Hi, Emmanuel Emmanuel Quémener schrieb: > Emmanuel Quémener a écrit : > >> Hartmut Hackmann a écrit : >> >> >>> I noticed 2 things: >>> >>> >>>> tuner 2-004b: AGC2 gain is: 10 >>>> >>>> >>> This means maximum gain. With active LNA, i would expect lower >>> values... >>> second: The reason for the tumbling channel decoder might be a >>> not closed AGC loop. >>> But if DVB-T works after analog was on once with tuner_config 3, >>> this leads me to this: >>> Analog - digital mode switch might be GPIO22 like it is with some >>> ADS / Lifeview cards. Did you ever try card=87? >>> But this would cause trouble with the LNA since in the Philips >>> solutions, GPIO22 always is involved. >>> Are you sure the board has a LNA? In the philips designs, it sits >>> under the tuner shield and looks like a SMD voltage regulator. >>> If there is a LNA, the board seems to have a mode switch we haven't >>> seen yet. Except - did you try to invert tda1004x GPIO1, so >>> .gpio_config = TDA10046_GP00_I, >>> instead >>> .gpio_config = TDA10046_GP01_I, >>> >>> Maybe this helps >>> Hartmut >>> >>> >>> >> I will do it this evening. >> >> So, if I sum up, there are 2 tests to perform : >> - #1 : try to change board from 109 to 87 : in this case, must I get an >> clean archive or do I keep some changes to tuner_config reference ? >> - #2 : try to change GPIO config reference : in this case, same as >> before : clean archive or modified one on tuner_config reference ? >> >> Bye >> >> EQ >> >> Is it necessary to keep tuner_config=3 to definitions or must I get a >> not modified archive to try to change my board from 109 to 87 and change >> only GPIO config >> > Sorry, but I didn't take the time in the past 2 weeks to experiment the > tests you'd like. > > I try on last sunday to compile a new kernel (the last one : 2.6.20) > with a blank repository on v4l-dvb archive and make the changes on it : > it sucks !!! > > - the new kernel 2.6.20 does not recognized my board > - when I try to compile new repository and install the modules, the > saa7134 module doesn't want to load > - when I search in files saa7134-dvb.c and saa-7134-cards.c the > references to tuner_config, It was impossible to find them > > So, my questions : > - how is it possible for me to compile last kernel 2.6.20 with third > party v4l-dvb archives ? > - when can I get this 2.6.20 working archives ? > - what modifications can I perform to test and make working my board > (1043:4871 reference)... > Please use my personal repository for the tests. It is at: http://linuxtv.org/hg/~hhackmann/v4l-dvb It does compile on kernel 2.6.20, i have it running here. Just to be sure: - if you compiled for another kernel before, you need to delete the file v4l/.version - don't try to merge the files into the kernel, compile them separately with make, make install (for the install, you need to be root - never mix modules with older versions. - afik, you need to enable the v4l and dvb stuff in the kernel tree.
Looks like you missed a mail from me, i will just paste it here: I had a look at the eeprom dump again: The card should be a copy of the Tiger-S reference design without radio. So please try this: Get a copy of my personal repository, compile and install. Then do: modprobe saa7134 card=109 secam=l modprobe saa7134-alsa modprobe saa7134-dvb This should do it as long as there are not tricks with the windows driver. You sould no longer need to load the saa7134-alsa and saa7134-dvb modules manually. Good luck Hartmut _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb