Let me check my system at home tomight and I will get back to you.. Ill
check and see how they compare. ( /etc/inittab )
Cheers,
*~*~*~*~*~*~*~*~*~*~*
Tony Hernandez
*NIX, MCP, A+
Intellon Corporation
*~*~*~*~*~*~*~*~*~*~*
# -----Original Message-----
# From: [EMAIL PROTECTED]
# [mailto:[EMAIL PROTECTED]]On Behalf Of George R.
# Kasica
# Sent: Wednesday, October 27, 1999 6:32 PM
# To: Tony Hernandez
# Cc: [EMAIL PROTECTED]
# Subject: Re: How to stop graphical boot up screen in Caldera Openlinux
# 2.
#
#
# On Wed, 27 Oct 1999 11:33:37 -0400, you wrote:
#
# >I'm not sure what the message line is or even the install
# line. I have
# >neither of these in my /etc/lilo.conf ofcourse I dont use
# Caldera .. <
# >Slackware ! > I bet these may be the culprit. if you change
# anything in this
# >file just re-run lilo :
# ># lilo
# >
# >and reboot .. I couldn't Imagine it being anywhere else ...
# >
# >
# Well, that didn't help....its waits at the boot: prompt (which is new
# and good) but once you hit Enter or it times out, you're back to the
# $%&$ graphic screen....I'm enclosing lilo.conf and inittab here...I
# was wondering about the s0 line with the booterd and such...could that
# have something to do with it??
#
# George
#
#
#
# [root@eagle /etc]# more lilo.conf
# #
# # general section
# #
# boot = /dev/hda1
# # install = /boot/boot.b
# # message = /boot/message
# prompt
#
# # wait 30 seconds (300 10ths) for user to select the entry to load
# timeout = 300
#
# #
# # default entry
# #
#
# # image = /boot/vmlinuz-2.2.5-modular
# image = /vmlinuz
# label = linux
# root = /dev/hda1
# vga = 274
# read-only
# append = "debug=2"
#
#
# #
# # additional entries
# #
#
# image = /boot/vmlinuz-2.2.5-modular
# label = linux-old
# root = /dev/hda1
# vga = 274
# read-only
# append = "debug=2"
#
#
#
# [root@eagle /etc]# more inittab
# #
# # inittab This file describes how the INIT process should set up
# # the system in a certain run-level.
# #
# # Author: Miquel van Smoorenburg,
# <[EMAIL PROTECTED]>
# # Modified for RHS Linux by Marc Ewing and Donnie Barnes
# # Modified for COL by Raymund Will
# #
#
# # The runlevels used by COL are:
# # 0 - halt (Do NOT set initdefault to this)
# # 1 - Single user mode (including initialisation of network
# interfaces,
# # if you do have networking)
# # 2 - Multiuser, (without NFS-Server und some such)
# # (basically the same as 3, if you do not have networking)
# # 3 - Full multiuser mode
# # 4 - unused
# # (should be equal to 3, for now)
# # 5 - X11
# # 6 - reboot (Do NOT set initdefault to this)
#
# #
# # Default runlevel.
# id:5:initdefault:
#
# # System initialization.
# s0::sysinit:/bin/bash -c 'C=/sbin/booterd; [ -x $C ] && $C'
# si::sysinit:/bin/bash -c 'C=/etc/rc.d/rc.modules; [ -x $C ] && $C
# default'
# s2::sysinit:/bin/bash -c 'C=/etc/rc.d/rc.serial; [ -x $C ] && $C'
# bw::bootwait:/etc/rc.d/rc.boot
#
# # What to do in single-user mode.
# ~1:S:wait:/etc/rc.d/rc 1
# ~~:S:wait:/sbin/sulogin
#
# l0:0:wait:/etc/rc.d/rc 0
# l1:1:wait:/etc/rc.d/rc 1
# l2:2:wait:/etc/rc.d/rc 2
# l3:3:wait:/etc/rc.d/rc 3
# l4:4:wait:/etc/rc.d/rc 4
# l5:5:wait:/etc/rc.d/rc 5
# l6:6:wait:/etc/rc.d/rc 6
# # Normally not reached, but fallthrough in case of emergency.
# z6:6:respawn:/sbin/sulogin
#
# # Trap CTRL-ALT-DELETE
# ca:12345:ctrlaltdel:/sbin/shutdown -t3 -r now
#
# # Action on special keypress (ALT-UpArrow).
# kb::kbrequest:/bin/echo "Keyboard Request--edit /etc/inittab to let
# this work."
#
# # When our UPS tells us power has failed, assume we have a few minutes
# # of power left. Schedule a shutdown for 2 minutes from now.
# # This does, of course, assume you have powerd installed and your
# # UPS connected and working correctly.
# pf::powerfail:/sbin/shutdown -h +5 "Power Failure; System Shutting
# Down"
#
# # If battery is fading fast -- we hurry...
# p1::powerfailnow:/sbin/shutdown -c 2> /dev/null
# p2::powerfailnow:/sbin/shutdown -h now "Battery Low..."
#
# # If power was restored before the shutdown kicked in, cancel it.
# po:12345:powerokwait:/sbin/shutdown -c "Power Restored; Shutdown
# Cancelled"
#
#
# # Run gettys in standard runlevels
# 1:12345:respawn:/sbin/getty tty1 VC linux
# 2:2345:respawn:/sbin/getty tty2 VC linux
# 3:2345:respawn:/sbin/getty tty3 VC linux
# 4:2345:respawn:/sbin/getty tty4 VC linux
# 5:2345:respawn:/sbin/getty tty5 VC linux
# 6:2345:respawn:/sbin/getty tty6 VC linux
#
# # Run kdm in runlevel 5
# kdm:5:respawn:/opt/kde/bin/kdm -nodaemon > /var/log/kdm 2>&1
#
# George, MR. Tibbs & The Beast Kasica
# Waukesha, WI USA
# [EMAIL PROTECTED]
# http://www.netwrx1.com
# ICQ #12862186
#
# Zz
# zZ
# |\ z _,,,---,,_
# /,`.-'`' _ ;-;;,_
# |,4- ) )-,_..;\ ( `'_'
# '---''(_/--' `-'\_)
#
