I was directed to http://linuxtv.org/hg/~stoth/multiproto via an off-list message but this tree is 6 months out of date and does not compile for me under 2.6.19
Why was this branch not rolled back into the main trunk ? Will Will Tatam wrote: > I sent the following email to the email address recommended for adding > support for new boards using the connexant chipset, but have had no > reply, so I'm sending to the list > > Will > > -------- Original Message -------- > Subject: Re: New Hauppauge Board > Date: Sat, 24 Feb 2007 14:44:56 -0000 (UTC) > From: [EMAIL PROTECTED] > To: [EMAIL PROTECTED] > References: <[EMAIL PROTECTED]> > > p.s I've just tried building the latest copy of hg and setting the card=18 > (the value i think it detected the similar DVB-T card as) but still no > joy, see the enclosed dmesg attachment > > Will > >> I think most of the info you need is on the website >> >> http://www.hauppauge.co.uk/pages/products/data_hvr4000.html >> >> The card was is very similar to the Nova-T PCI (connexant) that i had >> previously in thie machine, but this card isn't found by modprobe cx88-dvb >> The main chip had the same starting number for the chip (CX23882-19), but >> the last bit CX23882-?? was different. It's a bit of a pain to get the >> card back out so sorry for not giving the full details >> >> The following output was under 2.6.19-1.2288.fc5 but I can't see any >> mention of the details of this card user the hg version of CARDLIST.cx88 >> >> # lspci >> 00:00.0 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge >> 00:00.1 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge >> 00:00.2 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge >> 00:00.3 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge >> 00:00.4 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge >> 00:00.7 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge >> 00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge >> 00:0d.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host >> Controller (rev 80) >> 00:0f.0 IDE interface: VIA Technologies, Inc. >> VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) >> 00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 >> Controller (rev 81) >> 00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 >> Controller (rev 81) >> 00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 >> Controller (rev 81) >> 00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 >> Controller (rev 81) >> 00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge >> [KT600/K8T800/K8T890 South] >> 00:11.5 Multimedia audio controller: VIA Technologies, Inc. >> VT8233/A/8235/8237 AC97 Audio Controller (rev 60) >> 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev >> 78) >> 00:14.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and >> Audio Decoder (rev 05) >> 00:14.1 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio >> Decoder [Audio Port] (rev 05) >> 00:14.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio >> Decoder [MPEG Port] (rev 05) >> 00:14.4 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio >> Decoder [IR Port] (rev 05) >> 01:00.0 VGA compatible controller: VIA Technologies, Inc. S3 Unichrome Pro >> VGA Adapter (rev 02) >> >> lspci -vn >> 00:00.0 0600: 1106:0259 >> Subsystem: 1106:aa01 >> Flags: bus master, 66MHz, medium devsel, latency 8 >> Memory at d8000000 (32-bit, prefetchable) [size=128M] >> Capabilities: [80] AGP version 3.5 >> Capabilities: [50] Power Management version 2 >> >> 00:00.1 0600: 1106:1259 >> Flags: bus master, medium devsel, latency 0 >> >> 00:00.2 0600: 1106:2259 >> Flags: bus master, medium devsel, latency 0 >> >> 00:00.3 0600: 