On Tuesday 18 February 2014 15:02:51 Chris Murphy wrote:
> On Feb 18, 2014, at 2:33 PM, Wolfgang Mader <wolfgang_ma...@brain-frog.de>
wrote:
> > Feb 18 13:14:09 deck kernel: ata2.00: failed command: READ DMA
> > Feb 18 13:14:09 deck kernel: ata2.00: cmd
> > c8/00:08:60:f2:30/00:00:00:00:00/e0 tag 0 dma 4096 in
> >
> > res
> > 51/04:08:60:f2:30/00:00:00:00:00/e0
> >
> > Emask 0x1 (device error)
> > Feb 18 13:14:09 deck kernel: ata2.00: status: { DRDY ERR }
> > Feb 18 13:14:09 deck kernel: ata2.00: error: { ABRT }
> > Feb 18 13:14:09 deck kernel: ata2.15: hard resetting link
> > Feb 18 13:14:14 deck kernel: ata2.15: link is slow to respond, please be
> > patient (ready=0)
> > Feb 18 13:14:19 deck kernel: ata2.15: SRST failed (errno=-16)
> > Feb 18 13:14:19 deck kernel: ata2.15: hard resetting link
> > Feb 18 13:14:24 deck kernel: ata2.15: link is slow to respond, please be
> > patient (ready=0)
> > Feb 18 13:14:29 deck kernel: ata2.15: SATA link up 3.0 Gbps (SStatus 123
> > SControl F300)
> > Feb 18 13:14:29 deck kernel:
> > Feb 18 13:14:30 deck kernel: ata2.01: hard resetting link
> > Feb 18 13:14:31 deck kernel: ata2.02: hard resetting link
> > Feb 18 13:14:31 deck kernel: ata2.03: hard resetting link
> > Feb 18 13:14:32 deck kernel: ata2.04: hard resetting link
> > Feb 18 13:14:32 deck kernel: ata2.05: hard resetting link
> > Feb 18 13:14:33 deck kernel: ata2.06: hard resetting link
> > Feb 18 13:14:34 deck kernel: ata2.07: hard resetting link
> > Feb 18 13:14:34 deck kernel: ata2.00: configured for UDMA/133
> > Feb 18 13:14:34 deck kernel: ata2.01: configured for UDMA/133
> > Feb 18 13:14:35 deck kernel: ata2.02: configured for UDMA/133
> > Feb 18 13:14:35 deck kernel: ata2.03: configured for UDMA/133
> > Feb 18 13:14:35 deck kernel: ata2.04: configured for UDMA/133
> > Feb 18 13:14:35 deck kernel: ata2.05: configured for UDMA/133
> > Feb 18 13:14:35 deck kernel: ata2.06: configured for UDMA/133
> > Feb 18 13:14:35 deck kernel: ata2.07: configured for UDMA/133
> > Feb 18 13:14:35 deck kernel: ata2: EH complete
>
> Two things. The full dmesg includes useful information separate from the
> error messages, including the model drive to ata device mapping, and why
> there's a failed read to ATA2.00 yet there's a reset in sequence for
> ata2.01, 2.02, 2.03 and so on. So the entire dmesg would be useful.
You want it, you get it. I attache the full output to this mail, and hope that
the list allows for attachements. Here is a short summary.
The hd enclosure is a Sharkoon 8-Bay which is connected via e-sata. The hds
are mostly Segate Barracude ES.2 (ST31000NSSUN1.0T) and one from Hitachi
(HUA7210SASUN1.0T). All of them are server grade hds and have a device time
out of 30. The hds are sata 1.0 such that they do not feature native command
queuing. I have generally a low read/write performance, around 10MB/sec. I
test the enclosure with a sata 2 disk and got a way better performance, around
70MB/sec. This is why I sticked with the Skarkoon. If the bad performance is
due to bad configuration, I would be happy to fix it. :-)
Now to the dmesg output.
The SRST error you spotted in the logs points to wrong jumper setting
concerning master, slave, cable select. My hds do not have a jumper for this
setting.
The order of the hds is ata2.00->sda ata2.01->sdc etc. The port multiplier
through which all those devices are accessed is ata2.15.
I rebooted the system two times to see if the read error count goes up. Didn't
happen, it sits still at 2.
>
> In any case the actual problem might not be discoverable due to the hard
> resetting. I'm not finding any useful translation, in 5 minute search, for
> SRST. But it makes me suspicious of a configuration problem, like maybe an
> unnecessary jumper setting on a drive or with the enclosure itself. So I'd
> check for that. Also, what model drives are being used? If they are
> consumer drives, they almost certainly have long error recoveries over 30
> minutes. And if the drive is trying to honor the read request for more than
> 30 seconds, the default SCSI block layer will time out and produce messages
> like what we see here. So you probably need to change the SCSI block layer
> timeout. To set the command timer to something else use:
>
> echo <value> /sys/block/<device>/device/timeout
>
> Where value is e.g. 121 since many consumer drives time out at 120 seconds
> this means the kernel will wait 121 seconds before starting its error
> handling (which includes resetting the drive and then the bus).
> > -------end-------
> >
> > This output it repeated several times and than end in this read error
> >
> > [Tue Feb 18 13:15:48 2014] btrfs: bdev /dev/sdb errs: wr 0, rd 2, flush 0,
> > corrupt 0, gen 0
> > [Tue Feb 18 13:15:48 2014] ata2: EH complete
> > [Tue Feb 18 13:15:48 2014] btrfs read error corrected: ino 1 off
> > 29184540672 (dev /dev/sdb sector 3207776)
>
> Well that reads like Btrfs knows what sector had a read problem, without
> corruption being the cause, and corrected it. So the question then is
> whether /dev/sdb is the same as ata2.00. If ata2.00 isn't a drive but is
> the drive enclosure then you've got a different (or additional) problem.
>
>
>
> Chris Murphy--
> To unsubscribe from this list: send the line "unsubscribe linux-btrfs" in
> the body of a message to majord...@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
[Tue Feb 18 12:48:13 2014] Booting Linux on physical CPU 0x0
[Tue Feb 18 12:48:13 2014] Initializing cgroup subsys cpuset
[Tue Feb 18 12:48:13 2014] Initializing cgroup subsys cpu
[Tue Feb 18 12:48:13 2014] Initializing cgroup subsys cpuacct
[Tue Feb 18 12:48:13 2014] Linux version 3.13.3-1-ARCH (nobody@root-armv5-copy)
(gcc version 4.8.2 20131219 (prerelease) (GCC) ) #1 PREEMPT Fri Feb 14 07:05:06
MST 2014
[Tue Feb 18 12:48:13 2014] CPU: Feroceon 88FR131 [56251311] revision 1
(ARMv5TE), cr=00053977
[Tue Feb 18 12:48:13 2014] CPU: VIVT data cache, VIVT instruction cache
[Tue Feb 18 12:48:13 2014] Machine: BUBBA3 Kirkwood based miniserver
[Tue Feb 18 12:48:13 2014] Memory policy: Data cache writeback
[Tue Feb 18 12:48:13 2014] On node 0 totalpages: 131072
[Tue Feb 18 12:48:13 2014] free_area_init_node: node 0, pgdat c0790088,
node_mem_map c0867000
[Tue Feb 18 12:48:13 2014] Normal zone: 1024 pages used for memmap
[Tue Feb 18 12:48:13 2014] Normal zone: 0 pages reserved
[Tue Feb 18 12:48:13 2014] Normal zone: 131072 pages, LIFO batch:31
[Tue Feb 18 12:48:13 2014] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[Tue Feb 18 12:48:13 2014] pcpu-alloc: [0] 0
[Tue Feb 18 12:48:13 2014] Built 1 zonelists in Zone order, mobility grouping
on. Total pages: 130048
[Tue Feb 18 12:48:13 2014] Kernel command line: root=/dev/sda1
console=ttyS0,115200 serial=4773 key=MY9lUnZnipL/8TwjF/qU/X3Gzoc= button=0
[Tue Feb 18 12:48:13 2014] PID hash table entries: 2048 (order: 1, 8192 bytes)
[Tue Feb 18 12:48:13 2014] Dentry cache hash table entries: 65536 (order: 6,
262144 bytes)
[Tue Feb 18 12:48:13 2014] Inode-cache hash table entries: 32768 (order: 5,
131072 bytes)
[Tue Feb 18 12:48:13 2014] Memory: 511144K/524288K available (5487K kernel
code, 333K rwdata, 1660K rodata, 259K init, 828K bss, 13144K reserved)
[Tue Feb 18 12:48:13 2014] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc0702e14 (7148 kB)
.init : 0xc0703000 - 0xc0743c64 ( 260 kB)
.data : 0xc0744000 - 0xc079760c ( 334 kB)
.bss : 0xc079760c - 0xc0866834 ( 829 kB)
[Tue Feb 18 12:48:13 2014] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1,
Nodes=1
[Tue Feb 18 12:48:13 2014] Preemptible hierarchical RCU implementation.
