On Sun, Jan 11, 2015 at 11:48:08PM -0500, Timothy McCaffrey wrote:
> These patches fix the RFC4106 implementation in the aesni-intel module so it
> supports 192 & 256 bit keys.
>
> Since the AVX support that was added to this module also only supports 128
> bit keys,
> and this patch only affects the SSE implementation, changes were also made to
> use the SSE version if key sizes other than 128 are specified.
>
> RFC4106 specifies that 192 & 256 bit keys must be supported (section 8.4).
>
> Also, this should fix Strongswan issue 341 where the aesni module needs to be
> unloaded if 256 bit keys are used:
>
> http://wiki.strongswan.org/issues/341
>
> This patch has been tested with Sandy Bridge and Haswell processors. With 128
> bit keys and input buffers > 512 bytes a slight performance degradation was
> noticed (~1%). For input buffers of less than 512 bytes there was no
> performance impact. Compared to 128 bit keys, 256 bit key size performance
> is approx. .5 cycles per byte slower on Sandy Bridge, and .37 cycles per
> byte slower on Haswell (vs. SSE code).
>
> This patch has also been tested with StrongSwan IPSec connections where it
> worked correctly.
>
> I created this diff from a git clone of crypto-2.6.git.
>
> Any questions, please feel free to contact me.
>
> Signed off by: timothy.mccaff...@unisys.com
Here's an unborked version that applies cleanly to linus' master right
now. Somehow, tons of extra spaces made their way into the original
(re-)submission, I just stripped them out (and fixed up a few extra
trailing spaces and spaces before tabs).
Signed-off-by: Jarod Wilson <ja...@redhat.com>
---
diff --git a/arch/x86/crypto/aesni-intel_asm.S
b/arch/x86/crypto/aesni-intel_asm.S
index 477e9d7..6bd2c6c 100644
--- a/arch/x86/crypto/aesni-intel_asm.S
+++ b/arch/x86/crypto/aesni-intel_asm.S
@@ -32,12 +32,23 @@
#include <linux/linkage.h>
#include <asm/inst.h>
+/*
+ * The following macros are used to move an (un)aligned 16 byte value to/from
+ * an XMM register. This can done for either FP or integer values, for FP use
+ * movaps (move aligned packed single) or integer use movdqa (move double quad
+ * aligned). It doesn't make a performance difference which instruction is
used
+ * since Nehalem (original Core i7) was released. However, the movaps is a
byte
+ * shorter, so that is the one we'll use for now. (same for unaligned).
+ */
+#define MOVADQ movaps
+#define MOVUDQ movups
+
#ifdef __x86_64__
+
.data
.align 16
.Lgf128mul_x_ble_mask:
.octa 0x00000000000000010000000000000087
-
POLY: .octa 0xC2000000000000000000000000000001
TWOONE: .octa 0x00000001000000000000000000000001
@@ -89,6 +100,7 @@ enc: .octa 0x2
#define arg8 STACK_OFFSET+16(%r14)
#define arg9 STACK_OFFSET+24(%r14)
#define arg10 STACK_OFFSET+32(%r14)
+#define keysize 2*15*16(%arg1)
#endif
@@ -213,10 +225,12 @@ enc: .octa 0x2
.macro INITIAL_BLOCKS_DEC num_initial_blocks TMP1 TMP2 TMP3 TMP4 TMP5 XMM0
XMM1 \
XMM2 XMM3 XMM4 XMMDst TMP6 TMP7 i i_seq operation
+ MOVADQ SHUF_MASK(%rip), %xmm14
mov arg7, %r10 # %r10 = AAD
mov arg8, %r12 # %r12 = aadLen
mov %r12, %r11
pxor %xmm\i, %xmm\i