1106:3259 >> Flags: bus master, medium devsel, latency 0 >> >> 00:00.4 0600: 1106:4259 >> Flags: bus master, medium devsel, latency 0 >> >> 00:00.7 0600: 1106:7259 >> Flags: bus master, medium devsel, latency 0 >> >> 00:01.0 0604: 1106:b198 >> Flags: bus master, 66MHz, medium devsel, latency 0 >> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 >> Memory behind bridge: e4000000-e5ffffff >> Prefetchable memory behind bridge: e0000000-e3ffffff >> Capabilities: [70] Power Management version 2 >> >> 00:0d.0 0c00: 1106:3044 (rev 80) (prog-if 10) >> Subsystem: 1106:3044 >> Flags: bus master, medium devsel, latency 32, IRQ 10 >> Memory at ea002000 (32-bit, non-prefetchable) [size=2K] >> I/O ports at c000 [size=128] >> Capabilities: [50] Power Management version 2 >> >> 00:0f.0 0101: 1106:0571 (rev 06) (prog-if 8a) >> Subsystem: 1106:aa01 >> Flags: bus master, medium devsel, latency 32 >> I/O ports at c400 [size=16] >> Capabilities: [c0] Power Management version 2 >> >> 00:10.0 0c03: 1106:3038 (rev 81) >> Subsystem: 1106:aa01 >> Flags: bus master, medium devsel, latency 32, IRQ 11 >> I/O ports at c800 [size=32] >> Capabilities: [80] Power Management version 2 >> >> 00:10.1 0c03: 1106:3038 (rev 81) >> Subsystem: 1106:aa01 >> Flags: bus master, medium devsel, latency 32, IRQ 11 >> I/O ports at cc00 [size=32] >> Capabilities: [80] Power Management version 2 >> >> 00:10.2 0c03: 1106:3038 (rev 81) >> Subsystem: 1106:aa01 >> Flags: bus master, medium devsel, latency 32, IRQ 10 >> I/O ports at d000 [size=32] >> Capabilities: [80] Power Management version 2 >> >> 00:10.3 0c03: 1106:3038 (rev 81) >> Subsystem: 1106:aa01 >> Flags: bus master, medium devsel, latency 32, IRQ 10 >> I/O ports at d400 [size=32] >> Capabilities: [80] Power Management version 2 >> >> 00:11.0 0601: 1106:3227 >> Subsystem: 1106:aa01 >> Flags: bus master, stepping, medium devsel, latency 0 >> Capabilities: [c0] Power Management version 2 >> >> 00:11.5 0401: 1106:3059 (rev 60) >> Subsystem: 1106:aa01 >> Flags: medium devsel, IRQ 7 >> I/O ports at d800 [size=256] >> Capabilities: [c0] Power Management version 2 >> >> 00:12.0 0200: 1106:3065 (rev 78) >> Subsystem: 1106:0102 >> Flags: bus master, medium devsel, latency 32, IRQ 11 >> I/O ports at e000 [size=256] >> Memory at ea001000 (32-bit, non-prefetchable) [size=256] >> Capabilities: [40] Power Management version 2 >> >> 00:14.0 0400: 14f1:8800 (rev 05) >> Subsystem: 0070:6902 >> Flags: bus master, medium devsel, latency 32, IRQ 10 >> Memory at e6000000 (32-bit, non-prefetchable) [size=16M] >> Capabilities: [44] Vital Product Data >> Capabilities: [4c] Power Management version 2 >> >> 00:14.1 0480: 14f1:8811 (rev 05) >> Subsystem: 0070:6902 >> Flags: bus master, medium devsel, latency 32, IRQ 10 >> Memory at e7000000 (32-bit, non-prefetchable) [size=16M] >> Capabilities: [4c] Power Management version 2 >> >> 00:14.2 0480: 14f1:8802 (rev 05) >> Subsystem: 0070:6902 >> Flags: bus master, medium devsel, latency 32, IRQ 10 >> Memory at e8000000 (32-bit, non-prefetchable) [size=16M] >> Capabilities: [4c] Power Management version 2 >> >> 00:14.4 0480: 14f1:8804 (rev 05) >> Subsystem: 0070:6902 >> Flags: bus master, medium devsel, latency 32, IRQ 10 >> Memory at e9000000 (32-bit, non-prefetchable) [size=16M] >> Capabilities: [4c] Power Management version 2 >> >> 01:00.0 0300: 1106:3118 (rev 02) >> Subsystem: 1106:3118 >> Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 11 >> Memory at e0000000 (32-bit, prefetchable) [size=64M] >> Memory at e4000000 (32-bit, non-prefetchable) [size=16M] >> [virtual] Expansion ROM at e5000000 [disabled] [size=64K] >> Capabilities: [60] Power Management version 2 >> Capabilities: [70] AGP version 3.0 >> >> # lspci -v >> 00:00.0 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge >> Subsystem: VIA Technologies, Inc. Unknown device aa01 >> Flags: bus master, 66MHz, medium devsel, latency 8 >> Memory at d8000000 (32-bit, prefetchable) [size=128M] >> Capabilities: [80] AGP version 3.5 >> Capabilities: [50] Power Management version 2 >> >> 00:00.1 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge >> Flags: bus master, medium devsel, latency 0 >> >> 00:00.2 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge >> Flags: bus master, medium devsel, latency 0 >> >> 00:00.3 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge >> Flags: bus master, medium devsel, latency 0 >> >> 00:00.4 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge >> Flags: bus master, medium devsel, latency 0 >> >> 00:00.7 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge >> Flags: bus master, medium devsel, latency 0 >> >> 00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge (prog-if 00 >> [Normal decode]) >> Flags: bus master, 66MHz, medium devsel, latency 0 >> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 >> Memory behind bridge: e4000000-e5ffffff >> Prefetchable memory behind bridge: e0000000-e3ffffff >> Capabilities: [70] Power Management version 2 >> >> 00:0d.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host >> Controller (rev 80) (prog-if 10 [OHCI]) >> Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller >> Flags: bus master, medium devsel, latency 32, IRQ 10 >> Memory at ea002000 (32-bit, non-prefetchable) [size=2K] >> I/O ports at c000 [size=128] >> Capabilities: [50] Power Management version 2 >> >> 00:0f.0 IDE interface: VIA Technologies, Inc. >> VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if >> 8a [Master SecP PriP]) >> Subsystem: VIA Technologies, Inc. Unknown device aa01 >> Flags: bus master, medium devsel, latency 32 >> I/O ports at c400 [size=16] >> Capabilities: [c0] Power Management version 2 >> >> 00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 >> Controller (rev 81) (prog-if 00 [UHCI]) >> Subsystem: VIA Technologies, Inc. Unknown device aa01 >> Flags: bus master, medium devsel, latency 32, IRQ 11 >> I/O ports at c800 [size=32] >> Capabilities: [80] Power Management version 2 >> >> 00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 >> Controller (rev 81) (prog-if 00 [UHCI]) >> Subsystem: VIA Technologies, Inc. Unknown device aa01 >> Flags: bus master, medium devsel, latency 32, IRQ 11 >> I/O ports at cc00 [size=32] >> Capabilities: [80] Power Management version 2 >> >> 00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 >> Controller (rev 81) (prog-if 00 [UHCI]) >> Subsystem: VIA Technologies, Inc. Unknown device aa01 >> Flags: bus master, medium devsel, latency 32, IRQ 10 >> I/O ports at d000 [size=32] >> Capabilities: [80] Power Management version 2 >> >> 00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 >> Controller (rev 81) (prog-if 00 [UHCI]) >> Subsystem: VIA Technologies, Inc. Unknown device aa01 >> Flags: bus master, medium devsel, latency 32, IRQ 10 >> I/O ports at d400 [size=32] >> Capabilities: [80] Power Management version 2 >> >> 00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge >> [KT600/K8T800/K8T890 South] >> Subsystem: VIA Technologies, Inc. Unknown device aa01 >> Flags: bus master, stepping, medium devsel, latency 0 >> Capabilities: [c0] Power Management version 2 >> >> 00:11.5 Multimedia audio controller: VIA Technologies, Inc. >> VT8233/A/8235/8237 AC97 Audio Controller (rev 60) >> Subsystem: VIA Technologies, Inc. Unknown device aa01 >> Flags: medium devsel, IRQ 7 >> I/O ports at d800 [size=256] >> Capabilities: [c0] Power Management version 2 >> >> 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev >> 78) >> Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded >> Ethernet Controller on VT8235 >> Flags: bus master, medium devsel, latency 32, IRQ 11 >> I/O ports at e000 [size=256] >> Memory at ea001000 (32-bit, non-prefetchable) [size=256] >> Capabilities: [40] Power Management version 2 >> >> 00:14.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and >> Audio Decoder (rev 05) >> Subsystem: Hauppauge computer works Inc. Unknown device 6902 >> Flags: bus master, medium devsel, latency 32, IRQ 10 >> Memory at e6000000 (32-bit, non-prefetchable) [size=16M] >> Capabilities: [44] Vital Product Data >> Capabilities: [4c] Power Management version 2 >> >> 00:14.1 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio >> Decoder [Audio Port] (rev 05) >> Subsystem: Hauppauge computer works Inc. Unknown device 6902 >> Flags: bus master, medium devsel, latency 32, IRQ 10 >> Memory at e7000000 (32-bit, non-prefetchable) [size=16M] >> Capabilities: [4c] Power Management version 2 >> >> 00:14.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio >> Decoder [MPEG Port] (rev 05) >> Subsystem: Hauppauge computer works Inc. Unknown device 6902 >> Flags: bus master, medium devsel, latency 32, IRQ 10 >> Memory at e8000000 (32-bit, non-prefetchable) [size=16M] >> Capabilities: [4c] Power Management version 2 >> >> 00:14.4 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio >> Decoder [IR Port] (rev 05) >> Subsystem: Hauppauge computer works Inc. Unknown device 6902 >> Flags: bus master, medium devsel, latency 32, IRQ 10 >> Memory at e9000000 (32-bit, non-prefetchable) [size=16M] >> Capabilities: [4c] Power Management version 2 >> >> 01:00.0 VGA compatible controller: VIA Technologies, Inc. S3 Unichrome Pro >> VGA Adapter (rev 02) (prog-if 00 [VGA]) >> Subsystem: VIA Technologies, Inc. S3 Unichrome Pro VGA Adapter >> Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 11 >> Memory at e0000000 (32-bit, prefetchable) [size=64M] >> Memory at e4000000 (32-bit, non-prefetchable) [size=16M] >> [virtual] Expansion ROM at e5000000 [disabled] [size=64K] >> Capabilities: [60] Power Management version 2 >> Capabilities: [70] AGP version 3.0 >> >> >> >> >> > > > ------------------------------------------------------------------------ > > Linux version 2.6.19-1.2288.fc5 ([EMAIL PROTECTED]) (gcc version 4.1.1 > 20070105 (Red Hat 4.1.1-51)) #1 Sat Feb 10 14:27:07 EST 2007 > BIOS-provided physical RAM map: > BIOS-e820: 0000000000000000 - 000000000009f800 (usable) > BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) > BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) > BIOS-e820: 0000000000100000 - 000000001bff0000 (usable) > BIOS-e820: 000000001bff0000 - 000000001bff3000 (ACPI NVS) > BIOS-e820: 000000001bff3000 - 000000001c000000 (ACPI data) > BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) > 0MB HIGHMEM available. > 447MB LOWMEM available. > Using x86 segment limits to approximate NX protection > Entering add_active_range(0, 0, 114672) 0 entries of 256 used > Zone PFN ranges: > DMA 0 -> 4096 > Normal 4096 -> 114672 > HighMem 114672 -> 114672 > early_node_map[1] active PFN ranges > 0: 0 -> 114672 > On node 0 totalpages: 114672 > DMA zone: 32 pages used for memmap > DMA zone: 0 pages reserved > DMA zone: 4064 pages, LIFO batch:0 > Normal zone: 863 pages used for memmap > Normal zone: 109713 pages, LIFO batch:31 > HighMem zone: 0 pages used for memmap > DMI not present or invalid. > Using APIC driver default > ACPI: RSDP (v000 CN400 ) @ 0x000f6aa0 > ACPI: RSDT (v001 CN400 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1bff3000 > ACPI: FADT (v001 CN400 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1bff3040 > ACPI: DSDT (v001 CN400 AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000 > ACPI: Disabling ACPI support > Allocating PCI resources starting at 20000000 (gap: 1c000000:e3ff0000) > Detected 1333.397 MHz processor. > Built 1 zonelists. Total pages: 113777 > Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet > No local APIC present or hardware disabled > mapped APIC to ffffd000 (0139c000) > Enabling fast FPU save and restore... done. > Enabling unmasked SIMD FPU exception support... done. > Initializing CPU#0 > CPU 0 irqstacks, hard=c076c000 soft=c076b000 > PID hash table entries: 2048 (order: 11, 8192 bytes) > Console: colour VGA+ 80x25 > Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) > Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) > Memory: 448460k/458688k available (2083k kernel code, 9600k reserved, 807k > data, 228k init, 0k highmem) > virtual kernel memory layout: > fixmap : 0xfff9a000 - 0xfffff000 ( 404 kB) > pkmap : 0xff800000 - 0xffc00000 (4096 kB) > vmalloc : 0xdc800000 - 0xff7fe000 ( 559 MB) > lowmem : 0xc0000000 - 0xdbff0000 ( 447 MB) > .init : 0xc072d000 - 0xc0766000 ( 228 kB) > .data : 0xc0608c72 - 0xc06d2af4 ( 807 kB) > .text : 0xc0400000 - 0xc0608c72 (2083 kB) > Checking if this processor honours the WP bit even in supervisor mode... Ok. > Calibrating delay using timer specific routine.. 2668.74 BogoMIPS > (lpj=1334373) > Security Framework v1.0.0 initialized > SELinux: Initializing. > SELinux: Starting in permissive mode > selinux_register_security: Registering secondary module capability > Capability LSM initialized as secondary > Mount-cache hash table entries: 512 > CPU: After generic identify, caps: 0381b83f 00000000 00000000 00000000 > 00000000 00000000 00000000 > CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line) > CPU: L2 Cache: 64K (32 bytes/line) > CPU: After all inits, caps: 0381b13f 00000000 00000000 00000000 00000000 > 000000dd 00000000 > CPU: Centaur VIA Nehemiah stepping 08 > Checking 'hlt' instruction... OK. > checking if image is initramfs... it is > Freeing initrd memory: 1542k freed > NET: Registered protocol family 16 > PCI: PCI BIOS revision 2.10 entry at 0xfad70, last bus=1 > PCI: Using configuration type 1 > Setting up standard PCI resources > ACPI: Interpreter disabled. > Linux Plug and Play Support v0.97 (c) Adam Belay > pnp: PnP ACPI: disabled > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > PCI: Probing PCI hardware > PCI: Probing PCI hardware (bus 00) > Boot video device is 0000:01:00.0 > PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0 > NetLabel: Initializing > NetLabel: domain hash size = 128 > NetLabel: protocols = UNLABELED CIPSOv4 > NetLabel: unlabeled traffic allowed by default > PCI: Bridge: 0000:00:01.0 > IO window: disabled. > MEM window: e4000000-e5ffffff > PREFETCH window: e0000000-e3ffffff > PCI: Setting latency timer of device 0000:00:01.0 to 64 > NET: Registered protocol family 2 > IP route cache hash table entries: 4096 (order: 2, 16384 bytes) > TCP established hash table entries: 16384 (order: 6, 262144 bytes) > TCP bind hash table entries: 8192 (order: 5, 163840 bytes) > TCP: Hash tables configured (established 16384 bind 8192) > TCP reno registered > apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) > audit: initializing netlink socket (disabled) > audit(1172327905.858:1): initialized > Total HugeTLB memory allocated, 0 > VFS: Disk quotas dquot_6.5.1 > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > SELinux: Registering netfilter hooks > ksign: Installing public key data > Loading keyring > - Added public key 38BFE5B32FEF5C5 > - User ID: Red Hat, Inc. (Kernel Module GPG key) > io scheduler noop registered > io scheduler anticipatory registered > io scheduler deadline registered > io scheduler cfq registered (default) > PCI: Bypassing VIA 8237 APIC De-Assert Message > isapnp: Scanning for PnP cards... > isapnp: No Plug & Play device found > Real Time Clock Driver v1.12ac > Non-volatile memory driver v1.2 > Linux agpgart interface v0.101 (c) Dave Jones > agpgart: Detected VIA PM800/PN800/PM880/PN880 chipset > agpgart: AGP aperture is 128M @ 0xd8000000 > Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled > serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx > VP_IDE: IDE controller at PCI slot 0000:00:0f.0 > VP_IDE: chipset revision 6 > VP_IDE: not 100% native mode: will probe irqs later > VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.0 > ide0: BM-DMA at 0xc400-0xc407, BIOS settings: hda:DMA, hdb:pio > ide1: BM-DMA at 0xc408-0xc40f, BIOS settings: hdc:DMA, hdd:pio > Probing IDE interface ide0... > hda: SAMSUNG SP1604N, ATA DISK drive > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > Probing IDE interface ide1... > hdc: SONY DVD RW DRU-510A, ATAPI CD/DVD-ROM drive > ide1 at 0x170-0x177,0x376 on irq 15 > hda: max request size: 512KiB > hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63, > UDMA(100) > hda: cache flushes supported > hda: hda1 hda2 > ide-floppy driver 0.99.newide > usbcore: registered new interface driver libusual > usbcore: registered new interface driver hiddev > usbcore: registered new interface driver usbhid > drivers/usb/input/hid-core.c: v2.6:USB HID core driver > PNP: No PS/2 controller found. Probing ports directly. > serio: i8042 KBD port at 0x60,0x64 irq 1 > serio: i8042 AUX port at 0x60,0x64 irq 12 > mice: PS/2 mouse device common for all mice > TCP bic registered > Initializing XFRM netlink socket > NET: Registered protocol family 1 > NET: Registered protocol family 17 > Using IPI Shortcut mode > Time: tsc clocksource has been installed. > Freeing unused kernel memory: 228k freed > Write protecting the kernel read-only data: 391k > input: AT Translated Set 2 keyboard as /class/input/input0 > logips2pp: Detected unknown logitech mouse model 1 > input: PS/2 Logitech Mouse as /class/input/input1 > device-mapper: ioctl: 4.10.0-ioctl (2006-09-14) initialised: [EMAIL PROTECTED] > kjournald starting. Commit interval 5 seconds > EXT3-fs: mounted filesystem with ordered data mode. > SELinux: Disabled at runtime. > SELinux: Unregistering netfilter hooks > audit(1172327910.452:2): selinux=0 auid=4294967295 > hdc: ATAPI 32X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33) > Uniform CD-ROM driver Revision: 3.20 > Linux video capture interface: v2.00 > input: PC Speaker as /class/input/input2 > via-rhine.c:v1.10-LK1.4.2 Sept-11-2006 Written by Donald Becker > PCI: setting IRQ 11 as level-triggered > PCI: Found IRQ 11 for device 0000:00:12.0 > PCI: Sharing IRQ 11 with 0000:00:10.0 > PCI: Sharing IRQ 11 with 0000:00:10.1 > eth0: VIA Rhine II at 0xea001000, 00:40:63:e5:09:2d, IRQ 11. > eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1. > cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded > CORE cx88[0]: subsystem: 0070:6902, board: Hauppauge Nova-T DVB-T > [card=18,insmod option] > TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe > cx2388x v4l2 driver version 0.0.6 loaded > tveeprom 1-0050: Hauppauge model 69009, rev B2A0, serial# 1243050 > tveeprom 1-0050: MAC address is 00-0D-FE-12-F7-AA > tveeprom 1-0050: tuner model is Philips FMD1216ME (idx 100, type 63) > tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) > ATSC/DVB Digital (eeprom 0xf4) > tveeprom 1-0050: audio processor is CX882 (idx 33) > tveeprom 1-0050: decoder processor is CX882 (idx 25) > tveeprom 1-0050: has radio, has IR receiver, has no IR transmitter > cx88[0]: warning: unknown hauppauge model #69009 > cx88[0]: hauppauge eeprom: model=69009 > input: cx88 IR (Hauppauge Nova-T DVB-T as /class/input/input3 > cx88[0]/2: cx2388x 8802 Driver Manager > PCI: setting IRQ 10 as level-triggered > PCI: Found IRQ 10 for device 0000:00:14.2 > PCI: Sharing IRQ 10 with 0000:00:0d.0 > PCI: Sharing IRQ 10 with 0000:00:10.2 > PCI: Sharing IRQ 10 with 0000:00:10.3 > PCI: Sharing IRQ 10 with 0000:00:14.0 > PCI: Sharing IRQ 10 with 0000:00:14.1 > PCI: Sharing IRQ 10 with 0000:00:14.4 > cx88[0]/2: found at 0000:00:14.2, rev: 5, irq: 10, latency: 32, mmio: > 0xe8000000 > PCI: Found IRQ 10 for device 0000:00:14.0 > PCI: Sharing IRQ 10 with 0000:00:0d.0 > PCI: Sharing IRQ 10 with 0000:00:10.2 > PCI: Sharing IRQ 10 with 0000:00:10.3 > PCI: Sharing IRQ 10 with 0000:00:14.1 > PCI: Sharing IRQ 10 with 0000:00:14.2 > PCI: Sharing IRQ 10 with 0000:00:14.4 > cx88[0]/0: found at 0000:00:14.0, rev: 5, irq: 10, latency: 32, mmio: > 0xe6000000 > cx88[0]/0: registered device video0 [v4l2] > cx88[0]/0: registered device vbi0 > cx88[0]/0: registered device radio0 > PCI: setting IRQ 7 as level-triggered > PCI: Found IRQ 7 for device 0000:00:11.5 > PCI: Setting latency timer of device 0000:00:11.5 to 64 > cx2388x alsa driver version 0.0.6 loaded > PCI: Found IRQ 10 for device 0000:00:14.1 > PCI: Sharing IRQ 10 with 0000:00:0d.0 > PCI: Sharing IRQ 10 with 0000:00:10.2 > PCI: Sharing IRQ 10 with 0000:00:10.3 > PCI: Sharing IRQ 10 with 0000:00:14.0 > PCI: Sharing IRQ 10 with 0000:00:14.2 > PCI: Sharing IRQ 10 with 0000:00:14.4 > cx88[0]/1: CX88x/0: ALSA support for cx2388x boards > USB Universal Host Controller Interface driver v3.0 > PCI: Found IRQ 11 for device 0000:00:10.0 > PCI: Sharing IRQ 11 with 0000:00:10.1 > PCI: Sharing IRQ 11 with 0000:00:12.0 > uhci_hcd 0000:00:10.0: UHCI Host Controller > uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 > uhci_hcd 0000:00:10.0: irq 11, io base 0x0000c800 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 2 ports detected > PCI: Found IRQ 11 for device 0000:00:10.1 > PCI: Sharing IRQ 11 with 0000:00:10.0 > PCI: Sharing IRQ 11 with 0000:00:12.0 > uhci_hcd 0000:00:10.1: UHCI Host Controller > uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 > uhci_hcd 0000:00:10.1: irq 11, io base 0x0000cc00 > usb usb2: configuration #1 chosen from 1 choice > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 2 ports detected > PCI: Found IRQ 10 for device 0000:00:10.2 > PCI: Sharing IRQ 10 with 0000:00:0d.0 > PCI: Sharing IRQ 10 with 0000:00:10.3 > PCI: Sharing IRQ 10 with 0000:00:14.0 > PCI: Sharing IRQ 10 with 0000:00:14.1 > PCI: Sharing IRQ 10 with 0000:00:14.2 > PCI: Sharing IRQ 10 with 0000:00:14.4 > uhci_hcd 0000:00:10.2: UHCI Host Controller > uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 > uhci_hcd 0000:00:10.2: irq 10, io base 0x0000d000 > usb usb3: configuration #1 chosen from 1 choice > hub 3-0:1.0: USB hub found > hub 3-0:1.0: 2 ports detected > PCI: Found IRQ 10 for device 0000:00:10.3 > PCI: Sharing IRQ 10 with 0000:00:0d.0 > PCI: Sharing IRQ 10 with 0000:00:10.2 > PCI: Sharing IRQ 10 with 0000:00:14.0 > PCI: Sharing IRQ 10 with 0000:00:14.1 > usb 1-1: new full speed USB device using uhci_hcd and address 2 > PCI: Sharing IRQ 10 with 0000:00:14.2 > PCI: Sharing IRQ 10 with 0000:00:14.4 > uhci_hcd 0000:00:10.3: UHCI Host Controller > uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 > uhci_hcd 0000:00:10.3: irq 10, io base 0x0000d400 > usb usb4: configuration #1 chosen from 1 choice > hub 4-0:1.0: USB hub found > hub 4-0:1.0: 2 ports detected > ieee1394: Initialized config rom entry `ip1394' > usb 1-1: configuration #1 chosen from 1 choice > PCI: Found IRQ 10 for device 0000:00:0d.0 > PCI: Sharing IRQ 10 with 0000:00:10.2 > PCI: Sharing IRQ 10 with 0000:00:10.3 > PCI: Sharing IRQ 10 with 0000:00:14.0 > PCI: Sharing IRQ 10 with 0000:00:14.1 > PCI: Sharing IRQ 10 with 0000:00:14.2 > PCI: Sharing IRQ 10 with 0000:00:14.4 > ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[ea002000-ea0027ff] > Max Packet=[2048] IR/IT contexts=[4/8] > usb 1-2: new low speed USB device using uhci_hcd and address 3 > usb 1-2: configuration #1 chosen from 1 choice > input: CHESEN USB Keyboard as /class/input/input4 > input: USB HID v1.10 Keyboard [CHESEN USB Keyboard] on usb-0000:00:10.0-2 > input: CHESEN USB Keyboard as /class/input/input5 > input: USB HID v1.10 Device [CHESEN USB Keyboard] on usb-0000:00:10.0-2 > ieee1394: Host added: ID:BUS[0-00:1023] GUID[0040635000071590] > drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 > proto 2 vid 0x04E8 pid 0x3242 > usbcore: registered new interface driver usblp > drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver > Floppy drive(s): fd0 is unknown type 15 (usb?), fd1 is unknown type 15 (usb?) > floppy0: no floppy controllers found > lp: driver loaded but no devices found > NET: Registered protocol family 10 > lo: Disabled Privacy Extensions > Mobile IPv6 > md: Autodetecting RAID arrays. > md: autorun ... > md: ... autorun DONE. > EXT3 FS on dm-0, internal journal > kjournald starting. Commit interval 5 seconds > EXT3 FS on hda1, internal journal > EXT3-fs: mounted filesystem with ordered data mode. > kjournald starting. Commit interval 5 seconds > EXT3 FS on dm-1, internal journal > EXT3-fs: mounted filesystem with ordered data mode. > Adding 917496k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 > across:917496k > eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 > audit(1172327938.750:3): audit_pid=1692 old=0 by auid=4294967295 > Bluetooth: Core ver 2.11 > NET: Registered protocol family 31 > Bluetooth: HCI device and connection manager initialized > Bluetooth: HCI socket layer initialized > Bluetooth: L2CAP ver 2.8 > Bluetooth: L2CAP socket layer initialized > Bluetooth: RFCOMM socket layer initialized > Bluetooth: RFCOMM TTY layer initialized > Bluetooth: RFCOMM ver 1.8 > Bluetooth: HIDP (Human Interface Emulation) ver 1.1 > eth0: no IPv6 routers present > Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]). > NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory > NFSD: starting 90-second grace period > cx2388x dvb driver version 0.0.6 loaded > cx8802_register_driver() ->registering driver type=dvb access=shared > CORE cx88[0]: subsystem: 0070:6902, board: Hauppauge Nova-T DVB-T [card=18] > cx88[0]/2: cx2388x based dvb card > cx22702_readreg: readreg error (ret == -121) > cx88[0]: frontend initialization failed > cx8802_dvb_probe dvb_register failed err = -1 > cx8802_register_driver() ->probe failed err = -1 > saa7146: register extension 'budget_ci dvb'. > [drm] Initialized drm 1.0.1 20051102 > [drm] Initialized via 2.10.0 20060529 on minor 0 > agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0. > agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode > agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode > > > > ------------------------------------------------------------------------ > > _______________________________________________ > linux-dvb mailing list > linux-dvb@linuxtv.org > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