[Tue Feb 18 12:48:13 2014] NR_IRQS:114
[Tue Feb 18 12:48:13 2014] sched_clock: 32 bits at 166MHz, resolution 6ns,
wraps every 25769803770ns
[Tue Feb 18 12:48:13 2014] Console: colour dummy device 80x30
[Tue Feb 18 12:48:33 2014] Calibrating delay loop... 1196.85 BogoMIPS
(lpj=5984256)
[Tue Feb 18 12:48:33 2014] pid_max: default: 32768 minimum: 301
[Tue Feb 18 12:48:33 2014] Security Framework initialized
[Tue Feb 18 12:48:33 2014] AppArmor: AppArmor disabled by boot time parameter
[Tue Feb 18 12:48:33 2014] Mount-cache hash table entries: 512
[Tue Feb 18 12:48:33 2014] Initializing cgroup subsys devices
[Tue Feb 18 12:48:33 2014] Initializing cgroup subsys freezer
[Tue Feb 18 12:48:33 2014] Initializing cgroup subsys net_cls
[Tue Feb 18 12:48:33 2014] Initializing cgroup subsys blkio
[Tue Feb 18 12:48:33 2014] Initializing cgroup subsys bfqio
[Tue Feb 18 12:48:33 2014] Initializing cgroup subsys perf_event
[Tue Feb 18 12:48:33 2014] CPU: Testing write buffer coherency: ok
[Tue Feb 18 12:48:33 2014] Setting up static identity map for 0x538dd8 -
0x538e30
[Tue Feb 18 12:48:33 2014] devtmpfs: initialized
[Tue Feb 18 12:48:33 2014] pinctrl core: initialized pinctrl subsystem
[Tue Feb 18 12:48:33 2014] NET: Registered protocol family 16
[Tue Feb 18 12:48:33 2014] DMA: preallocated 256 KiB pool for atomic coherent
allocations
[Tue Feb 18 12:48:33 2014] cpuidle: using governor ladder
[Tue Feb 18 12:48:33 2014] cpuidle: using governor menu
[Tue Feb 18 12:48:33 2014] Kirkwood: MV88F6281-A1, TCLK=166666667.
[Tue Feb 18 12:48:33 2014] Feroceon L2: Enabling L2
[Tue Feb 18 12:48:33 2014] Feroceon L2: Cache support initialised.
[Tue Feb 18 12:48:33 2014] initial MPP regs: 01112222 43303311 33330044
33003333 00000033 00000000 00000000
[Tue Feb 18 12:48:33 2014] final MPP regs: 11112222 43303311 33330044
33003333 00000033 00000000 00000000
[Tue Feb 18 12:48:33 2014] Kirkwood PCIe port 0: link up
[Tue Feb 18 12:48:33 2014] Kirkwood PCIe port 1: link up
[Tue Feb 18 12:48:33 2014] PCI: bus0 uses PCIe port 0
[Tue Feb 18 12:48:33 2014] PCI host bridge to bus 0000:00
[Tue Feb 18 12:48:33 2014] pci_bus 0000:00: root bus resource [mem
0xe0000000-0xe7ffffff]
[Tue Feb 18 12:48:33 2014] pci_bus 0000:00: root bus resource [io
0x1000-0xffff]
[Tue Feb 18 12:48:33 2014] pci_bus 0000:00: No busn resource found for root
bus, will use [bus 00-ff]
[Tue Feb 18 12:48:33 2014] pci 0000:00:00.0: [11ab:6281] type 00 class 0x058000
[Tue Feb 18 12:48:33 2014] pci 0000:00:00.0: reg 0x10: [mem
0xd0000000-0xd00fffff 64bit pref]
[Tue Feb 18 12:48:33 2014] pci 0000:00:00.0: reg 0x18: [mem
0x00000000-0x1fffffff]
[Tue Feb 18 12:48:33 2014] pci 0000:00:00.0: supports D1 D2
[Tue Feb 18 12:48:33 2014] pci 0000:00:01.0: [168c:002a] type 00 class 0x028000
[Tue Feb 18 12:48:33 2014] pci 0000:00:01.0: reg 0x10: [mem
0x00000000-0x0000ffff 64bit]
[Tue Feb 18 12:48:33 2014] pci 0000:00:01.0: supports D1
[Tue Feb 18 12:48:33 2014] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[Tue Feb 18 12:48:33 2014] PCI: bus0: Fast back to back transfers disabled
[Tue Feb 18 12:48:33 2014] pci_bus 0000:00: busn_res: [bus 00-ff] end is
updated to 00
[Tue Feb 18 12:48:33 2014] PCI: bus1 uses PCIe port 1
[Tue Feb 18 12:48:33 2014] PCI host bridge to bus 0000:01
[Tue Feb 18 12:48:33 2014] pci_bus 0000:01: root bus resource [mem
0xe8000000-0xefffffff]
[Tue Feb 18 12:48:33 2014] pci_bus 0000:01: root bus resource [io
0x10000-0x1ffff]
[Tue Feb 18 12:48:33 2014] pci_bus 0000:01: No busn resource found for root
bus, will use [bus 01-ff]
[Tue Feb 18 12:48:33 2014] PCI: bus1: Fast back to back transfers enabled
[Tue Feb 18 12:48:33 2014] pci_bus 0000:01: busn_res: [bus 01-ff] end is
updated to 01
[Tue Feb 18 12:48:33 2014] pci 0000:00:01.0: BAR 0: assigned [mem
0xe0000000-0xe000ffff 64bit]
[Tue Feb 18 12:48:33 2014] bio: create slab <bio-0> at 0
[Tue Feb 18 12:48:33 2014] vgaarb: loaded
[Tue Feb 18 12:48:33 2014] SCSI subsystem initialized
[Tue Feb 18 12:48:33 2014] libata version 3.00 loaded.
[Tue Feb 18 12:48:33 2014] usbcore: registered new interface driver usbfs
[Tue Feb 18 12:48:33 2014] usbcore: registered new interface driver hub
[Tue Feb 18 12:48:33 2014] usbcore: registered new device driver usb
[Tue Feb 18 12:48:33 2014] pps_core: LinuxPPS API ver. 1 registered
[Tue Feb 18 12:48:33 2014] pps_core: Software ver. 5.3.6 - Copyright 2005-2007
Rodolfo Giometti <giome...@linux.it>
[Tue Feb 18 12:48:33 2014] PTP clock support registered
[Tue Feb 18 12:48:33 2014] Switched to clocksource orion_clocksource
[Tue Feb 18 12:48:33 2014] FS-Cache: Loaded
[Tue Feb 18 12:48:33 2014] NET: Registered protocol family 2
[Tue Feb 18 12:48:33 2014] TCP established hash table entries: 4096 (order: 2,
16384 bytes)
[Tue Feb 18 12:48:33 2014] TCP bind hash table entries: 4096 (order: 2, 16384
bytes)
[Tue Feb 18 12:48:33 2014] TCP: Hash tables configured (established 4096 bind
4096)
[Tue Feb 18 12:48:33 2014] TCP: reno registered
[Tue Feb 18 12:48:33 2014] UDP hash table entries: 256 (order: 0, 4096 bytes)
[Tue Feb 18 12:48:33 2014] UDP-Lite hash table entries: 256 (order: 0, 4096
bytes)
[Tue Feb 18 12:48:33 2014] NET: Registered protocol family 1
[Tue Feb 18 12:48:33 2014] PCI: CLS 32 bytes, default 32
[Tue Feb 18 12:48:33 2014] BUBBA3: driver ver 0.1 (build Feb 14 2014 06:49:19)
loaded
[Tue Feb 18 12:48:33 2014] audit: initializing netlink socket (disabled)
[Tue Feb 18 12:48:33 2014] type=2000 audit(0.120:1): initialized
[Tue Feb 18 12:48:34 2014] VFS: Disk quotas dquot_6.5.2
[Tue Feb 18 12:48:34 2014] Dquot-cache hash table entries: 1024 (order 0, 4096
bytes)
[Tue Feb 18 12:48:34 2014] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[Tue Feb 18 12:48:34 2014] aufs 3.13-20140127
[Tue Feb 18 12:48:34 2014] msgmni has been set to 998
[Tue Feb 18 12:48:34 2014] Block layer SCSI generic (bsg) driver version 0.4
loaded (major 250)
[Tue Feb 18 12:48:34 2014] io scheduler noop registered
[Tue Feb 18 12:48:34 2014] io scheduler deadline registered
[Tue Feb 18 12:48:34 2014] io scheduler cfq registered
[Tue Feb 18 12:48:34 2014] io scheduler bfq registered (default)
[Tue Feb 18 12:48:34 2014] BFQ I/O-scheduler version: v7r1
[Tue Feb 18 12:48:34 2014] mv_xor mv_xor.0: Marvell shared XOR driver
[Tue Feb 18 12:48:34 2014] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[Tue Feb 18 12:48:34 2014] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[Tue Feb 18 12:48:34 2014] mv_xor mv_xor.1: Marvell shared XOR driver
[Tue Feb 18 12:48:34 2014] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[Tue Feb 18 12:48:34 2014] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[Tue Feb 18 12:48:34 2014] Serial: 8250/16550 driver, 2 ports, IRQ sharing
disabled
[Tue Feb 18 12:48:34 2014] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33,
base_baud = 10416666) is a 16550A
[Tue Feb 18 12:48:34 2014] console [ttyS0] enabled
[Tue Feb 18 12:48:34 2014] brd: module loaded
[Tue Feb 18 12:48:34 2014] loop: module loaded
[Tue Feb 18 12:48:34 2014] sata_mv sata_mv.0: version 1.28
[Tue Feb 18 12:48:34 2014] sata_mv sata_mv.0: cannot get optional clkdev
[Tue Feb 18 12:48:34 2014] sata_mv sata_mv.0: slots 32 ports 2
[Tue Feb 18 12:48:34 2014] scsi0 : sata_mv
[Tue Feb 18 12:48:34 2014] scsi1 : sata_mv
[Tue Feb 18 12:48:34 2014] ata1: SATA max UDMA/133 irq 21
[Tue Feb 18 12:48:34 2014] ata2: SATA max UDMA/133 irq 21
[Tue Feb 18 12:48:34 2014] m25p80 spi0.0: m25p16 (2048 Kbytes)
[Tue Feb 18 12:48:34 2014] Creating 3 MTD partitions on "spi_flash":
[Tue Feb 18 12:48:34 2014] 0x000000000000-0x0000000c0000 : "u-boot"
[Tue Feb 18 12:48:34 2014] 0x0000000c0000-0x0000000e0000 : "env"
[Tue Feb 18 12:48:34 2014] 0x0000000e0000-0x000000200000 : "data"
[Tue Feb 18 12:48:34 2014] libphy: orion_mdio_bus: probed
[Tue Feb 18 12:48:34 2014] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver
version 1.4
[Tue Feb 18 12:48:35 2014] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl
F300)
[Tue Feb 18 12:48:35 2014] ata1.00: ATA-8: SEAGATE ST31000NSSUN1.0T 093454YYGN,
SU0D, max UDMA/133
[Tue Feb 18 12:48:35 2014] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ
(depth 31/32)
[Tue Feb 18 12:48:35 2014] ata1.00: configured for UDMA/133
[Tue Feb 18 12:48:35 2014] scsi 0:0:0:0: Direct-Access ATA SEAGATE
ST31000N n/a PQ: 0 ANSI: 5
[Tue Feb 18 12:48:35 2014] sd 0:0:0:0: [sda] 1953525168 512-byte logical
blocks: (1.00 TB/931 GiB)
[Tue Feb 18 12:48:35 2014] sd 0:0:0:0: [sda] Write Protect is off
[Tue Feb 18 12:48:35 2014] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[Tue Feb 18 12:48:35 2014] sd 0:0:0:0: Attached scsi generic sg0 type 0
[Tue Feb 18 12:48:35 2014] sd 0:0:0:0: [sda] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[Tue Feb 18 12:48:35 2014] sda: sda1 sda2 sda3
[Tue Feb 18 12:48:35 2014] sd 0:0:0:0: [sda] Attached SCSI disk
[Tue Feb 18 12:48:35 2014] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0
with MAC address 00:00:00:00:00:00
[Tue Feb 18 12:48:36 2014] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl
F300)
[Tue Feb 18 12:48:36 2014] ata2.15: Port Multiplier 1.2, 0x197b:0x321f r0, 8
ports, feat 0x5/0xf
[Tue Feb 18 12:48:36 2014] ata2.00: hard resetting link
[Tue Feb 18 12:48:37 2014] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0
with MAC address 00:00:00:00:00:00
[Tue Feb 18 12:48:37 2014] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
Driver
[Tue Feb 18 12:48:37 2014] ehci-pci: EHCI PCI platform driver
[Tue Feb 18 12:48:37 2014] ehci-orion: EHCI orion driver
[Tue Feb 18 12:48:37 2014] orion-ehci orion-ehci.0: EHCI Host Controller
[Tue Feb 18 12:48:37 2014] orion-ehci orion-ehci.0: new USB bus registered,
assigned bus number 1
[Tue Feb 18 12:48:37 2014] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[Tue Feb 18 12:48:37 2014] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[Tue Feb 18 12:48:37 2014] hub 1-0:1.0: USB hub found
[Tue Feb 18 12:48:37 2014] hub 1-0:1.0: 1 port detected
[Tue Feb 18 12:48:37 2014] usbcore: registered new interface driver usb-storage
[Tue Feb 18 12:48:37 2014] mousedev: PS/2 mouse device common for all mice
[Tue Feb 18 12:48:37 2014] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[Tue Feb 18 12:48:37 2014] i2c /dev entries driver
[Tue Feb 18 12:48:37 2014] orion_wdt: Initial timeout 25 sec
[Tue Feb 18 12:48:37 2014] sdhci: Secure Digital Host Controller Interface
driver
[Tue Feb 18 12:48:37 2014] sdhci: Copyright(c) Pierre Ossman
[Tue Feb 18 12:48:37 2014] sdhci-pltfm: SDHCI platform and OF driver helper
[Tue Feb 18 12:48:37 2014] ledtrig-cpu: registered to indicate activity on CPUs
[Tue Feb 18 12:48:37 2014] usbcore: registered new interface driver r8712u
[Tue Feb 18 12:48:37 2014] gre: GRE over IPv4 demultiplexor driver
[Tue Feb 18 12:48:37 2014] TCP: cubic registered
[Tue Feb 18 12:48:37 2014] NET: Registered protocol family 17
[Tue Feb 18 12:48:37 2014] Key type dns_resolver registered
[Tue Feb 18 12:48:37 2014] registered taskstats version 1
[Tue Feb 18 12:48:37 2014] usb 1-1: new high-speed USB device number 2 using
orion-ehci
[Tue Feb 18 12:48:37 2014] ata2.01: hard resetting link
[Tue Feb 18 12:48:37 2014] hub 1-1:1.0: USB hub found
[Tue Feb 18 12:48:37 2014] hub 1-1:1.0: 4 ports detected
[Tue Feb 18 12:48:38 2014] ata2.02: hard resetting link
[Tue Feb 18 12:48:38 2014] ata2.03: hard resetting link
[Tue Feb 18 12:48:39 2014] ata2.04: hard resetting link
[Tue Feb 18 12:48:40 2014] ata2.05: hard resetting link
[Tue Feb 18 12:48:40 2014] UKSM: relative memcmp_cost = 2467 hash=234621611
cmp_ret=0.
[Tue Feb 18 12:48:40 2014] console [netcon0] enabled
[Tue Feb 18 12:48:40 2014] netconsole: network logging started
[Tue Feb 18 12:48:40 2014] input: gpio-keys as
/devices/platform/gpio-keys/input/input0
[Tue Feb 18 12:48:40 2014] rtc-mv rtc-mv: setting system clock to 2014-02-18
11:48:27 UTC (1392724107)
[Tue Feb 18 12:48:40 2014] ata2.06: hard resetting link
[Tue Feb 18 12:48:41 2014] ata2.07: hard resetting link
[Tue Feb 18 12:48:42 2014] ata2.00: ATA-7: SEAGATE ST31000NSSUN1.0T 093454YY4D,
0958, max UDMA/133
[Tue Feb 18 12:48:42 2014] ata2.00: 1953525168 sectors, multi 1: LBA48
[Tue Feb 18 12:48:42 2014] ata2.00: configured for UDMA/133
[Tue Feb 18 12:48:42 2014] ata2.01: ATA-7: SEAGATE ST31000NSSUN1.0T 093454YY7W,
0958, max UDMA/133
[Tue Feb 18 12:48:42 2014] ata2.01: 1953525168 sectors, multi 1: LBA48
[Tue Feb 18 12:48:42 2014] ata2.01: configured for UDMA/133
[Tue Feb 18 12:48:42 2014] ata2.02: ATA-7: SEAGATE ST31000NSSUN1.0T 093454YZPT,
0958, max UDMA/133
[Tue Feb 18 12:48:42 2014] ata2.02: 1953525168 sectors, multi 1: LBA48
[Tue Feb 18 12:48:42 2014] ata2.02: configured for UDMA/133
[Tue Feb 18 12:48:42 2014] ata2.03: ATA-7: HITACHI HUA7210SASUN1.0T 0902GB0XRE,
0958, max UDMA/133
[Tue Feb 18 12:48:42 2014] ata2.03: 1953525168 sectors, multi 1: LBA48
[Tue Feb 18 12:48:42 2014] ata2.03: configured for UDMA/133
[Tue Feb 18 12:48:42 2014] ata2.04: ATA-7: SEAGATE ST31000NSSUN1.0T 093454Z0BT,
0958, max UDMA/133
[Tue Feb 18 12:48:42 2014] ata2.04: 1953525168 sectors, multi 1: LBA48
[Tue Feb 18 12:48:42 2014] ata2.04: configured for UDMA/133
[Tue Feb 18 12:48:42 2014] ata2.05: ATA-7: SEAGATE ST31000NSSUN1.0T 091653MEY4,
0958, max UDMA/133
[Tue Feb 18 12:48:42 2014] ata2.05: 1953525168 sectors, multi 1: LBA48
[Tue Feb 18 12:48:42 2014] ata2.05: configured for UDMA/133
[Tue Feb 18 12:48:42 2014] ata2.06: ATA-7: SEAGATE ST31000NSSUN1.0T 093354SA5R,
0958, max UDMA/133
[Tue Feb 18 12:48:42 2014] ata2.06: 1953525168 sectors, multi 1: LBA48
[Tue Feb 18 12:48:42 2014] ata2.06: configured for UDMA/133
[Tue Feb 18 12:48:42 2014] ata2.07: ATA-7: SEAGATE ST31000NSSUN1.0T 0909536218,
0958, max UDMA/133
[Tue Feb 18 12:48:42 2014] ata2.07: 1953525168 sectors, multi 1: LBA48
[Tue Feb 18 12:48:42 2014] ata2.07: configured for UDMA/133
[Tue Feb 18 12:48:42 2014] ata2: EH complete
[Tue Feb 18 12:48:42 2014] scsi 1:0:0:0: Direct-Access ATA SEAGATE
ST31000N 0958 PQ: 0 ANSI: 5
[Tue Feb 18 12:48:42 2014] sd 1:0:0:0: [sdb] 1953525168 512-byte logical
blocks: (1.00 TB/931 GiB)
[Tue Feb 18 12:48:42 2014] sd 1:0:0:0: Attached scsi generic sg1 type 0
[Tue Feb 18 12:48:42 2014] sd 1:0:0:0: [sdb] Write Protect is off
[Tue Feb 18 12:48:42 2014] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[Tue Feb 18 12:48:42 2014] scsi 1:1:0:0: Direct-Access ATA SEAGATE
ST31000N 0958 PQ: 0 ANSI: 5
[Tue Feb 18 12:48:42 2014] sd 1:0:0:0: [sdb] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[Tue Feb 18 12:48:42 2014] sd 1:1:0:0: [sdc] 1953525168 512-byte logical
blocks: (1.00 TB/931 GiB)
[Tue Feb 18 12:48:42 2014] sd 1:1:0:0: Attached scsi generic sg2 type 0
[Tue Feb 18 12:48:42 2014] sd 1:1:0:0: [sdc] Write Protect is off
[Tue Feb 18 12:48:42 2014] scsi 1:2:0:0: Direct-Access ATA SEAGATE
ST31000N 0958 PQ: 0 ANSI: 5
[Tue Feb 18 12:48:42 2014] sdb: unknown partition table
[Tue Feb 18 12:48:42 2014] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[Tue Feb 18 12:48:42 2014] sd 1:1:0:0: [sdc] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[Tue Feb 18 12:48:42 2014] sd 1:0:0:0: [sdb] Attached SCSI disk
[Tue Feb 18 12:48:42 2014] sd 1:2:0:0: [sdd] 1953525168 512-byte logical
blocks: (1.00 TB/931 GiB)
[Tue Feb 18 12:48:42 2014] sd 1:2:0:0: Attached scsi generic sg3 type 0
[Tue Feb 18 12:48:42 2014] sd 1:2:0:0: [sdd] Write Protect is off
[Tue Feb 18 12:48:42 2014] scsi 1:3:0:0: Direct-Access ATA HITACHI
HUA7210S 0958 PQ: 0 ANSI: 5
[Tue Feb 18 12:48:42 2014] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[Tue Feb 18 12:48:42 2014] sd 1:2:0:0: [sdd] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[Tue Feb 18 12:48:42 2014] sd 1:3:0:0: [sde] 1953525168 512-byte logical
blocks: (1.00 TB/931 GiB)
[Tue Feb 18 12:48:42 2014] sdc: unknown partition table
[Tue Feb 18 12:48:42 2014] sd 1:3:0:0: Attached scsi generic sg4 type 0
[Tue Feb 18 12:48:42 2014] sd 1:1:0:0: [sdc] Attached SCSI disk
[Tue Feb 18 12:48:42 2014] sd 1:3:0:0: [sde] Write Protect is off
[Tue Feb 18 12:48:42 2014] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[Tue Feb 18 12:48:42 2014] scsi 1:4:0:0: Direct-Access ATA SEAGATE
ST31000N 0958 PQ: 0 ANSI: 5
[Tue Feb 18 12:48:42 2014] sdd: unknown partition table
[Tue Feb 18 12:48:42 2014] sd 1:3:0:0: [sde] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[Tue Feb 18 12:48:42 2014] sd 1:2:0:0: [sdd] Attached SCSI disk
[Tue Feb 18 12:48:42 2014] sd 1:4:0:0: [sdf] 1953525168 512-byte logical
blocks: (1.00 TB/931 GiB)
[Tue Feb 18 12:48:42 2014] sd 1:4:0:0: Attached scsi generic sg5 type 0
[Tue Feb 18 12:48:42 2014] sd 1:4:0:0: [sdf] Write Protect is off
[Tue Feb 18 12:48:42 2014] sd 1:4:0:0: [sdf] Mode Sense: 00 3a 00 00
[Tue Feb 18 12:48:42 2014] scsi 1:5:0:0: Direct-Access ATA SEAGATE
ST31000N 0958 PQ: 0 ANSI: 5
[Tue Feb 18 12:48:42 2014] sd 1:4:0:0: [sdf] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[Tue Feb 18 12:48:42 2014] sd 1:5:0:0: [sdg] 1953525168 512-byte logical
blocks: (1.00 TB/931 GiB)
[Tue Feb 18 12:48:42 2014] sd 1:5:0:0: Attached scsi generic sg6 type 0
[Tue Feb 18 12:48:42 2014] sd 1:5:0:0: [sdg] Write Protect is off
[Tue Feb 18 12:48:42 2014] sd 1:5:0:0: [sdg] Mode Sense: 00 3a 00 00
[Tue Feb 18 12:48:43 2014] sdf: unknown partition table
[Tue Feb 18 12:48:43 2014] scsi 1:6:0:0: Direct-Access ATA SEAGATE
ST31000N 0958 PQ: 0 ANSI: 5
[Tue Feb 18 12:48:43 2014] sd 1:5:0:0: [sdg] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[Tue Feb 18 12:48:43 2014] sde: sde1
[Tue Feb 18 12:48:43 2014] sd 1:4:0:0: [sdf] Attached SCSI disk
[Tue Feb 18 12:48:43 2014] sd 1:3:0:0: [sde] Attached SCSI disk
[Tue Feb 18 12:48:43 2014] sd 1:6:0:0: [sdh] 1953525168 512-byte logical
blocks: (1.00 TB/931 GiB)
[Tue Feb 18 12:48:43 2014] sd 1:6:0:0: Attached scsi generic sg7 type 0
[Tue Feb 18 12:48:43 2014] sd 1:6:0:0: [sdh] Write Protect is off
[Tue Feb 18 12:48:43 2014] sd 1:6:0:0: [sdh] Mode Sense: 00 3a 00 00
[Tue Feb 18 12:48:43 2014] scsi 1:7:0:0: Direct-Access ATA SEAGATE
ST31000N 0958 PQ: 0 ANSI: 5
[Tue Feb 18 12:48:43 2014] sd 1:6:0:0: [sdh] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[Tue Feb 18 12:48:43 2014] sd 1:7:0:0: [sdi] 1953525168 512-byte logical
blocks: (1.00 TB/931 GiB)
[Tue Feb 18 12:48:43 2014] sd 1:7:0:0: Attached scsi generic sg8 type 0
[Tue Feb 18 12:48:43 2014] sd 1:7:0:0: [sdi] Write Protect is off
[Tue Feb 18 12:48:43 2014] sd 1:7:0:0: [sdi] Mode Sense: 00 3a 00 00
[Tue Feb 18 12:48:43 2014] sdg: unknown partition table
[Tue Feb 18 12:48:43 2014] sd 1:7:0:0: [sdi] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[Tue Feb 18 12:48:43 2014] sd 1:5:0:0: [sdg] Attached SCSI disk
[Tue Feb 18 12:48:43 2014] sdh: sdh1
[Tue Feb 18 12:48:43 2014] sd 1:6:0:0: [sdh] Attached SCSI disk
[Tue Feb 18 12:48:43 2014] sdi: sdi1
[Tue Feb 18 12:48:43 2014] sd 1:7:0:0: [sdi] Attached SCSI disk
[Tue Feb 18 12:48:43 2014] kjournald starting. Commit interval 5 seconds
[Tue Feb 18 12:48:43 2014] EXT3-fs (sda1): using internal journal
[Tue Feb 18 12:48:43 2014] EXT3-fs (sda1): mounted filesystem with writeback
data mode
[Tue Feb 18 12:48:43 2014] VFS: Mounted root (ext3 filesystem) on device 8:1.
[Tue Feb 18 12:48:43 2014] devtmpfs: mounted
[Tue Feb 18 12:48:43 2014] Freeing unused kernel memory: 256K (c0703000 -
c0743000)
[Tue Feb 18 12:48:43 2014] systemd[1]: systemd 208 running in system mode.
(+PAM -LIBWRAP -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[Tue Feb 18 12:48:44 2014] systemd[1]: Inserted module 'autofs4'
[Tue Feb 18 12:48:44 2014] NET: Registered protocol family 10
[Tue Feb 18 12:48:44 2014] systemd[1]: Inserted module 'ipv6'
[Tue Feb 18 12:48:44 2014] systemd[1]: Set hostname to <deck>.
[Tue Feb 18 12:48:44 2014] random: systemd urandom read with 121 bits of
entropy available
[Tue Feb 18 12:48:44 2014] random: nonblocking pool is initialized
[Tue Feb 18 12:48:44 2014] systemd[1]: Cannot add dependency job for unit
cups.socket, ignoring: Unit cups.socket failed to load: No such file or
directory.
[Tue Feb 18 12:48:44 2014] systemd[1]: Cannot add dependency job for unit
cups.path, ignoring: Unit cups.path failed to load: No such file or directory.
[Tue Feb 18 12:48:44 2014] systemd[1]: Cannot add dependency job for unit
display-manager.service, ignoring: Unit display-manager.service failed to load:
No such file or directory.
[Tue Feb 18 12:48:44 2014] systemd[1]: Starting Forward Password Requests to
Wall Directory Watch.
[Tue Feb 18 12:48:44 2014] systemd[1]: Started Forward Password Requests to
Wall Directory Watch.
[Tue Feb 18 12:48:44 2014] systemd[1]: Expecting device dev-ttyS0.device...
[Tue Feb 18 12:48:44 2014] systemd[1]: Expecting device
sys-subsystem-net-devices-eth0.device...
[Tue Feb 18 12:48:44 2014] systemd[1]: Starting Remote File Systems.
[Tue Feb 18 12:48:44 2014] systemd[1]: Reached target Remote File Systems.
[Tue Feb 18 12:48:44 2014] systemd[1]: Starting Delayed Shutdown Socket.
[Tue Feb 18 12:48:44 2014] systemd[1]: Listening on Delayed Shutdown Socket.
[Tue Feb 18 12:48:44 2014] systemd[1]: Starting Device-mapper event daemon
FIFOs.
[Tue Feb 18 12:48:44 2014] systemd[1]: Listening on Device-mapper event daemon
FIFOs.
[Tue Feb 18 12:48:44 2014] systemd[1]: Starting /dev/initctl Compatibility
Named Pipe.
[Tue Feb 18 12:48:44 2014] systemd[1]: Listening on /dev/initctl Compatibility
Named Pipe.
[Tue Feb 18 12:48:45 2014] systemd[1]: Starting Encrypted Volumes.
[Tue Feb 18 12:48:45 2014] systemd[1]: Reached target Encrypted Volumes.
[Tue Feb 18 12:48:45 2014] systemd[1]: Starting Arbitrary Executable File
Formats File System Automount Point.
[Tue Feb 18 12:48:45 2014] systemd[1]: Set up automount Arbitrary Executable
File Formats File System Automount Point.
[Tue Feb 18 12:48:45 2014] systemd[1]: Starting udev Kernel Socket.
[Tue Feb 18 12:48:45 2014] systemd[1]: Listening on udev Kernel Socket.
[Tue Feb 18 12:48:45 2014] systemd[1]: Starting udev Control Socket.
[Tue Feb 18 12:48:45 2014] systemd[1]: Listening on udev Control Socket.
[Tue Feb 18 12:48:45 2014] systemd[1]: Starting Dispatch Password Requests to
Console Directory Watch.
[Tue Feb 18 12:48:45 2014] systemd[1]: Started Dispatch Password Requests to
Console Directory Watch.
[Tue Feb 18 12:48:45 2014] systemd[1]: Starting Paths.
[Tue Feb 18 12:48:45 2014] systemd[1]: Reached target Paths.
[Tue Feb 18 12:48:45 2014] systemd[1]: Starting Journal Socket.
[Tue Feb 18 12:48:45 2014] systemd[1]: Listening on Journal Socket.
[Tue Feb 18 12:48:45 2014] systemd[1]: Mounted Huge Pages File System.
[Tue Feb 18 12:48:45 2014] systemd[1]: Starting Load Kernel Modules...
[Tue Feb 18 12:48:45 2014] systemd[1]: Starting udev Coldplug all Devices...
[Tue Feb 18 12:48:45 2014] systemd[1]: Mounting POSIX Message Queue File
System...