+
_get_AAD_loop\num_initial_blocks\operation:
movd (%r10), \TMP1
pslldq $12, \TMP1
@@ -225,16 +239,18 @@ _get_AAD_loop\num_initial_blocks\operation:
add $4, %r10
sub $4, %r12
jne _get_AAD_loop\num_initial_blocks\operation
+
cmp $16, %r11
je _get_AAD_loop2_done\num_initial_blocks\operation
+
mov $16, %r12
_get_AAD_loop2\num_initial_blocks\operation:
psrldq $4, %xmm\i
sub $4, %r12
cmp %r11, %r12
jne _get_AAD_loop2\num_initial_blocks\operation
+
_get_AAD_loop2_done\num_initial_blocks\operation:
- movdqa SHUF_MASK(%rip), %xmm14
PSHUFB_XMM %xmm14, %xmm\i # byte-reflect the AAD data
xor %r11, %r11 # initialise the data pointer offset as zero
@@ -243,59 +259,34 @@ _get_AAD_loop2_done\num_initial_blocks\operation:
mov %arg5, %rax # %rax = *Y0
movdqu (%rax), \XMM0 # XMM0 = Y0
- movdqa SHUF_MASK(%rip), %xmm14
PSHUFB_XMM %xmm14, \XMM0
.if (\i == 5) || (\i == 6) || (\i == 7)
+ MOVADQ ONE(%RIP),\TMP1
+ MOVADQ (%arg1),\TMP2
.irpc index, \i_seq
- paddd ONE(%rip), \XMM0 # INCR Y0
+ paddd \TMP1, \XMM0 # INCR Y0
movdqa \XMM0, %xmm\index
- movdqa SHUF_MASK(%rip), %xmm14
PSHUFB_XMM %xmm14, %xmm\index # perform a 16 byte swap
-
-.endr
-.irpc index, \i_seq
- pxor 16*0(%arg1), %xmm\index
-.endr
-.irpc index, \i_seq
- movaps 0x10(%rdi), \TMP1
- AESENC \TMP1, %xmm\index # Round 1
-.endr
-.irpc index, \i_seq
- movaps 0x20(%arg1), \TMP1
- AESENC \TMP1, %xmm\index # Round 2
-.endr
-.irpc index, \i_seq
- movaps 0x30(%arg1), \TMP1
- AESENC \TMP1, %xmm\index # Round 2
-.endr
-.irpc index, \i_seq
- movaps 0x40(%arg1), \TMP1
- AESENC \TMP1, %xmm\index # Round 2
-.endr
-.irpc index, \i_seq
- movaps 0x50(%arg1), \TMP1
- AESENC \TMP1, %xmm\index # Round 2
-.endr
-.irpc index, \i_seq
- movaps 0x60(%arg1), \TMP1
- AESENC \TMP1, %xmm\index # Round 2
+ pxor \TMP2, %xmm\index
.endr
-.irpc index, \i_seq
- movaps 0x70(%arg1), \TMP1
- AESENC \TMP1, %xmm\index # Round 2
-.endr
-.irpc index, \i_seq
- movaps 0x80(%arg1), \TMP1
- AESENC \TMP1, %xmm\index # Round 2
-.endr
-.irpc index, \i_seq
- movaps 0x90(%arg1), \TMP1
- AESENC \TMP1, %xmm\index # Round 2
+ lea 0x10(%arg1),%r10
+ mov keysize,%eax
+ shr $2,%eax # 128->4, 192->6, 256->8
+ add $5,%eax # 128->9, 192->11, 256->13
+
+aes_loop_initial_dec\num_initial_blocks:
+ MOVADQ (%r10),\TMP1
+.irpc index, \i_seq
+ AESENC \TMP1, %xmm\index
.endr
+ add $16,%r10
+ sub $1,%eax
+ jnz aes_loop_initial_dec\num_initial_blocks
+
+ MOVADQ (%r10), \TMP1
.irpc index, \i_seq
- movaps 0xa0(%arg1), \TMP1
- AESENCLAST \TMP1, %xmm\index # Round 10
+ AESENCLAST \TMP1, %xmm\index # Last Round
.endr
.irpc index, \i_seq
movdqu (%arg3 , %r11, 1), \TMP1
@@ -305,10 +296,8 @@ _get_AAD_loop2_done\num_initial_blocks\operation:
add $16, %r11
movdqa \TMP1, %xmm\index
- movdqa SHUF_MASK(%rip), %xmm14
PSHUFB_XMM %xmm14, %xmm\index
-
- # prepare plaintext/ciphertext for GHASH computation
+ # prepare plaintext/ciphertext for GHASH computation
.endr
.endif
GHASH_MUL %xmm\i, \TMP3, \TMP1, \TMP2, \TMP4, \TMP5, \XMM1
@@ -338,30 +327,28 @@ _get_AAD_loop2_done\num_initial_blocks\operation:
* Precomputations for HashKey parallel with encryption of first 4 blocks.
* Haskey_i_k holds XORed values of the low and high parts of the Haskey_i
*/
- paddd ONE(%rip), \XMM0 # INCR Y0
- movdqa \XMM0, \XMM1
- movdqa SHUF_MASK(%rip), %xmm14
+ MOVADQ ONE(%rip), \TMP1
+ paddd \TMP1, \XMM0 # INCR Y0
+ MOVADQ \XMM0, \XMM1
PSHUFB_XMM %xmm14, \XMM1 # perform a 16 byte swap
- paddd ONE(%rip), \XMM0 # INCR Y0
- movdqa \XMM0, \XMM2
- movdqa SHUF_MASK(%rip), %xmm14
+ paddd \TMP1, \XMM0 # INCR Y0
+ MOVADQ \XMM0, \XMM2
PSHUFB_XMM %xmm14, \XMM2 # perform a 16 byte swap
- paddd ONE(%rip), \XMM0 # INCR Y0
- movdqa \XMM0, \XMM3
- movdqa SHUF_MASK(%rip), %xmm14
+ paddd \TMP1, \XMM0 # INCR Y0
+ MOVADQ \XMM0, \XMM3
PSHUFB_XMM %xmm14, \XMM3 # perform a 16 byte swap
- paddd ONE(%rip), \XMM0 # INCR Y0
- movdqa \XMM0, \XMM4
- movdqa SHUF_MASK(%rip), %xmm14
+ paddd \TMP1, \XMM0 # INCR Y0
+ MOVADQ \XMM0, \XMM4
PSHUFB_XMM %xmm14, \XMM4 # perform a 16 byte swap
- pxor 16*0(%arg1), \XMM1
- pxor 16*0(%arg1), \XMM2
- pxor 16*0(%arg1), \XMM3
- pxor 16*0(%arg1), \XMM4
+ MOVADQ 0(%arg1),\TMP1
+ pxor \TMP1, \XMM1
+ pxor \TMP1, \XMM2
+ pxor \TMP1, \XMM3
+ pxor \TMP1, \XMM4
movdqa \TMP3, \TMP5
pshufd $78, \TMP3, \TMP1
pxor \TMP3, \TMP1
@@ -399,7 +386,23 @@ _get_AAD_loop2_done\num_initial_blocks\operation:
pshufd $78, \TMP5, \TMP1
pxor \TMP5, \TMP1
movdqa \TMP1, HashKey_4_k(%rsp)
- movaps 0xa0(%arg1), \TMP2
+ lea 0xa0(%arg1),%r10
+ mov keysize,%eax
+ shr $2,%eax # 128->4, 192->6, 256->8
+ sub $4,%eax # 128->0, 192->2, 256->4
+ jz aes_loop_pre_dec_done\num_initial_blocks
+
+aes_loop_pre_dec\num_initial_blocks:
+ MOVADQ (%r10),\TMP2
+.irpc index, 1234
+ AESENC \TMP2, %xmm\index
+.endr
+ add $16,%r10
+ sub $1,%eax
+ jnz aes_loop_pre_dec\num_initial_blocks
+
+aes_loop_pre_dec_done\num_initial_blocks:
+ MOVADQ (%r10), \TMP2
AESENCLAST \TMP2, \XMM1
AESENCLAST \TMP2, \XMM2
AESENCLAST \TMP2, \XMM3
@@ -421,15 +424,11 @@ _get_AAD_loop2_done\num_initial_blocks\operation:
movdqu \XMM4, 16*3(%arg2 , %r11 , 1)
movdqa \TMP1, \XMM4
add $64, %r11
- movdqa SHUF_MASK(%rip), %xmm14
PSHUFB_XMM %xmm14, \XMM1 # perform a 16 byte swap
pxor \XMMDst, \XMM1
# combine GHASHed value with the corresponding ciphertext
- movdqa SHUF_MASK(%rip), %xmm14
PSHUFB_XMM %xmm14, \XMM2 # perform a 16 byte swap
- movdqa SHUF_MASK(%rip), %xmm14
PSHUFB_XMM %xmm14, \XMM3 # perform a 16 byte swap
- movdqa SHUF_MASK(%rip), %xmm14
PSHUFB_XMM %xmm14, \XMM4 # perform a 16 byte swap
_initial_blocks_done\num_initial_blocks\operation:
@@ -451,6 +450,7 @@ _initial_blocks_done\num_initial_blocks\operation:
.macro INITIAL_BLOCKS_ENC num_initial_blocks TMP1 TMP2 TMP3 TMP4 TMP5 XMM0
XMM1 \
XMM2 XMM3 XMM4 XMMDst TMP6 TMP7 i i_seq operation
+ MOVADQ SHUF_MASK(%rip), %xmm14
mov arg7, %r10 # %r10 = AAD
mov arg8, %r12 # %r12 = aadLen
mov %r12, %r11
@@ -472,7 +472,6 @@ _get_AAD_loop2\num_initial_blocks\operation:
cmp %r11, %r12
jne _get_AAD_loop2\num_initial_blocks\operation
_get_AAD_loop2_done\num_initial_blocks\operation:
- movdqa SHUF_MASK(%rip), %xmm14
PSHUFB_XMM %xmm14, %xmm\i # byte-reflect the AAD data
xor %r11, %r11 # initialise the data pointer offset as zero
@@ -481,59 +480,35 @@ _get_AAD_loop2_done\num_initial_blocks\operation:
mov %arg5, %rax # %rax = *Y0
movdqu (%rax), \XMM0 # XMM0 = Y0
- movdqa SHUF_MASK(%rip), %xmm14
PSHUFB_XMM %xmm14, \XMM0
.if (\i == 5) || (\i == 6) || (\i == 7)
-.irpc index, \i_seq
- paddd ONE(%rip), \XMM0 # INCR Y0
- movdqa \XMM0, %xmm\index
- movdqa SHUF_MASK(%rip), %xmm14
- PSHUFB_XMM %xmm14, %xmm\index # perform a 16 byte swap
-.endr
-.irpc index, \i_seq
- pxor 16*0(%arg1), %xmm\index
-.endr
-.irpc index, \i_seq
- movaps 0x10(%rdi), \TMP1
- AESENC \TMP1, %xmm\index # Round 1
-.endr
-.irpc index, \i_seq
- movaps 0x20(%arg1), \TMP1
- AESENC \TMP1, %xmm\index # Round 2
-.endr
+ MOVADQ ONE(%RIP),\TMP1
+ MOVADQ 0(%arg1),\TMP2
.irpc index, \i_seq
- movaps 0x30(%arg1), \TMP1
- AESENC \TMP1, %xmm\index # Round 2
+ paddd \TMP1, \XMM0 # INCR Y0
+ MOVADQ \XMM0, %xmm\index
+ PSHUFB_XMM %xmm14, %xmm\index # perform a 16 byte swap
+ pxor \TMP2, %xmm\index
.endr
-.irpc index, \i_seq
- movaps 0x40(%arg1), \TMP1
- AESENC \TMP1, %xmm\index # Round 2
-.endr
-.irpc index, \i_seq
- movaps 0x50(%arg1), \TMP1
- AESENC \TMP1, %xmm\index # Round 2
-.endr
-.irpc index, \i_seq
- movaps 0x60(%arg1), \TMP1
- AESENC \TMP1, %xmm\index # Round 2
-.endr
-.irpc index, \i_seq
- movaps 0x70(%arg1), \TMP1
- AESENC \TMP1, %xmm\index # Round 2
-.endr
-.irpc index, \i_seq
- movaps 0x80(%arg1), \TMP1
- AESENC \TMP1, %xmm\index # Round 2
-.endr
-.irpc index, \i_seq
- movaps 0x90(%arg1), \TMP1
- AESENC \TMP1, %xmm\index # Round 2
+ lea 0x10(%arg1),%r10
+ mov keysize,%eax
+ shr $2,%eax # 128->4, 192->6, 256->8
+ add $5,%eax # 128->9, 192->11, 256->13
+
+aes_loop_initial_enc\num_initial_blocks:
+ MOVADQ (%r10),\TMP1
+.irpc index, \i_seq
+ AESENC \TMP1, %xmm\index
.endr
+ add $16,%r10
+ sub $1,%eax
+ jnz aes_loop_initial_enc\num_initial_blocks
+
+ MOVADQ (%r10), \TMP1
.irpc index, \i_seq
- movaps 0xa0(%arg1), \TMP1
- AESENCLAST \TMP1, %xmm\index # Round 10
+ AESENCLAST \TMP1, %xmm\index # Last Round
.endr
.irpc index, \i_seq
movdqu (%arg3 , %r11, 1), \TMP1
@@ -541,8 +516,6 @@ _get_AAD_loop2_done\num_initial_blocks\operation:
movdqu %xmm\index, (%arg2 , %r11, 1)
# write back plaintext/ciphertext for num_initial_blocks
add $16, %r11
-
- movdqa SHUF_MASK(%rip), %xmm14
PSHUFB_XMM %xmm14, %xmm\index
# prepare plaintext/ciphertext for GHASH computation
@@ -575,30 +548,28 @@ _get_AAD_loop2_done\num_initial_blocks\operation:
* Precomputations for HashKey parallel with encryption of first 4 blocks.
