On Wed, Jun 01, 2016 at 06:04:12PM +0530, Laxman Dewangan wrote:
> The INA3221 is a three-channel, high-side current and bus voltage monitor
> with an I2C interface from Texas Instruments. The INA3221 monitors both
> shunt voltage drops and bus supply voltages in addition to having
> programmable conversion times and averaging modes for these signals.
> The INA3221 offers both critical and warning alerts to detect multiple
> programmable out-of-range conditions for each channel.
>
> Add DT binding details for INA3221 device for configuring device in
> different modes and enable multiple functionalities from device.
>
> Signed-off-by: Laxman Dewangan <ldewan...@nvidia.com>
> ---
> .../devicetree/bindings/iio/adc/ina3221.txt | 107
> +++++++++++++++++++++
> 1 file changed, 107 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/adc/ina3221.txt
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/ina3221.txt
> b/Documentation/devicetree/bindings/iio/adc/ina3221.txt
> new file mode 100644
> index 0000000..9f0908d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/ina3221.txt
> @@ -0,0 +1,107 @@
> +TI INA3221 DT binding
> +
> +The INA3221 is a three-channel, high-side current and bus voltage monitor
> +with an I2C interface from Texas Instruments. The INA3221 monitors both
> +shunt voltage drops and bus supply voltages in addition to having
> +programmable conversion times and averaging modes for these signals.
> +The INA3221 offers both critical and warning alerts to detect multiple
> +programmable out-of-range conditions for each channel.
> +
> +Required properties:
> +-------------------
> +- compatible: Must be "ti,ina3221".
> +- reg: I2C slave device address.
> +- #io-channel-cells: Should be set to 1. The value from the client node
> + represent the channel number.
> +
> +Optional properties:
> +------------------
> +one-shot-average-sample: Integer, Number of sample to average before
> + putting in the registers in oneshot mode.
> +
> +one-shot-vbus-conv-time-us: Integer in microseconds, ADC conversion time for
> + bus voltage reading in oneshot mode.
> +
> +one-shot-shunt-conv-time-us: Integer in microseconds, ADC conversion time for
> + shunt voltage reading in oneshot mode.
> +
> +continuous-average-sample: Integer, Number of sample to average before
> + putting in the registers in continuous mode.
> +
> +continuous-vbus-conv-time-us: Integer in microseconds, ADC conversion
> time for
> + bus voltage reading in continuous mode.
> +
> +continuous-shunt-conv-time-us: Integer in microseconds, ADC conversion
> time for
> + shunt voltage reading in continuous mode.
These all need vendor prefix and need to state the valid range of
values.
> +
> +enable-power-monitor: Boolean, Enable power monitoring of the
> device.
> +
> +enable-continuous-mode: Boolean. Device support oneshot and
> continuous
> + mode for the channel data conversion. Presence
> + of this property will enable the continuous
> + mode from boot.
> +
> +enable-warning-alert: Boolean, Enable the alert signal when
> shunt
> + current cross the warning threshold on any of
> + the channel. Absence of this property will not
> + enable the warning alert.
> +
> +enable-critical-alert: Boolean, Enable the alert signal when
> shunt
> + current cross the critical threshold on any
> + of the channel. Absence of this property will
> + not enable the critical alert.
Seems like these would be a user decision.
> +
> +Optional Subnode properties:
> +---------------------------
> +The channel specific properties are provided as child node of device.
> +The fixed child node names of device node used for channel identification.
> +
> +Child node's name are "channel0" for channel 0, "channel1" for channel 1 and
> +"channel2" for channel 2.
> +
> +Channel specific properties are provided under these child node. Following
> +are the properties:
> +
> +label: String, the name of the bus.
> +shunt-resistor-mohm: Integer, The shunt resistance on bus
> + in milli-ohm.
Use -micro-ohms
> +warning-current-limit-microamp: Integer in microamp, warning
> current threshold
> + for the channel to generate warning
> alert.
> +critical-current-limit-microamp: Integer in microamp, critical current
> threshold
> + for the channel to generate warning
> alert.
> +
> +Example:
> +
> +i2c@7000c400 {
> + ina3221x@42 {
What's the x?
> + compatible = "ti,ina3221";
> + reg = <0x42>;
> + one-shot-average-sample = <1>;
> + one-shot-vbus-conv-time-us = <140>;
> + one-shot-shunt-conv-time-us = <140>;
> + continuous-average-sample = <64>;
> + continuous-vbus-conv-time-us = <140>;
> + continuous-shunt-conv-time-us = <140>;
> + enable-power-monitor;
> +
> + #io-channel-cells = <1>;
> +
> + channel0 {
> + label = "VDD_MUX";
> + shunt-resistor-mohm = <20>;
> + };
> +
> + channel1 {
> + label = "VDD_5V_IO_SYS";
> + shunt-resistor-mohm = <5>;
> + warning-current-limit-microamp = <8190000>;
> + critical-current-limit-microamp = <1000000>;
> + };
> +
> + channel2 {
> + label = "VDD_3V3_SYS";
> + shunt-resistor-mohm = <10>;
> + };
> + };
> +};
> --
> 2.1.4
>
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