[Tue Feb 18 12:48:45 2014] RPC: Registered named UNIX socket transport module.
[Tue Feb 18 12:48:45 2014] RPC: Registered udp transport module.
[Tue Feb 18 12:48:45 2014] RPC: Registered tcp transport module.
[Tue Feb 18 12:48:45 2014] systemd[1]: Starting Apply Kernel Variables...
[Tue Feb 18 12:48:45 2014] RPC: Registered tcp NFSv4.1 backchannel transport
module.
[Tue Feb 18 12:48:45 2014] systemd[1]: Starting Create list of required static
device nodes for the current kernel...
[Tue Feb 18 12:48:45 2014] systemd[1]: Mounting Debug File System...
[Tue Feb 18 12:48:45 2014] systemd[1]: Started Set Up Additional Binary Formats.
[Tue Feb 18 12:48:45 2014] systemd[1]: Starting Setup Virtual Console...
[Tue Feb 18 12:48:45 2014] systemd[1]: Starting Journal Service...
[Tue Feb 18 12:48:45 2014] systemd[1]: Started Journal Service.
[Tue Feb 18 12:48:45 2014] FS-Cache: Netfs 'nfs' registered for caching
[Tue Feb 18 12:48:45 2014] systemd-journald[70]: Vacuuming done, freed 0 bytes
[Tue Feb 18 12:48:46 2014] systemd-udevd[94]: starting version 208
[Tue Feb 18 12:48:47 2014] cfg80211: Calling CRDA to update world regulatory
domain
[Tue Feb 18 12:48:47 2014] PCI: enabling device 0000:00:01.0 (0140 -> 0142)
[Tue Feb 18 12:48:48 2014] raid6: int32x1 87 MB/s
[Tue Feb 18 12:48:48 2014] raid6: int32x2 133 MB/s
[Tue Feb 18 12:48:48 2014] raid6: int32x4 161 MB/s
[Tue Feb 18 12:48:49 2014] raid6: int32x8 169 MB/s
[Tue Feb 18 12:48:49 2014] raid6: using algorithm int32x8 (169 MB/s)
[Tue Feb 18 12:48:49 2014] raid6: using intx1 recovery algorithm
[Tue Feb 18 12:48:49 2014] xor: measuring software checksum speed
[Tue Feb 18 12:48:49 2014] systemd-journald[70]: Received request to flush
runtime journal from PID 1
[Tue Feb 18 12:48:49 2014] arm4regs : 1090.400 MB/sec
[Tue Feb 18 12:48:49 2014] 8regs : 774.800 MB/sec
[Tue Feb 18 12:48:49 2014] 32regs : 825.600 MB/sec
[Tue Feb 18 12:48:49 2014] xor: using function: arm4regs (1090.400 MB/sec)
[Tue Feb 18 12:48:49 2014] ath: EEPROM regdomain: 0x60
[Tue Feb 18 12:48:49 2014] ath: EEPROM indicates we should expect a direct
regpair map
[Tue Feb 18 12:48:49 2014] ath: Country alpha2 being used: 00
[Tue Feb 18 12:48:49 2014] ath: Regpair used: 0x60
[Tue Feb 18 12:48:49 2014] ieee80211 phy0: Selected rate control algorithm
'minstrel_ht'
[Tue Feb 18 12:48:49 2014] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xe0da0000,
irq=9
[Tue Feb 18 12:48:55 2014] bio: create slab <bio-1> at 1
[Tue Feb 18 12:48:56 2014] Btrfs loaded
[Tue Feb 18 12:48:56 2014] btrfs: device label storage devid 1 transid 2053
/dev/sda3
[Tue Feb 18 12:48:56 2014] btrfs: device label dataPool devid 2 transid 9099
/dev/sdc
[Tue Feb 18 12:48:56 2014] btrfs: device label dataPool devid 5 transid 9099
/dev/sdg
[Tue Feb 18 12:48:56 2014] btrfs: device label dataPool devid 4 transid 9099
/dev/sdf
[Tue Feb 18 12:48:56 2014] btrfs: device label dataPool devid 1 transid 9099
/dev/sdb
[Tue Feb 18 12:48:56 2014] btrfs: device label home devid 1 transid 888
/dev/sda2
[Tue Feb 18 12:48:56 2014] btrfs: device label dataPool devid 3 transid 9099
/dev/sdd
[Tue Feb 18 12:48:56 2014] md: bind<sde1>
[Tue Feb 18 12:48:56 2014] md: bind<sdh1>
[Tue Feb 18 12:48:56 2014] md: bind<sdi1>
[Tue Feb 18 12:48:57 2014] async_tx: api initialized (async)
[Tue Feb 18 12:48:57 2014] md: raid6 personality registered for level 6
[Tue Feb 18 12:48:57 2014] md: raid5 personality registered for level 5
[Tue Feb 18 12:48:57 2014] md: raid4 personality registered for level 4
[Tue Feb 18 12:48:57 2014] md/raid:md0: device sdi1 operational as raid disk 2
[Tue Feb 18 12:48:57 2014] md/raid:md0: device sdh1 operational as raid disk 1
[Tue Feb 18 12:48:57 2014] md/raid:md0: device sde1 operational as raid disk 0
[Tue Feb 18 12:48:57 2014] md/raid:md0: allocated 0kB
[Tue Feb 18 12:48:57 2014] md/raid:md0: raid level 5 active with 3 out of 3
devices, algorithm 2
[Tue Feb 18 12:48:57 2014] RAID conf printout:
[Tue Feb 18 12:48:57 2014] --- level:5 rd:3 wd:3
[Tue Feb 18 12:48:57 2014] disk 0, o:1, dev:sde1
[Tue Feb 18 12:48:57 2014] disk 1, o:1, dev:sdh1
[Tue Feb 18 12:48:57 2014] disk 2, o:1, dev:sdi1
[Tue Feb 18 12:48:57 2014] created bitmap (8 pages) for device md0
[Tue Feb 18 12:48:57 2014] md0: bitmap initialized from disk: read 1 pages, set
0 of 14901 bits
[Tue Feb 18 12:48:57 2014] md0: detected capacity change from 0 to 1999929081856
[Tue Feb 18 12:48:57 2014] md0: unknown partition table
[Tue Feb 18 12:48:57 2014] systemd-udevd[103]: renamed network interface wlan0
to wlp0s1
[Tue Feb 18 12:49:43 2014] mv643xx_eth_port mv643xx_eth_port.0 eth0: link down
[Tue Feb 18 12:49:43 2014] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[Tue Feb 18 12:49:45 2014] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up,
100 Mb/s, full duplex, flow control disabled
[Tue Feb 18 12:49:45 2014] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes
ready
[Tue Feb 18 13:01:31 2014] btrfs: device label dataPool devid 3 transid 9099
/dev/sdd
[Tue Feb 18 13:02:08 2014] btrfs: use lzo compression
[Tue Feb 18 13:02:08 2014] btrfs: disk space caching is enabled
[Tue Feb 18 13:02:09 2014] btrfs: bdev /dev/sdb errs: wr 0, rd 1, flush 0,
corrupt 0, gen 0
[Tue Feb 18 13:13:37 2014] btrfs: device label dataPool devid 3 transid 9103
/dev/sdd
[Tue Feb 18 13:14:29 2014] ata2.15: exception Emask 0x1 SAct 0x0 SErr 0x0
action 0x6
[Tue Feb 18 13:14:29 2014] ata2.15: edma_err_cause=00000084 pp_flags=00000001,
dev error, EDMA self-disable
[Tue Feb 18 13:14:29 2014] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0
action 0x0
[Tue Feb 18 13:14:29 2014] ata2.00: failed command: READ DMA
[Tue Feb 18 13:14:29 2014] ata2.00: cmd c8/00:08:60:f2:30/00:00:00:00:00/e0 tag
