2_uart_write8(port, port->x_char, UARTn_DATA);
> + port->x_char = 0;
> + port->icount.tx++;
> + continue;
> + }
> +
> + if (uart_circ_empty(xmit) || uart_tx_stopped(port))
> + break;
> +
> + mps2_uart_write8(port, xmit->buf[xmit->tail], UARTn_DATA);
> + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
More flexible here to use % UART_XMIT_SIZE. I believe compiler makes it optimal.
> + port->icount.tx++;
> + }
> +
> + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
> + uart_write_wakeup(port);
> +
> + if (uart_circ_empty(xmit))
> + mps2_uart_stop_tx(port);
> +}
> +
> +static void mps2_uart_start_tx(struct uart_port *port)
> +{
> + u8 control = mps2_uart_read8(port, UARTn_CTRL);
> +
> + control |= (UARTn_CTRL_TX_ENABLE |
> + UARTn_CTRL_TX_INT_ENABLE |
> + UARTn_CTRL_TX_OVERRUN_INT_ENABLE);
> +
> + mps2_uart_write8(port, control, UARTn_CTRL);
> + mps2_uart_tx_chars(port);
> +}
> +
> +static void mps2_uart_stop_rx(struct uart_port *port)
> +{
> + u8 control = mps2_uart_read8(port, UARTn_CTRL);
> +
> + control &= ~(UARTn_CTRL_RX_ENABLE |
> + UARTn_CTRL_RX_INT_ENABLE |
> + UARTn_CTRL_RX_OVERRUN_INT_ENABLE);
> +
> + mps2_uart_write8(port, control, UARTn_CTRL);
> +}
> +
> +static void mps2_uart_enable_ms(struct uart_port *port)
> +{
> +}
> +
> +static void mps2_uart_break_ctl(struct uart_port *port, int ctl)
> +{
> +}
Are those required to be present? If not, remove them until you have
alive code there.
> +
> +static void mps2_uart_rx_chars(struct uart_port *port)
> +{
> + struct tty_port *tport = &port->state->port;
> +
> + while (mps2_uart_read8(port, UARTn_STATE) & UARTn_STATE_RX_FULL) {
> + u8 rxdata = mps2_uart_read8(port, UARTn_DATA);
> +
> + port->icount.rx++;
> + tty_insert_flip_char(&port->state->port, rxdata, TTY_NORMAL);
> + }
> +
> + spin_unlock(&port->lock);
> + tty_flip_buffer_push(tport);
> + spin_lock(&port->lock);
> +}
> +
> +static irqreturn_t mps2_uart_rxirq(int irq, void *data)
> +{
> +
> + struct uart_port *port = data;
> + u8 irqflag = mps2_uart_read8(port, UARTn_INT);
> +
> + if (unlikely(!(irqflag & UARTn_INT_RX)))
> + return IRQ_NONE;
> +
> + spin_lock(&port->lock);
> +
> + mps2_uart_write8(port, UARTn_INT_RX, UARTn_INT);
> + mps2_uart_rx_chars(port);
> +
> + spin_unlock(&port->lock);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static irqreturn_t mps2_uart_txirq(int irq, void *data)
> +{
> + struct uart_port *port = data;
> + u8 irqflag = mps2_uart_read8(port, UARTn_INT);
> +
> + if (unlikely(!(irqflag & UARTn_INT_TX)))
> + return IRQ_NONE;
> +
> + mps2_uart_write8(port, UARTn_INT_TX, UARTn_INT);
> + mps2_uart_tx_chars(port);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static irqreturn_t mps2_uart_oerrirq(int irq, void *data)
> +{
> + irqreturn_t handled = IRQ_NONE;
> + struct uart_port *port = data;
> + u8 irqflag = mps2_uart_read8(port, UARTn_INT);
> +
> + spin_lock(&port->lock);
> +
> + if (irqflag & UARTn_INT_RX_OVERRUN) {
> + struct tty_port *tport = &port->state->port;
> +
> + mps2_uart_write8(port, UARTn_INT_RX_OVERRUN, UARTn_INT);
> + tty_insert_flip_char(tport, 0, TTY_OVERRUN);
> + port->icount.overrun++;
> + handled = IRQ_HANDLED;
> + }
> +
> + /* XXX: this shouldn't happen? */
If shouldn't why it's there? Otherwise better to explain which
conditions may lead to this.