* Haskey_i_k holds XORed values of the low and high parts of the Haskey_i
*/
- paddd ONE(%rip), \XMM0 # INCR Y0
- movdqa \XMM0, \XMM1
- movdqa SHUF_MASK(%rip), %xmm14
+ MOVADQ ONE(%RIP),\TMP1
+ paddd \TMP1, \XMM0 # INCR Y0
+ MOVADQ \XMM0, \XMM1
PSHUFB_XMM %xmm14, \XMM1 # perform a 16 byte swap
- paddd ONE(%rip), \XMM0 # INCR Y0
- movdqa \XMM0, \XMM2
- movdqa SHUF_MASK(%rip), %xmm14
+ paddd \TMP1, \XMM0 # INCR Y0
+ MOVADQ \XMM0, \XMM2
PSHUFB_XMM %xmm14, \XMM2 # perform a 16 byte swap
- paddd ONE(%rip), \XMM0 # INCR Y0
- movdqa \XMM0, \XMM3
- movdqa SHUF_MASK(%rip), %xmm14
+ paddd \TMP1, \XMM0 # INCR Y0
+ MOVADQ \XMM0, \XMM3
PSHUFB_XMM %xmm14, \XMM3 # perform a 16 byte swap
- paddd ONE(%rip), \XMM0 # INCR Y0
- movdqa \XMM0, \XMM4
- movdqa SHUF_MASK(%rip), %xmm14
+ paddd \TMP1, \XMM0 # INCR Y0
+ MOVADQ \XMM0, \XMM4
PSHUFB_XMM %xmm14, \XMM4 # perform a 16 byte swap
- pxor 16*0(%arg1), \XMM1
- pxor 16*0(%arg1), \XMM2
- pxor 16*0(%arg1), \XMM3
- pxor 16*0(%arg1), \XMM4
+ MOVADQ 0(%arg1),\TMP1
+ pxor \TMP1, \XMM1
+ pxor \TMP1, \XMM2
+ pxor \TMP1, \XMM3
+ pxor \TMP1, \XMM4
movdqa \TMP3, \TMP5
pshufd $78, \TMP3, \TMP1
pxor \TMP3, \TMP1
@@ -636,7 +607,23 @@ _get_AAD_loop2_done\num_initial_blocks\operation:
pshufd $78, \TMP5, \TMP1
pxor \TMP5, \TMP1
movdqa \TMP1, HashKey_4_k(%rsp)
- movaps 0xa0(%arg1), \TMP2
+ lea 0xa0(%arg1),%r10
+ mov keysize,%eax
+ shr $2,%eax # 128->4, 192->6, 256->8
+ sub $4,%eax # 128->0, 192->2, 256->4
+ jz aes_loop_pre_enc_done\num_initial_blocks
+
+aes_loop_pre_enc\num_initial_blocks:
+ MOVADQ (%r10),\TMP2
+.irpc index, 1234
+ AESENC \TMP2, %xmm\index
+.endr
+ add $16,%r10
+ sub $1,%eax
+ jnz aes_loop_pre_enc\num_initial_blocks
+
+aes_loop_pre_enc_done\num_initial_blocks:
+ MOVADQ (%r10), \TMP2
AESENCLAST \TMP2, \XMM1
AESENCLAST \TMP2, \XMM2
AESENCLAST \TMP2, \XMM3
@@ -655,15 +642,11 @@ _get_AAD_loop2_done\num_initial_blocks\operation:
movdqu \XMM4, 16*3(%arg2 , %r11 , 1)
add $64, %r11
- movdqa SHUF_MASK(%rip), %xmm14
PSHUFB_XMM %xmm14, \XMM1 # perform a 16 byte swap
pxor \XMMDst, \XMM1
# combine GHASHed value with the corresponding ciphertext
- movdqa SHUF_MASK(%rip), %xmm14
PSHUFB_XMM %xmm14, \XMM2 # perform a 16 byte swap
- movdqa SHUF_MASK(%rip), %xmm14
PSHUFB_XMM %xmm14, \XMM3 # perform a 16 byte swap
- movdqa SHUF_MASK(%rip), %xmm14
PSHUFB_XMM %xmm14, \XMM4 # perform a 16 byte swap
_initial_blocks_done\num_initial_blocks\operation:
@@ -794,7 +777,23 @@ TMP6 XMM0 XMM1 XMM2 XMM3 XMM4 XMM5 XMM6 XMM7 XMM8 operation
AESENC \TMP3, \XMM3