0 dma 4096 in
res 51/04:08:60:f2:30/00:00:00:00:00/e0 Emask 0x1 (device error)
[Tue Feb 18 13:14:29 2014] ata2.00: status: { DRDY ERR }
[Tue Feb 18 13:14:29 2014] ata2.00: error: { ABRT }
[Tue Feb 18 13:14:29 2014] ata2.15: hard resetting link
[Tue Feb 18 13:14:34 2014] ata2.15: link is slow to respond, please be patient
(ready=0)
[Tue Feb 18 13:14:39 2014] ata2.15: SRST failed (errno=-16)
[Tue Feb 18 13:14:39 2014] ata2.15: hard resetting link
[Tue Feb 18 13:14:44 2014] ata2.15: link is slow to respond, please be patient
(ready=0)
[Tue Feb 18 13:14:49 2014] ata2.15: SATA link up 3.0 Gbps (SStatus 123 SControl
F300)
[Tue Feb 18 13:14:49 2014] ata2.00: hard resetting link
[Tue Feb 18 13:14:50 2014] ata2.01: hard resetting link
[Tue Feb 18 13:14:50 2014] ata2.02: hard resetting link
[Tue Feb 18 13:14:51 2014] ata2.03: hard resetting link
[Tue Feb 18 13:14:52 2014] ata2.04: hard resetting link
[Tue Feb 18 13:14:52 2014] ata2.05: hard resetting link
[Tue Feb 18 13:14:53 2014] ata2.06: hard resetting link
[Tue Feb 18 13:14:54 2014] ata2.07: hard resetting link
[Tue Feb 18 13:14:54 2014] ata2.00: configured for UDMA/133
[Tue Feb 18 13:14:54 2014] ata2.01: configured for UDMA/133
[Tue Feb 18 13:14:54 2014] ata2.02: configured for UDMA/133
[Tue Feb 18 13:14:54 2014] ata2.03: configured for UDMA/133
[Tue Feb 18 13:14:54 2014] ata2.04: configured for UDMA/133
[Tue Feb 18 13:14:55 2014] ata2.05: configured for UDMA/133
[Tue Feb 18 13:14:55 2014] ata2.06: configured for UDMA/133
[Tue Feb 18 13:14:55 2014] ata2.07: configured for UDMA/133
[Tue Feb 18 13:14:55 2014] ata2: EH complete
[Tue Feb 18 13:14:58 2014] ata2.15: exception Emask 0x1 SAct 0x0 SErr 0x0
action 0x6
[Tue Feb 18 13:14:58 2014] ata2.15: edma_err_cause=00000084 pp_flags=00000001,
dev error, EDMA self-disable
[Tue Feb 18 13:14:58 2014] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0
action 0x0
[Tue Feb 18 13:14:58 2014] ata2.00: failed command: READ DMA
[Tue Feb 18 13:14:58 2014] ata2.00: cmd c8/00:08:60:f2:30/00:00:00:00:00/e0 tag
0 dma 4096 in
res 51/04:08:60:f2:30/00:00:00:00:00/e0 Emask 0x1 (device error)
[Tue Feb 18 13:14:58 2014] ata2.00: status: { DRDY ERR }
[Tue Feb 18 13:14:58 2014] ata2.00: error: { ABRT }
[Tue Feb 18 13:14:58 2014] ata2.15: hard resetting link
[Tue Feb 18 13:14:59 2014] ata2.15: SATA link up 3.0 Gbps (SStatus 123 SControl
F300)
[Tue Feb 18 13:14:59 2014] ata2.00: hard resetting link
[Tue Feb 18 13:15:00 2014] ata2.01: hard resetting link
[Tue Feb 18 13:15:01 2014] ata2.02: hard resetting link
[Tue Feb 18 13:15:01 2014] ata2.03: hard resetting link
[Tue Feb 18 13:15:02 2014] ata2.04: hard resetting link
[Tue Feb 18 13:15:02 2014] ata2.05: hard resetting link
[Tue Feb 18 13:15:03 2014] ata2.06: hard resetting link
[Tue Feb 18 13:15:04 2014] ata2.07: hard resetting link
[Tue Feb 18 13:15:05 2014] ata2.00: configured for UDMA/133
[Tue Feb 18 13:15:05 2014] ata2.01: configured for UDMA/133
[Tue Feb 18 13:15:05 2014] ata2.02: configured for UDMA/133
[Tue Feb 18 13:15:05 2014] ata2.03: configured for UDMA/133
[Tue Feb 18 13:15:05 2014] ata2.04: configured for UDMA/133
[Tue Feb 18 13:15:05 2014] ata2.05: configured for UDMA/133
[Tue Feb 18 13:15:05 2014] ata2.06: configured for UDMA/133
[Tue Feb 18 13:15:05 2014] ata2.07: configured for UDMA/133
[Tue Feb 18 13:15:05 2014] ata2: EH complete
[Tue Feb 18 13:15:09 2014] ata2.15: exception Emask 0x1 SAct 0x0 SErr 0x0
action 0x6
[Tue Feb 18 13:15:09 2014] ata2.15: edma_err_cause=00000084 pp_flags=00000001,
dev error, EDMA self-disable
[Tue Feb 18 13:15:09 2014] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0
action 0x0
[Tue Feb 18 13:15:09 2014] ata2.00: failed command: READ DMA
[Tue Feb 18 13:15:09 2014] ata2.00: cmd c8/00:08:60:f2:30/00:00:00:00:00/e0 tag
0 dma 4096 in
res 51/04:08:60:f2:30/00:00:00:00:00/e0 Emask 0x1 (device error)
[Tue Feb 18 13:15:09 2014] ata2.00: status: { DRDY ERR }
[Tue Feb 18 13:15:09 2014] ata2.00: error: { ABRT }
[Tue Feb 18 13:15:09 2014] ata2.15: hard resetting link
[Tue Feb 18 13:15:10 2014] ata2.15: SATA link up 3.0 Gbps (SStatus 123 SControl
F300)
[Tue Feb 18 13:15:10 2014] ata2.00: hard resetting link
[Tue Feb 18 13:15:11 2014] ata2.01: hard resetting link
[Tue Feb 18 13:15:11 2014] ata2.02: hard resetting link
[Tue Feb 18 13:15:12 2014] ata2.03: hard resetting link
[Tue Feb 18 13:15:12 2014] ata2.04: hard resetting link
[Tue Feb 18 13:15:13 2014] ata2.05: hard resetting link
[Tue Feb 18 13:15:14 2014] ata2.06: hard resetting link
[Tue Feb 18 13:15:15 2014] ata2.07: hard resetting link
[Tue Feb 18 13:15:16 2014] ata2.00: configured for UDMA/133
[Tue Feb 18 13:15:16 2014] ata2.01: configured for UDMA/133
[Tue Feb 18 13:15:16 2014] ata2.02: configured for UDMA/133
[Tue Feb 18 13:15:16 2014] ata2.03: configured for UDMA/133
[Tue Feb 18 13:15:16 2014] ata2.04: configured for UDMA/133
[Tue Feb 18 13:15:16 2014] ata2.05: configured for UDMA/133
[Tue Feb 18 13:15:16 2014] ata2.06: configured for UDMA/133
[Tue Feb 18 13:15:16 2014] ata2.07: configured for UDMA/133
[Tue Feb 18 13:15:16 2014] ata2: EH complete
[Tue Feb 18 13:15:19 2014] ata2.15: exception Emask 0x1 SAct 0x0 SErr 0x0
action 0x6
[Tue Feb 18 13:15:19 2014] ata2.15: edma_err_cause=00000084 pp_flags=00000001,
dev error, EDMA self-disable
[Tue Feb 18 13:15:19 2014] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0
action 0x0
[Tue Feb 18 13:15:19 2014] ata2.00: failed command: READ DMA
[Tue Feb 18 13:15:19 2014] ata2.00: cmd c8/00:08:60:f2:30/00:00:00:00:00/e0 tag
0 dma 4096 in
res 51/04:08:60:f2:30/00:00:00:00:00/e0 Emask 0x1 (device error)
[Tue Feb 18 13:15:19 2014] ata2.00: status: { DRDY ERR }
[Tue Feb 18 13:15:19 2014] ata2.00: error: { ABRT }