> + if (irqflag & UARTn_INT_TX_OVERRUN) {
> + mps2_uart_write8(port, UARTn_INT_TX_OVERRUN, UARTn_INT);
> + handled = IRQ_HANDLED;
> + }
> +
> + spin_unlock(&port->lock);
> +
> + return handled;
> +}
> +
> +static int mps2_uart_startup(struct uart_port *port)
> +{
> + struct mps2_uart_port *mps_port = to_mps2_port(port);
> + u8 control = mps2_uart_read8(port, UARTn_CTRL);
> + int ret;
> +
> + control &= ~(UARTn_CTRL_RX_ENABLE |
> + UARTn_CTRL_TX_ENABLE |
> + UARTn_CTRL_RX_INT_ENABLE |
> + UARTn_CTRL_TX_INT_ENABLE |
> + UARTn_CTRL_RX_OVERRUN_INT_ENABLE |
> + UARTn_CTRL_TX_OVERRUN_INT_ENABLE);
If you unifyf both RX and TX groups you may use them here, and above.
control &= ~(UART…RX | UART…TX);
Above case just RX. Maybe something alike below.
> +
> + mps2_uart_write8(port, control, UARTn_CTRL);
> +
> + ret = request_irq(mps_port->rx_irq, mps2_uart_rxirq, 0,
> + MAKE_NAME(-rx), mps_port);
> + if (ret) {
> + pr_info("failed to register rxirq (%d)\n", ret);
And why not _err() and even dev_err()? Same for stuff below.
> + goto err_no_rxirq;
> + }
> +
> + ret = request_irq(mps_port->tx_irq, mps2_uart_txirq, 0,
> + MAKE_NAME(-tx), mps_port);
> + if (ret) {
> + pr_info("failed to register txirq (%d)\n", ret);
> + goto err_no_txirq;
> + }
> +
> + ret = request_irq(port->irq, mps2_uart_oerrirq, IRQF_SHARED,
> + MAKE_NAME(-overrun), mps_port);
> +
> + if (ret)
> + pr_info("failed to register oerrirq (%d)\n", ret);
> + else {
Keep style according to requirement.
} else {
> + control |= UARTn_CTRL_RX_ENABLE |
> + UARTn_CTRL_TX_ENABLE |
> + UARTn_CTRL_RX_INT_ENABLE |
> + UARTn_CTRL_TX_INT_ENABLE |
> + UARTn_CTRL_RX_OVERRUN_INT_ENABLE |
> + UARTn_CTRL_TX_OVERRUN_INT_ENABLE;
> +
> + mps2_uart_write8(port, control, UARTn_CTRL);
> +
> + return 0;
> + }
> +
> + free_irq(mps_port->tx_irq, mps_port);
> +err_no_txirq:
> + free_irq(mps_port->rx_irq, mps_port);
> +err_no_rxirq:
> + return ret;
> +}
> +
> +static void mps2_uart_shutdown(struct uart_port *port)
> +{
> + struct mps2_uart_port *mps_port = to_mps2_port(port);
> + u8 control = mps2_uart_read8(port, UARTn_CTRL);
> +
> + control &= ~(UARTn_CTRL_RX_ENABLE |
> + UARTn_CTRL_TX_ENABLE |
> + UARTn_CTRL_RX_INT_ENABLE |
> + UARTn_CTRL_TX_INT_ENABLE |
> + UARTn_CTRL_RX_OVERRUN_INT_ENABLE |
> + UARTn_CTRL_TX_OVERRUN_INT_ENABLE);
TX group + RX group, see above.
> +
> + mps2_uart_write8(port, control, UARTn_CTRL);
> +
> + free_irq(mps_port->rx_irq, mps_port);
> + free_irq(mps_port->tx_irq, mps_port);
> + free_irq(port->irq, mps_port);
> +}
> +
> +static void mps2_uart_set_termios(struct uart_port *port,
> + struct ktermios *new, struct ktermios *old)
> +{
> + unsigned long flags;
> + unsigned int baud, bauddiv;
> +
> + new->c_cflag &= ~(CRTSCTS | CMSPAR);
> + new->c_cflag &= ~CSIZE;
> + new->c_cflag |= CS8;
> + new->c_cflag &= ~PARENB;
> + new->c_cflag &= ~CSTOPB;
> +
> + baud = uart_get_baud_rate(port, new, old,
> + DIV_ROUND_CLOSEST(port->uartclk, UARTn_BAUDDIV_MASK),
> + DIV_ROUND_CLOSEST(port->uartclk, 16));
> +
> + bauddiv = DIV_ROUND_CLOSEST(port->uartclk, baud);
> +
> + spin_lock_irqsave(&port->lock, flags);
> +
> + uart_update_timeout(port, new->c_cflag, baud);
> + mps2_uart_write32(port, bauddiv, UARTn_BAUDDIV);
> +
> + spin_unlock_irqrestore(&port->lock, flags);
> +}
> +
> +static const char *mps2_uart_type(struct uart_port *port)
> +{
> + return (port->type == PORT_MPS2UART) ? DRIVER_NAME : NULL;
> +}
> +
> +static void mps2_uart_release_port(struct uart_port *port)
> +{
> +}
> +
> +static int mps2_uart_request_port(struct uart_port *port)
> +{
> + return 0;
> +}
> +
Same question about empty stubs.