AESENC \TMP3, \XMM4
PCLMULQDQ 0x00, \TMP5, \XMM8 # XMM8 = a0*b0
- movaps 0xa0(%arg1), \TMP3
+ lea 0xa0(%arg1),%r10
+ mov keysize,%eax
+ shr $2,%eax # 128->4, 192->6, 256->8
+ sub $4,%eax # 128->0, 192->2, 256->4
+ jz aes_loop_par_enc_done
+
+aes_loop_par_enc:
+ MOVADQ (%r10),\TMP3
+.irpc index, 1234
+ AESENC \TMP3, %xmm\index
+.endr
+ add $16,%r10
+ sub $1,%eax
+ jnz aes_loop_par_enc
+
+aes_loop_par_enc_done:
+ MOVADQ (%r10), \TMP3
AESENCLAST \TMP3, \XMM1 # Round 10
AESENCLAST \TMP3, \XMM2
AESENCLAST \TMP3, \XMM3
@@ -986,8 +985,24 @@ TMP6 XMM0 XMM1 XMM2 XMM3 XMM4 XMM5 XMM6 XMM7 XMM8 operation
AESENC \TMP3, \XMM3
AESENC \TMP3, \XMM4
PCLMULQDQ 0x00, \TMP5, \XMM8 # XMM8 = a0*b0
- movaps 0xa0(%arg1), \TMP3
- AESENCLAST \TMP3, \XMM1 # Round 10
+ lea 0xa0(%arg1),%r10
+ mov keysize,%eax
+ shr $2,%eax # 128->4, 192->6, 256->8
+ sub $4,%eax # 128->0, 192->2, 256->4
+ jz aes_loop_par_dec_done
+
+aes_loop_par_dec:
+ MOVADQ (%r10),\TMP3
+.irpc index, 1234
+ AESENC \TMP3, %xmm\index
+.endr
+ add $16,%r10
+ sub $1,%eax
+ jnz aes_loop_par_dec
+
+aes_loop_par_dec_done:
+ MOVADQ (%r10), \TMP3
+ AESENCLAST \TMP3, \XMM1 # last round
AESENCLAST \TMP3, \XMM2
AESENCLAST \TMP3, \XMM3
AESENCLAST \TMP3, \XMM4
@@ -1155,33 +1170,29 @@ TMP7 XMM1 XMM2 XMM3 XMM4 XMMDst
pxor \TMP6, \XMMDst # reduced result is in XMMDst
.endm
-/* Encryption of a single block done*/
-.macro ENCRYPT_SINGLE_BLOCK XMM0 TMP1
- pxor (%arg1), \XMM0
- movaps 16(%arg1), \TMP1
- AESENC \TMP1, \XMM0
- movaps 32(%arg1), \TMP1
- AESENC \TMP1, \XMM0
- movaps 48(%arg1), \TMP1
- AESENC \TMP1, \XMM0
- movaps 64(%arg1), \TMP1
- AESENC \TMP1, \XMM0
- movaps 80(%arg1), \TMP1
- AESENC \TMP1, \XMM0
- movaps 96(%arg1), \TMP1
- AESENC \TMP1, \XMM0
- movaps 112(%arg1), \TMP1
- AESENC \TMP1, \XMM0
- movaps 128(%arg1), \TMP1
- AESENC \TMP1, \XMM0
- movaps 144(%arg1), \TMP1
- AESENC \TMP1, \XMM0
- movaps 160(%arg1), \TMP1
- AESENCLAST \TMP1, \XMM0
-.endm
+/* Encryption of a single block
+* uses eax & r10
+*/
+.macro ENCRYPT_SINGLE_BLOCK XMM0 TMP1
+ pxor (%arg1), \XMM0
+ mov keysize,%eax
+ shr $2,%eax # 128->4, 192->6, 256->8
+ add $5,%eax # 128->9, 192->11, 256->13
+ lea 16(%arg1), %r10 # get first expanded key address
+
+_esb_loop_\@:
+ MOVADQ (%r10),\TMP1
+ AESENC \TMP1,\XMM0
+ add $16,%r10
+ sub $1,%eax
+ jnz _esb_loop_\@
+
+ MOVADQ (%r10),\TMP1
+ AESENCLAST \TMP1,\XMM0
+.endm
/*****************************************************************************
* void aesni_gcm_dec(void *aes_ctx, // AES Key schedule. Starts on a 16
byte boundary.