[Tue Feb 18 13:15:19 2014] ata2.15: hard resetting link
[Tue Feb 18 13:15:20 2014] ata2.15: SATA link up 3.0 Gbps (SStatus 123 SControl
F300)
[Tue Feb 18 13:15:20 2014] ata2.00: hard resetting link
[Tue Feb 18 13:15:21 2014] ata2.01: hard resetting link
[Tue Feb 18 13:15:22 2014] ata2.02: hard resetting link
[Tue Feb 18 13:15:23 2014] ata2.03: hard resetting link
[Tue Feb 18 13:15:23 2014] ata2.04: hard resetting link
[Tue Feb 18 13:15:24 2014] ata2.05: hard resetting link
[Tue Feb 18 13:15:25 2014] ata2.06: hard resetting link
[Tue Feb 18 13:15:25 2014] ata2.07: hard resetting link
[Tue Feb 18 13:15:26 2014] ata2.00: configured for UDMA/133
[Tue Feb 18 13:15:26 2014] ata2.01: configured for UDMA/133
[Tue Feb 18 13:15:26 2014] ata2.02: configured for UDMA/133
[Tue Feb 18 13:15:26 2014] ata2.03: configured for UDMA/133
[Tue Feb 18 13:15:27 2014] ata2.04: configured for UDMA/133
[Tue Feb 18 13:15:27 2014] ata2.05: configured for UDMA/133
[Tue Feb 18 13:15:27 2014] ata2.06: configured for UDMA/133
[Tue Feb 18 13:15:27 2014] ata2.07: configured for UDMA/133
[Tue Feb 18 13:15:27 2014] ata2: EH complete
[Tue Feb 18 13:15:30 2014] ata2.15: exception Emask 0x1 SAct 0x0 SErr 0x0
action 0x6
[Tue Feb 18 13:15:30 2014] ata2.15: edma_err_cause=00000084 pp_flags=00000001,
dev error, EDMA self-disable
[Tue Feb 18 13:15:30 2014] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0
action 0x0
[Tue Feb 18 13:15:30 2014] ata2.00: failed command: READ DMA
[Tue Feb 18 13:15:30 2014] ata2.00: cmd c8/00:08:60:f2:30/00:00:00:00:00/e0 tag
0 dma 4096 in
res 51/04:08:60:f2:30/00:00:00:00:00/e0 Emask 0x1 (device error)
[Tue Feb 18 13:15:30 2014] ata2.00: status: { DRDY ERR }
[Tue Feb 18 13:15:30 2014] ata2.00: error: { ABRT }
[Tue Feb 18 13:15:30 2014] ata2.15: hard resetting link
[Tue Feb 18 13:15:31 2014] ata2.15: SATA link up 3.0 Gbps (SStatus 123 SControl
F300)
[Tue Feb 18 13:15:31 2014] ata2.00: hard resetting link
[Tue Feb 18 13:15:32 2014] ata2.01: hard resetting link
[Tue Feb 18 13:15:33 2014] ata2.02: hard resetting link
[Tue Feb 18 13:15:33 2014] ata2.03: hard resetting link
[Tue Feb 18 13:15:34 2014] ata2.04: hard resetting link
[Tue Feb 18 13:15:34 2014] ata2.05: hard resetting link
[Tue Feb 18 13:15:35 2014] ata2.06: hard resetting link
[Tue Feb 18 13:15:36 2014] ata2.07: hard resetting link
[Tue Feb 18 13:15:37 2014] ata2.00: configured for UDMA/133
[Tue Feb 18 13:15:37 2014] ata2.01: configured for UDMA/133
[Tue Feb 18 13:15:37 2014] ata2.02: configured for UDMA/133
[Tue Feb 18 13:15:37 2014] ata2.03: configured for UDMA/133
[Tue Feb 18 13:15:37 2014] ata2.04: configured for UDMA/133
[Tue Feb 18 13:15:37 2014] ata2.05: configured for UDMA/133
[Tue Feb 18 13:15:37 2014] ata2.06: configured for UDMA/133
[Tue Feb 18 13:15:37 2014] ata2.07: configured for UDMA/133
[Tue Feb 18 13:15:37 2014] ata2: EH complete
[Tue Feb 18 13:15:40 2014] ata2.15: exception Emask 0x1 SAct 0x0 SErr 0x0
action 0x6
[Tue Feb 18 13:15:40 2014] ata2.15: edma_err_cause=00000084 pp_flags=00000001,
dev error, EDMA self-disable
[Tue Feb 18 13:15:40 2014] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0
action 0x0
[Tue Feb 18 13:15:40 2014] ata2.00: failed command: READ DMA
[Tue Feb 18 13:15:40 2014] ata2.00: cmd c8/00:08:60:f2:30/00:00:00:00:00/e0 tag
0 dma 4096 in
res 51/04:08:60:f2:30/00:00:00:00:00/e0 Emask 0x1 (device error)
[Tue Feb 18 13:15:41 2014] ata2.00: status: { DRDY ERR }
[Tue Feb 18 13:15:41 2014] ata2.00: error: { ABRT }
[Tue Feb 18 13:15:41 2014] ata2.15: hard resetting link
[Tue Feb 18 13:15:42 2014] ata2.15: SATA link up 3.0 Gbps (SStatus 123 SControl
F300)
[Tue Feb 18 13:15:42 2014] ata2.00: hard resetting link
[Tue Feb 18 13:15:42 2014] ata2.01: hard resetting link
[Tue Feb 18 13:15:43 2014] ata2.02: hard resetting link
[Tue Feb 18 13:15:44 2014] ata2.03: hard resetting link
[Tue Feb 18 13:15:44 2014] ata2.04: hard resetting link
[Tue Feb 18 13:15:45 2014] ata2.05: hard resetting link
[Tue Feb 18 13:15:46 2014] ata2.06: hard resetting link
[Tue Feb 18 13:15:47 2014] ata2.07: hard resetting link
[Tue Feb 18 13:15:48 2014] ata2.00: configured for UDMA/133
[Tue Feb 18 13:15:48 2014] ata2.01: configured for UDMA/133
[Tue Feb 18 13:15:48 2014] ata2.02: configured for UDMA/133
[Tue Feb 18 13:15:48 2014] ata2.03: configured for UDMA/133
[Tue Feb 18 13:15:48 2014] ata2.04: configured for UDMA/133
[Tue Feb 18 13:15:48 2014] ata2.05: configured for UDMA/133
[Tue Feb 18 13:15:48 2014] ata2.06: configured for UDMA/133
[Tue Feb 18 13:15:48 2014] ata2.07: configured for UDMA/133
[Tue Feb 18 13:15:48 2014] sd 1:0:0:0: [sdb]
[Tue Feb 18 13:15:48 2014] Result: hostbyte=0x00 driverbyte=0x08
[Tue Feb 18 13:15:48 2014] sd 1:0:0:0: [sdb]
[Tue Feb 18 13:15:48 2014] Sense Key : 0xb [current] [descriptor]
[Tue Feb 18 13:15:48 2014] Descriptor sense data with sense descriptors (in
hex):
[Tue Feb 18 13:15:48 2014] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00
00
[Tue Feb 18 13:15:48 2014] 00 30 f2 60
[Tue Feb 18 13:15:48 2014] sd 1:0:0:0: [sdb]
[Tue Feb 18 13:15:48 2014] ASC=0x0 ASCQ=0x0
[Tue Feb 18 13:15:48 2014] sd 1:0:0:0: [sdb] CDB:
[Tue Feb 18 13:15:48 2014] cdb[0]=0x28: 28 00 00 30 f2 60 00 00 08 00
[Tue Feb 18 13:15:48 2014] end_request: I/O error, dev sdb, sector 3207776
[Tue Feb 18 13:15:48 2014] btrfs: bdev /dev/sdb errs: wr 0, rd 2, flush 0,
corrupt 0, gen 0
[Tue Feb 18 13:15:48 2014] ata2: EH complete
[Tue Feb 18 13:15:48 2014] btrfs read error corrected: ino 1 off 29184540672
(dev /dev/sdb sector 3207776)
[Tue Feb 18 13:29:31 2014] btrfs: device label dataPool devid 3 transid 9104
/dev/sdd
[Tue Feb 18 13:36:16 2014] btrfs: device label dataPool devid 3 transid 9112
/dev/sdd