> +static void mps2_uart_config_port(struct uart_port *port, int type)
> +{
> + if (type & UART_CONFIG_TYPE && !mps2_uart_request_port(port))
> + port->type = PORT_MPS2UART;
> +}
> +
> +static int mps2_uart_verify_port(struct uart_port *port, struct
> serial_struct *serinfo)
> +{
> + return -EINVAL;
> +}
> +
> +static const struct uart_ops mps2_uart_pops = {
> + .tx_empty = mps2_uart_tx_empty,
> + .set_mctrl = mps2_uart_set_mctrl,
> + .get_mctrl = mps2_uart_get_mctrl,
> + .stop_tx = mps2_uart_stop_tx,
> + .start_tx = mps2_uart_start_tx,
> + .stop_rx = mps2_uart_stop_rx,
> + .enable_ms = mps2_uart_enable_ms,
> + .break_ctl = mps2_uart_break_ctl,
> + .startup = mps2_uart_startup,
> + .shutdown = mps2_uart_shutdown,
> + .set_termios = mps2_uart_set_termios,
> + .type = mps2_uart_type,
> + .release_port = mps2_uart_release_port,
> + .request_port = mps2_uart_request_port,
> + .config_port = mps2_uart_config_port,
> + .verify_port = mps2_uart_verify_port,
> +};
> +
> +static struct mps2_uart_port mps2_uart_ports[MPS2_MAX_PORTS];
> +
> +#ifdef CONFIG_SERIAL_MPS2_UART_CONSOLE
> +static void mps2_uart_console_putchar(struct uart_port *port, int ch)
> +{
> + while (mps2_uart_read8(port, UARTn_STATE) & UARTn_STATE_TX_FULL)
> + cpu_relax();
> +
> + mps2_uart_write8(port, ch, UARTn_DATA);
> +}
> +
> +static void mps2_uart_console_write(struct console *co, const char *s,
> unsigned int cnt)
> +{
> + struct uart_port *port = &mps2_uart_ports[co->index].port;
> +
> + uart_console_write(port, s, cnt, mps2_uart_console_putchar);
> +}
> +
> +static int mps2_uart_console_setup(struct console *co, char *options)
> +{
> + struct mps2_uart_port *mps_port;
> + int baud = 9600;
> + int bits = 8;
> + int parity = 'n';
> + int flow = 'n';
> +
> + if (co->index < 0 || co->index >= MPS2_MAX_PORTS)
> + return -ENODEV;
> +
> + mps_port = &mps2_uart_ports[co->index];
> +
> + if (options)
> + uart_parse_options(options, &baud, &parity, &bits, &flow);
> +
> + return uart_set_options(&mps_port->port, co, baud, parity, bits,
> flow);
> +}
> +
> +static struct uart_driver mps2_uart_driver;
> +
> +static struct console mps2_uart_console = {
> + .name = SERIAL_NAME,
> + .device = uart_console_device,
> + .write = mps2_uart_console_write,
> + .setup = mps2_uart_console_setup,
> + .flags = CON_PRINTBUFFER,
> + .index = -1,
> + .data = &mps2_uart_driver,
> +};
> +
> +#define MPS2_SERIAL_CONSOLE (&mps2_uart_console)
> +
> +#else
> +#define MPS2_SERIAL_CONSOLE NULL
> +#endif
> +
> +static struct uart_driver mps2_uart_driver = {
> + .driver_name = DRIVER_NAME,
> + .dev_name = SERIAL_NAME,
> + .nr = MPS2_MAX_PORTS,
> + .cons = MPS2_SERIAL_CONSOLE,
> +};
> +
> +static struct mps2_uart_port *mps2_of_get_port(struct platform_device *pdev)
> +{
> + struct device_node *np = pdev->dev.of_node;
> + int id;
> +
> + if (!np)
> + return NULL;
> +
> + id = of_alias_get_id(np, "serial");
> + if (id < 0)
> + id = 0;
> +
> + if (WARN_ON(id >= MPS2_MAX_PORTS))
> + return NULL;
> +
> + mps2_uart_ports[id].port.line = id;
> + return &mps2_uart_ports[id];
> +}
> +
> +static int mps2_init_port(struct mps2_uart_port *mps_port,
> + struct platform_device *pdev)
> +{
> + int ret = 0;
Redundant assignment.