* u8 *out, // Plaintext output. Encrypt in-place
is allowed.
diff --git a/arch/x86/crypto/aesni-intel_glue.c
b/arch/x86/crypto/aesni-intel_glue.c
index ae855f4..947c6bf 100644
--- a/arch/x86/crypto/aesni-intel_glue.c
+++ b/arch/x86/crypto/aesni-intel_glue.c
@@ -43,6 +43,7 @@
#include <asm/crypto/glue_helper.h>
#endif
+
/* This data is stored at the end of the crypto_tfm struct.
* It's a type of per "session" data storage location.
* This needs to be 16 byte aligned.
@@ -182,7 +183,8 @@ static void aesni_gcm_enc_avx(void *ctx, u8 *out,
u8 *hash_subkey, const u8 *aad, unsigned long aad_len,
u8 *auth_tag, unsigned long auth_tag_len)
{
- if (plaintext_len < AVX_GEN2_OPTSIZE) {
+ struct crypto_aes_ctx *aes_ctx = (struct crypto_aes_ctx*)ctx;
+ if ((plaintext_len < AVX_GEN2_OPTSIZE) || (aes_ctx-> key_length !=
AES_KEYSIZE_128)){
aesni_gcm_enc(ctx, out, in, plaintext_len, iv, hash_subkey, aad,
aad_len, auth_tag, auth_tag_len);
} else {
@@ -197,7 +199,8 @@ static void aesni_gcm_dec_avx(void *ctx, u8 *out,
u8 *hash_subkey, const u8 *aad, unsigned long aad_len,
u8 *auth_tag, unsigned long auth_tag_len)
{
- if (ciphertext_len < AVX_GEN2_OPTSIZE) {
+ struct crypto_aes_ctx *aes_ctx = (struct crypto_aes_ctx*)ctx;
+ if ((ciphertext_len < AVX_GEN2_OPTSIZE) || (aes_ctx-> key_length !=
AES_KEYSIZE_128)) {
aesni_gcm_dec(ctx, out, in, ciphertext_len, iv, hash_subkey,
aad,
aad_len, auth_tag, auth_tag_len);
} else {
@@ -231,7 +234,8 @@ static void aesni_gcm_enc_avx2(void *ctx, u8 *out,
u8 *hash_subkey, const u8 *aad, unsigned long aad_len,
u8 *auth_tag, unsigned long auth_tag_len)
{
- if (plaintext_len < AVX_GEN2_OPTSIZE) {
+ struct crypto_aes_ctx *aes_ctx = (struct crypto_aes_ctx*)ctx;
+ if ((plaintext_len < AVX_GEN2_OPTSIZE) || (aes_ctx-> key_length !=
AES_KEYSIZE_128)) {
aesni_gcm_enc(ctx, out, in, plaintext_len, iv, hash_subkey, aad,
aad_len, auth_tag, auth_tag_len);
} else if (plaintext_len < AVX_GEN4_OPTSIZE) {
@@ -250,7 +254,8 @@ static void aesni_gcm_dec_avx2(void *ctx, u8 *out,
u8 *hash_subkey, const u8 *aad, unsigned long aad_len,
u8 *auth_tag, unsigned long auth_tag_len)
{
- if (ciphertext_len < AVX_GEN2_OPTSIZE) {
+ struct crypto_aes_ctx *aes_ctx = (struct crypto_aes_ctx*)ctx;
+ if ((ciphertext_len < AVX_GEN2_OPTSIZE) || (aes_ctx-> key_length !=
AES_KEYSIZE_128)) {
aesni_gcm_dec(ctx, out, in, ciphertext_len, iv, hash_subkey,
aad, aad_len, auth_tag, auth_tag_len);
} else if (ciphertext_len < AVX_GEN4_OPTSIZE) {
@@ -511,7 +516,7 @@ static int ctr_crypt(struct blkcipher_desc *desc,
kernel_fpu_begin();
while ((nbytes = walk.nbytes) >= AES_BLOCK_SIZE) {
aesni_ctr_enc_tfm(ctx, walk.dst.virt.addr, walk.src.virt.addr,
- nbytes & AES_BLOCK_MASK, walk.iv);
+ nbytes & AES_BLOCK_MASK, walk.iv);
nbytes &= AES_BLOCK_SIZE - 1;
err = blkcipher_walk_done(desc, &walk, nbytes);
}
@@ -902,7 +907,8 @@ static int rfc4106_set_key(struct crypto_aead *parent,
const u8 *key,
}
/*Account for 4 byte nonce at the end.*/
key_len -= 4;
- if (key_len != AES_KEYSIZE_128) {
+ if (key_len != AES_KEYSIZE_128 && key_len != AES_KEYSIZE_192 &&
+ key_len != AES_KEYSIZE_256) {
crypto_tfm_set_flags(tfm, CRYPTO_TFM_RES_BAD_KEY_LEN);
return -EINVAL;
}
@@ -1013,6 +1019,7 @@ static int __driver_rfc4106_encrypt(struct aead_request
*req)
__be32 counter = cpu_to_be32(1);
struct crypto_aead *tfm = crypto_aead_reqtfm(req);
struct aesni_rfc4106_gcm_ctx *ctx = aesni_rfc4106_gcm_ctx_get(tfm);
+ u32 key_len = ctx->aes_key_expanded.key_length;
void *aes_ctx = &(ctx->aes_key_expanded);
unsigned long auth_tag_len = crypto_aead_authsize(tfm);
u8 iv_tab[16+AESNI_ALIGN];
@@ -1027,6 +1034,13 @@ static int __driver_rfc4106_encrypt(struct aead_request
*req)
/* to 8 or 12 bytes */
if (unlikely(req->assoclen != 8 && req->assoclen != 12))
return -EINVAL;
+ if (unlikely(auth_tag_len != 8 && auth_tag_len != 12 && auth_tag_len !=
16))
+ return -EINVAL;
+ if (unlikely(key_len != AES_KEYSIZE_128 &&
+ key_len != AES_KEYSIZE_192 &&
+ key_len != AES_KEYSIZE_256))
+ return -EINVAL;
+
/* IV below built */
for (i = 0; i < 4; i++)
*(iv+i) = ctx->nonce[i];
@@ -1091,6 +1105,7 @@ static int __driver_rfc4106_decrypt(struct aead_request
*req)
int retval = 0;
struct crypto_aead *tfm = crypto_aead_reqtfm(req);
struct aesni_rfc4106_gcm_ctx *ctx = aesni_rfc4106_gcm_ctx_get(tfm);
+ u32 key_len = ctx->aes_key_expanded.key_length;
void *aes_ctx = &(ctx->aes_key_expanded);
unsigned long auth_tag_len = crypto_aead_authsize(tfm);
u8 iv_and_authTag[32+AESNI_ALIGN];
@@ -1104,6 +1119,13 @@ static int __driver_rfc4106_decrypt(struct aead_request
*req)
if (unlikely((req->cryptlen < auth_tag_len) ||
(req->assoclen != 8 && req->assoclen != 12)))
return -EINVAL;
+ if (unlikely(auth_tag_len != 8 && auth_tag_len != 12 && auth_tag_len !=
16))
+ return -EINVAL;
+ if (unlikely(key_len != AES_KEYSIZE_128 &&
+ key_len != AES_KEYSIZE_192 &&
+ key_len != AES_KEYSIZE_256))
+ return -EINVAL;
+
/* Assuming we are supporting rfc4106 64-bit extended */
/* sequence numbers We need to have the AAD length */
/* equal to 8 or 12 bytes */
--
Jarod Wilson
ja...@redhat.com
--
To unsubscribe from this list: send the line "unsubscribe linux-crypto" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
