(fixed alignment)
------------ Data center systems are generally aligned with the RAS (Reliability, Availability and Serviceability) attributes. When it comes to Storage, RAS applies even more because its matter of trust. In this context, one of the primary area that a typical volume manager should be well tested is, how well RAS attributes are maintained in the context of device failure, and its further reporting. But, identifying a failed device is not a straight forward code. If you look at some statistics performed on failed and returned disks, most of the disks ends up being classified as NTF (No Trouble Found). That is, host failed-and-replaced a disk even before it has actually failed. This is not good for a cost effective setup who would want to stretch the life of an intermittently failing device to its maximum tenure and would want to replace only when it has confirmed dead. Also on the other hand, some of the data center admins would like to mitigate the risk (of low performance at peak of their business productions) of a potential failure, and prefer to pro-actively replace the disk at their low business/workload hours, or they may choose to replace a device even for read errors (mainly due to performance reasons). In short a large variant of real MTF (Mean Time to Failure) for the devices across the industries/users. Consideration: - Have user-tunable to support different context of usages, which should be applied on top of a set of disk IO errors, and its out come will be to know if the disk can be failed. - Distinguish real disk failure (failed state) VS IO errors due to intermittent transport errors (offline state). (I am not sure how to do that yet, basically in some means, block layer could help?, RFC ?). - A sysfs offline interface, so as to udev update the kernel, when disk is pulled out. - Because even to fail a device it depends on the user requirements, btrfs IO completion threads instead of directly reacting on an IO error, it will continue to just report the IO error into device error statistics, and a spooler up on errors will apply user/system criticalness as provided by the user on the top, which will decide if the device has to be marked as failed OR if it can continue to be in online. - A FS load pattern (mostly outside of btrfs-kernel or with in btrfs- kernel) may pick the right time to replace the failed device, or to run other FS maintenance activities (balance, scrub) automatically. - Sysfs will help user land scripts which may want to bring device to offline or failed. Device State flow: A device in the btrfs kernel can be in any one of following state: Online A normal healthy device Missing Device wasn't found that the time of mount OR device scan. Offline (disappeared) Device was present at some point in time after the FS was mounted, however offlined by user or block layer or hot unplug or device experienced transport error. Basically due to any error other than media error. The device in offline state are not candidate for the replace. Since still there is a hope that device may be restored to online at some point in time, by user or transport-layer error recovery. For device pulled out, there will be udev script which will call offline through sysfs. In the long run, we would also need to know the block layer to distinguish from the transient write errors like writes failing due to transport error, vs write errors which are confirmed as target-device/device-media failure. Failed Device has confirmed a write/flush failure for at least a block. (In general the disk/storage FW will try to relocate the bad block on write, it happens automatically and transparent even to the block layer. Further there might have been few retry from the block layer. And here btrfs assumes that such an attempt has also failed). Or it might set device as failed for extensive read errors if the user tuned profile demands it. A btrfs pool can be in one of the state: Online: All the chunks are as configured. Degraded: One or more logical-chunks does not meet the redundancy level that user requested / configured. Failed: One or more logical-chunk is incomplete. FS will be in a RO mode Or panic -dump as configured. Flow diagram (also include pool states BTRFS_POOL_STATE_xx along with device state BTRFS_DEVICE_STATE_xx): [1] BTRFS_DEVICE_STATE_ONLINE, BTRFS_POOL_STATE_ONLINE | | V new IO error | | V check with block layer to know if confirmed media/target:- failed or fix-able transport issue:- offline. and apply user config. can be ignored ? --------------yes->[1] | |no _______offline__________/\______failed________ | | | | V V (eg: transport issue [*], disk is good) (eg: write media error) | | | | V V BTRFS_DEVICE_STATE_OFFLINE BTRFS_DEVICE_STATE_FAILED | | | | |______________________ _____________________| \/ | Missing chunk ? --NO--> goto [1] | | Tolerable? -NO-> FS ERROR. RO. BTRFS_POOL_STATE_FAILED->remount? | |yes V BTRFS_POOL_STATE_DEGRADED --> rebalance -> [1] | ______offline___________|____failed_________ | | | check priority | | | | | hot spare ? | replace --> goto [1] | | | | no | | | spare-add (user/sys notify issue is fixed, (manual-replace/dev-delete) trigger scrub/balance) | |______________________ ___________________| \/ | V [1] Code status: Part-1: Provided device transitions from online to failed/offline, hot spare and auto replace. [PATCH 00/15] btrfs: Hot spare and Auto replace Next, . Add sysfs part on top of [PATCH] btrfs: Introduce device pool sysfs attributes . POOL_STATE flow and reporting . Device transactions from Offline to Online . Btrfs-progs mainly to show device and pool states . Apply user tolerance level to the IO errors ---------- Thanks, Anand -- To unsubscribe from this list: send the line "unsubscribe linux-btrfs" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html