> + struct resource *res;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + mps_port->port.membase = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(mps_port->port.membase))
> + return PTR_ERR(mps_port->port.membase);
> +
> + mps_port->port.mapbase = res->start;
> + mps_port->port.mapsize = resource_size(res);
> +
> + mps_port->rx_irq = platform_get_irq(pdev, 0);
> + mps_port->tx_irq = platform_get_irq(pdev, 1);
> + mps_port->port.irq = platform_get_irq(pdev, 2);
> +
> + mps_port->port.iotype = UPIO_MEM;
> + mps_port->port.flags = UPF_BOOT_AUTOCONF;
> + mps_port->port.fifosize = 1;
> + mps_port->port.ops = &mps2_uart_pops;
> + mps_port->port.dev = &pdev->dev;
> +
> + mps_port->clk = devm_clk_get(&pdev->dev, NULL);
> + if (IS_ERR(mps_port->clk))
> + return PTR_ERR(mps_port->clk);
> +
> + ret = clk_prepare_enable(mps_port->clk);
> + if (ret)
> + return ret;
> +
> + mps_port->port.uartclk = clk_get_rate(mps_port->clk);
> + if (!mps_port->port.uartclk)
> + ret = -EINVAL;
So, 1 is OK, 0 is not. I think 1 is too low to be provided by hardware.
> +
> + clk_disable_unprepare(mps_port->clk);
> +
> + return ret;
> +}
> +
> +static int mps2_serial_probe(struct platform_device *pdev)
> +{
> + struct mps2_uart_port *mps_port;
> + int ret;
> +
> + mps_port = mps2_of_get_port(pdev);
> + if (!mps_port)
> + return -ENODEV;
> +
> + ret = mps2_init_port(mps_port, pdev);
> + if (ret)
> + return ret;
> +
> + ret = uart_add_one_port(&mps2_uart_driver, &mps_port->port);
> + if (ret)
> + return ret;
> +
> + platform_set_drvdata(pdev, mps_port);
> +
> + return 0;
> +}
> +
> +static int mps2_serial_remove(struct platform_device *pdev)
> +{
> + struct mps2_uart_port *mps_port = platform_get_drvdata(pdev);
> +
> + uart_remove_one_port(&mps2_uart_driver, &mps_port->port);
> +
> + return 0;
> +}
> +
> +#ifdef CONFIG_OF
> +static const struct of_device_id mps2_match[] = {
> + { .compatible = "arm,mps2-uart", },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, mps2_match);
> +#endif
> +
> +static struct platform_driver mps2_serial_driver = {
> + .probe = mps2_serial_probe,
> + .remove = mps2_serial_remove,
> +
> + .driver = {
> + .name = DRIVER_NAME,
> + .of_match_table = of_match_ptr(mps2_match),
> + },
> +};
> +
> +static int __init mps2_uart_init(void)
> +{
> + int ret;
> +
> + ret = uart_register_driver(&mps2_uart_driver);
> + if (ret)
> + return ret;
> +
> + ret = platform_driver_register(&mps2_serial_driver);
> + if (ret)
> + uart_unregister_driver(&mps2_uart_driver);
> +
> + pr_info("MPS2 UART driver initialized\n");
> +
> + return ret;
> +}
> +module_init(mps2_uart_init);
> +
> +static void __exit mps2_uart_exit(void)
> +{
> + platform_driver_unregister(&mps2_serial_driver);
> + uart_unregister_driver(&mps2_uart_driver);
> +}
> +module_exit(mps2_uart_exit);
module_platform_driver();
And move uart_*register calls to probe/remove.
> +
> +MODULE_AUTHOR("Vladimir Murzin <vladimir.mur...@arm.com>");
> +MODULE_DESCRIPTION("MPS2 UART driver");
> +MODULE_LICENSE("GPL v2");
> +MODULE_ALIAS("platform:" DRIVER_NAME);
> diff --git a/include/uapi/linux/serial_core.h
> b/include/uapi/linux/serial_core.h
> index 93ba148..f097fe9 100644
> --- a/include/uapi/linux/serial_core.h
> +++ b/include/uapi/linux/serial_core.h
> @@ -261,4 +261,7 @@
> /* STM32 USART */
> #define PORT_STM32 113
>
> +/* MPS2 UART */
> +#define PORT_MPS2UART 114
> +
> #endif /* _UAPILINUX_SERIAL_CORE_H */
> --
> 1.7.9.5
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majord...@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
--
With Best Regards,
Andy Shevchenko
--
To unsubscribe from this list: send the line "unsubscribe linux-api" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
